top of page

Vladimir Matias

iBeam Materials

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Vladimir Matias | iBeam Materials: How does iBeam grow single-crystal-like epitaxial GaN directly on unpolished, as-rolled metal foil?

06:50 - 08:49

Other snippets from this talk

Summary of the clip:

How does iBeam grow single-crystal-like epitaxial GaN directly on unpolished, as-rolled metal foil?

The breakthrough removes the single-crystal wafer from epitaxial indium gallium nitride LED deposition entirely. For the first time in history, high-quality epitaxial opto-semiconductors are deposited directly on a non-single-crystal substrate. Metal foil is the substrate used here, but the same GANox process — epitaxial GaN deposited on X, where X is any of many materials — extends to glass and ceramics as well.

An ion beam process orients a nanometer-thin layer on top of the substrate so that all the grains are aligned. That template replaces the single-crystal sapphire wafer. Because the metal foils are used as rolled and remain rather rough, the surface is first planarized by chemical solution deposition, creating an atomically smooth surface before the ion beam aligned layer is deposited.

Cross-sectional electron microscopy shows the resulting structure, and the first LED is visible with the rough metal foil seen through the gallium nitride. Gallium nitride and LED deposition were carried out by collaborators at Sandia National Laboratory in New Mexico. The open question posed is why replacing the substrate matters, given the same gallium nitride LED material is still being used.

In this short video, you can learn:
* GANox deposits epitaxial GaN on X, where X can be metal foil, glass or ceramics instead of a single-crystal wafer.
* A nanometer-thin ion-beam-aligned layer aligns all the grains, forming a template that substitutes for single-crystal sapphire.
* Chemical solution deposition planarizes as-rolled rough foil to an atomically smooth surface before the aligned layer is deposited.

📋 **Clip Abstract** The GANox process deposits high-quality epitaxial indium gallium nitride LED material directly on non-single-crystal substrates such as as-rolled metal foil, glass and ceramics. An ion-beam-aligned nanometer-thin template replaces the sapphire wafer, enabled by chemical solution deposition planarization to atomic smoothness, with the first LED deposited by Sandia National Laboratory collaborators.

About the speaker:
* Speaker: Vladimir Matias
* Company: iBeam Materials
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#GANox, #IonBeamAlignedTemplate, #ChemicalSolutionDeposition, #GaNOnMetalFoil, #MicroLEDDisplays, #EpitaxialGrowth

This is a highlight of the presentation:

Large-area LED sheets for microLED displays fabricated R2R directly on metal foil

Displays & Lighting 2021: Innovations & Market Trends

​

14-16 July 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

11:02 - 13:21

Can roll-to-roll deposition on metal foil cut epi-GaN LED costs 20-fold versus sapphire wafers?

Can roll-to-roll deposition on metal foil cut epi-GaN LED costs 20-fold versus sapphire wafers?

Depositing LEDs on inexpensive, flexible and robust metal foil enables roll-to-roll manufacturing instead of single-crystal wafers. The GaNox process can be scaled and automated to kilometer-long rolls of metal substrate — a scale-up of five orders of magnitude over wafers, ultimately reducing cost by more than 20-fold. The substrate's better thermal conductivity also improves the deposition process, delivering better wavelength uniformity of the LEDs, among other benefits.

GaN epitaxy is expensive, and the industry-standard deposition process, metal-organic chemical vapor deposition (MOCVD), is rather expensive. Current 5-micron-thick epi-GaN LEDs cost about $2 to $3 per square centimetre. Plotted on a log scale against the practical lower limit of materials costs, there is plenty of room at the bottom. Twenty percent of the current cost is simply the sapphire substrate.

Scaling to roll-to-roll or sheet-to-sheet MOCVD, while keeping MOCVD, reduces cost by at most a factor of four. A hybrid process — using a lower-cost deposition method for the gallium nitride buffer layer — is believed to cut cost by another factor of five. That brings epi cost to competitiveness with OLED materials deposition, so mobile displays can now be made with microLEDs.

In this short video, you can learn:
* A substrate area five orders of magnitude larger than a wafer underpins the claimed more-than-20-fold cost reduction.
* Metal foil's better thermal conductivity improves the deposition process and the wavelength uniformity of the resulting LEDs.
* The sapphire substrate alone is 20% of today's $2 to $3 per square centimetre epi-GaN cost.

📋 **Clip Abstract** Roll-to-roll GaNox deposition on metal foil scales substrate area five orders of magnitude beyond single-crystal wafers, targeting more than a 20-fold cost reduction for epi-GaN LEDs. Against today's $2 to $3 per square centimetre MOCVD material cost, a hybrid buffer-layer process is projected to reach OLED-comparable deposition cost and open microLED mobile displays.

