Yun-Chang Chao | Everlight: Why does oxygen barrier matter, and when is full-area blanket sealing chosen over other seal configurations?
11:42 - 13:51
Other snippets from this talk
Summary of the clip:
Why does oxygen barrier matter, and when is full-area blanket sealing chosen over other seal configurations?
Moisture is the first performance axis when categorising seal choices. The package design must control edge geometry and maintain uniform thickness across the whole solar cell. If cell thickness is uneven, mechanical stress can arise, and thermal cycling can accumulate that stress. These design controls sit alongside data-sheet results, so the seal decision is not only a materials comparison.
Oxygen barrier is the second axis. AB 302 is reported to have a very good oxygen barrier compared with TPO and PIB. Academic partners are using the approach for tin-based perovskite outdoor testing, and feedback from NREL—now NRL—says oxygen is very crucial for outdoor testing. The left-side comparison shows OTR data.
For blanket sealing, some partners use 341 for full-area sealing, and combining sealant with PIB can give very good performance. The practical categorisation therefore links moisture, controlled edge geometry and uniform thickness, accumulated thermal-cycle stress, and oxygen-barrier performance. OTR comparison is the reference for choosing among these seal configurations.
In this short video, you can learn:
* Uniform cell thickness is a package-design control because uneven thickness can create mechanical stress that accumulates during thermal cycling.
* AB 302 offers a very good oxygen barrier compared with TPO and PIB, and oxygen is described as crucial for outdoor testing.
* Some partners use 341 for full-area blanket sealing, while sealant-plus-PIB combinations can deliver very good performance.
📋 **Clip Abstract** Seal selection for perovskite commercialization is framed by moisture, package edge geometry and uniform cell thickness, thermal-cycle stress accumulation, and oxygen barrier. AB 302 is compared with TPO and PIB on oxygen barrier, with OTR data and outdoor tin-based perovskite testing feedback cited.
About the speaker:
* Speaker: Yun-Chang Chao
* Company: Everlight
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#AB302, #OxygenBarrier, #FullAreaBlanketSealing, #OTRComparison, #PerovskiteEncapsulation, #TinPerovskiteOutdoorTesting
This is a highlight of the presentation:
Practical Encapsulation Factors for Reliable Perovskite Commercialization
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
03:41 - 04:36
Is a strong bulk moisture barrier enough if the encapsulant interface adhesion is weak?
Is a strong bulk moisture barrier enough if the encapsulant interface adhesion is weak?
EverSolar EV341 is presented as having very good barrier properties, and that is part of why groups including Snaith, Strank, Valencia Henkelman and others use the encapsulant. The argument does not compete on barrier property alone: mechanical factors and interfaces are also described as very important factors to consider.
The key warning is interface adhesion: if the interface adhesion is weak, moisture can still pass through the interfaces even when the bulk permeation barrier properties are very good. This is framed as easy to overlook, so a strong bulk barrier alone does not address all encapsulation factors.
Instead of competing on barrier property, the talk shifts attention to other factors: mechanical behavior and interfaces. The practical point is that encapsulation depends on both bulk barrier performance and adhesion at interfaces, because moisture can pass through weak interface paths even with good bulk properties.
In this short video, you can learn:
* EverSolar EV341 is cited as having very good barrier properties and is used by several research groups.
* Weak interface adhesion allows moisture to pass through interfaces even when bulk permeation barrier properties are very good.
* Mechanical factors and interfaces are described as important and easy to overlook in encapsulation.
📋 **Clip Abstract** EverSolar EV341 is presented as having very good barrier properties, with several groups using the encapsulant. The talk argues that mechanical factors and interface adhesion also matter, because weak interfaces can let moisture pass even with good bulk permeation barrier properties.
About the speaker:
* Speaker: Yun-Chang Chao
* Company: Everlight
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#EverSolarEV341, #EncapsulantAdhesion, #BulkBarrierProperties, #WeakInterfaceAdhesion, #PerovskiteEncapsulation, #PerovskiteSolarCells
09:09 - 10:58
Why do compact perovskite products leave only 0.5–1.5 mm for encapsulation, and what material meets that?
Why do compact perovskite products leave only 0.5–1.5 mm for encapsulation, and what material meets that?
The clip frames reliability around thermal stress: if perovskite is too sensitive to it, small solar cells need to preserve PCE during transportation. Outdoor testing is described as very hard, especially in countries with very hot weather. These are the conditions invoked before turning to commercial integration into compact electronics.
A UV tracker is given as the example, integrating perovskite solar cells in a very small size. The question is how much width remains for the encapsulant: only 0.5 millimeter to 1.5 millimeter. The electronic maker wants to maximize the active layer to collect more electricity, and tells the encapsulation supplier that this is the supplier’s problem, not theirs.
The stated response is Evosol AB 341 as the better solution for that narrow encapsulation budget. The speaker also says an improved version of AB 341 already exists, though the clip cuts off around that point. No further material data or lifetime result is provided in this segment.
In this short video, you can learn:
* Compact perovskite electronics can leave only 0.5–1.5 mm for encapsulant because makers maximize active area.
* Thermal stress and hot-weather outdoor testing are cited as reliability pressures for small perovskite solar cells.
* Evosol AB 341 is presented as the better encapsulation solution, with an improved version said to exist.
📋 **Clip Abstract** The clip links perovskite reliability to thermal stress, transportation PCE retention and hard outdoor testing in hot weather. It then shows a tiny UV tracker with only 0.5–1.5 mm encapsulant width and names Evosol AB 341, plus an improved version, as the proposed answer.
About the speaker:
* Speaker: Yun-Chang Chao
* Company: Everlight
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#EvosolAB341, #EncapsulantWidth, #UVTrackerPerovskite, #ThermalStressPCE, #PerovskiteSolarCells, #SolarCellEncapsulation
04:50 - 06:35
How does an electrode feed-through become a moisture path, and which joint design avoids it?
How does an electrode feed-through become a moisture path, and which joint design avoids it?
Avoid electrode feed-through by making the electrical joint first and keeping the crossing flat and thin. In a normal small solar cell, the electrode passes through the encapsulation because electricity must be measured; that is exactly the feed-through situation, so moisture can pass along the highlighted red line.
Another design, based on the Valencia group, makes the joint first. It may be better because treatment is easier on the copper wire and the hole is smaller. The joint encapsulant can also reinforce the part, so this can be a choice.
A further example keeps the electrode from passing through the encapsulation. Instead, it is integrated with the conducting adhesive and the PCB board. This illustrates the same practical route: remove the feed-through path and integrate the electrical connection within the encapsulation scheme.
In this short video, you can learn:
* Electrode feed-through creates a continuous moisture path through the encapsulation.
* Making the electrical joint first and keeping the crossing flat and thin avoids that feed-through.
* A smaller hole, easier copper-wire treatment and joint encapsulant reinforcement can support the Valencia-style joint design.
📋 **Clip Abstract** Electrode feed-through is identified as a moisture path because the electrode passes through the encapsulation for electrical measurement. Alternative joint designs make the electrical connection first, keep the crossing flat and thin, use a smaller hole and copper-wire treatment, and integrate the electrode with conducting adhesive and PCB board.
About the speaker:
* Speaker: Yun-Chang Chao
* Company: Everlight
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ElectrodeFeedThrough, #MoisturePath, #JointEncapsulant, #ConductingAdhesive, #PerovskiteSolarCells, #PVEncapsulation
About this talk
→ Practical Encapsulation Factors for Reliable Perovskite Commercialization · Yun-Chang Chao · Perovskite Connect 2026