About the speaker:
* Speaker: Vladimir Matias
* Company: iBeam Materials
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#RollToRollMOCVD, #MetalFoilGaN, #GaNoxProcess, #WavelengthUniformity, #MicroLEDDisplays, #EpitaxialMaterials

21:28 - 23:46

What limits roll-to-roll GaN growth, and how does foil-based LED photoluminescence compare with sapphire today?

What limits roll-to-roll GaN growth, and how does foil-based LED photoluminescence compare with sapphire today?

Roll-to-roll processing can run at very high speed, up to kilometers per hour, but the primary bottleneck is gallium nitride deposition when a thick GaN layer is required. A hybrid approach uses high-rate hydride vapor phase epitaxy, or HVPE, depositing hundreds of microns per hour. That could reduce the thick buffer-layer step to a minute or two, making the GaN buffer much faster to deposit.

Despite that route, no one, including this team, has yet made roll-to-roll gallium nitride; it remains the next challenge. A bench effort is planned, and fundraising is underway for that next task. So the high-speed foil concept is established, but R2R GaN growth itself has not been accomplished yet.

Sample LEDs made with the intermediary layer are not optimized; samples were produced by exchanging with another laboratory. Photoluminescence is about 70% of the signal compared with sapphire LEDs. The team believes that, based on threading dislocation densities, sapphire performance can ultimately be reached, leaving room for improvement at sample level today.

In this short video, you can learn:
* The main bottleneck in roll-to-roll GaN growth is depositing a thick gallium nitride layer, not the foil transport speed.
* A hybrid HVPE route can deposit hundreds of microns per hour, potentially reducing the GaN buffer deposition to one or two minutes.
* Foil-based samples currently show about 70% of sapphire LED photoluminescence, with threading dislocation densities suggesting sapphire performance is ultimately attainable.

📋 **Clip Abstract** Roll-to-roll GaN growth is limited by thick gallium nitride deposition, so a hybrid HVPE approach is proposed to deposit hundreds of microns per hour and shorten buffer deposition to minutes. No roll-to-roll GaN has yet been made, while samples with an intermediary layer show about 70% of sapphire LED photoluminescence and are expected to reach sapphire performance based on threading dislocation densities.

About the speaker:
* Speaker: Vladimir Matias
* Company: iBeam Materials
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#RollToRollGaN, #HVPEBufferLayer, #MetalFoilLED, #Photoluminescence70, #MicroLEDDisplays, #GaNEpitaxy

15:14 - 17:35

Why does monolithic integration of LED sheets on flexible substrates outperform traditional pick-and-place mass transfer for displays?

Why does monolithic integration of LED sheets on flexible substrates outperform traditional pick-and-place mass transfer for displays?

Large-area LED sheets enable monolithic integration of microLED displays without any transfer step, which the talk argues leads to much greater yield and reliability because there is no mechanical transfer. Redundancy can be built in if needed. Thin-film transistors can then be deposited directly over the epi-GaN sheet, and because the whole area is available for integration, gallium nitride FETs can be made from that same epitaxial material.

In this way the whole display can be monolithically integrated in a single plane, with no more a front and back plane. Quantum dot technology can convert blue light, so the entire sheet of LEDs is made blue and red and green quantum dots are patterned within each pixel by lithography or some kind of printing, depending on the size of the display.

Unlike mass transfer microLED displays, the monolithically integrated LED sheet brings inherent capabilities: a paper-thin, flexible and thermally well-conducting substrate as the display platform. LED sizes can be larger than typical for mass transfer since the whole sheet contains epi material, so efficiencies could be greater. Scaling to higher resolution keeps emitter cost essentially the same, as emitters are simply patterned on a finer scale, which in turn allows 3D light-field display technologies.

In this short video, you can learn:
* Eliminating mechanical transfer is claimed to raise LED device yield and reliability, with redundancy designed in where needed.
* Since the full epitaxial sheet is available, TFTs and GaN FETs can be integrated, collapsing front and back planes into one plane.
* Red and green quantum dots patterned by lithography or printing convert a blue LED sheet, and finer patterning keeps emitter cost essentially flat.

📋 **Clip Abstract** Large-area LED sheets allow microLED displays to be monolithically integrated without pick-and-place transfer, which is argued to raise yield and reliability. The same epitaxial gallium nitride sheet supports TFTs and GaN FETs in one plane, quantum-dot color conversion, a paper-thin flexible thermally conducting platform, and emitter cost that stays essentially flat as resolution scales.

About the speaker:
* Speaker: Vladimir Matias
* Company: iBeam Materials
* Event: Displays & Lighting 2021: Innovations & Market Trends

Join TechBlick to learn about the cutting edge in the display industry
https://www.techblick.com/

#EpiGaNSheet, #QuantumDotPatterning, #MonolithicLEDSheet, #GaNFETIntegration, #MicroLEDDisplays, #FlexibleElectronics


About this talk

→ Large-area LED sheets for microLED displays fabricated R2R directly on metal foil · Vladimir Matias · Displays & Lighting: Innovations & Market Trends 2021


Other talks by Vladimir Matias

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page