top of page

Zachary J. Davis

Danish Technological Institute

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Zachary J. Davis | Danish Technological Institute: How does a printed PTC heater self-limit at 42–43°C while surviving 50 wash cycles?

11:10 - 13:16

Other snippets from this talk

Summary of the clip:

How does a printed PTC heater self-limit at 42–43°C while surviving 50 wash cycles?

The printed heater stack comprises a silver conductive layer, a carbon-based positive temperature coefficient layer and a dielectric protective layer. It is printed on TPU, cut out, laminated onto the textile, then covered with an extra laminated TPU layer for protection. The same heating approach has been used in undergarments, bags for battery transportation and composites for drone de-icing.

A specially developed positive temperature coefficient ink limits the heater to around 42–43°C, so it cannot get hotter and hurt the wearer. Under an IR camera the heater's behaviour is visible, and the power-versus-voltage curve shows the PTC characteristic: as it heats, the curve flattens out and it cannot heat further. This is described as built-in security.

The bigger challenge was robustness and wash cycles: small test structures were not the same as a large piece of clothing with a big heating element and many different materials, including carbon. The reported result is a product that can at least survive up to 50 washes, addressing that gap between small test structures and garment-scale printed heaters.

In this short video, you can learn:
* The heater stack uses silver, carbon-based PTC and dielectric layers printed on TPU, laminated onto textile with an extra TPU cover.
* The PTC ink caps temperature at around 42–43°C, and the power-versus-voltage curve flattens as it heats.
* Garment-scale heaters survived up to 50 washes, which was harder than small test structures because of multiple materials including carbon.

📋 **Clip Abstract** A printed TPU-laminated heater stack combines silver, carbon-based PTC and dielectric layers for textile heating. The PTC ink self-limits at 42–43°C, and a garment-scale version survived up to 50 washes.

About the speaker:
* Speaker: Zachary J. Davis
* Company: Danish Technological Institute
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#PrintedPTCHeater, #CarbonPTCInk, #TPULamination, #50WashDurability, #SmartTextiles, #PrintedElectronics

This is a highlight of the presentation:

Smart Wearables through Printed Electronics

Electronic Textiles RESHAPED 2026 | Berlin

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

03:28 - 04:58

Can you screen-print silver, dielectric and carbon stacks on PET, then heat-press them onto textile?

Can you screen-print silver, dielectric and carbon stacks on PET, then heat-press them onto textile?

The line runs a standard PET foil as the transfer carrier. Silver, dielectrics, carbon and other materials are deposited by screen print to build up the full electronic stack that will eventually sit on the textile. Each deposition passes into the oven and out the other side, and components typically carry quite a lot of printed layers before the stack is complete.

The last layer in the stack is usually an adhesive. It can be printed, like the silver, dielectrics and carbon below it, or deposited in another way. That adhesive is what performs the transfer: the printed component is bonded to the fabric, and the foil is no longer needed once the bond is made.

Transfer itself is simple. The foil is placed on top of the textile and given a very short heat press, a standard textile process found more or less anywhere. When it cools, the sheet is ripped off and all of the printed layers come away onto the textile. Very satisfying, and the whole stack moves at once.

In this short video, you can learn:
* Silver, dielectric and carbon materials are screen printed in multiple layers onto a standard PET transfer foil to build the component stack.
* The last printed layer is usually an adhesive, which can be printed or deposited another way and carries out the transfer.
* A very short heat press, a standard textile process, followed by ripping off the sheet moves all printed layers onto the fabric.

📋 **Clip Abstract** Printed electronics reach fabric through a standard PET transfer foil: silver, dielectric and carbon layers are screen printed and oven-cured, capped with an adhesive layer. A very short heat press and a peel then move the complete printed stack from foil to textile, using a process already standard in textiles.

About the speaker:
* Speaker: Zachary J. Davis
* Company: Danish Technological Institute
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#PetTransferFoil, #ScreenPrintDeposition, #PrintedAdhesiveLayer, #HeatPressTransfer, #ElectronicTextiles, #PrintedElectronics

05:30 - 07:19

Which printed ink and TPU stacks actually survive 50 wash cycles?

Which printed ink and TPU stacks actually survive 50 wash cycles?

Testing follows IPC standards as closely as possible: mechanical stretch and bending, wash testing, and abrasion testing such as Martindale, which asks whether printed structures wear off. They do not wear off. Wash testing is described as one of the most rigorous and most challenging tests in the arsenal.

Washing is not just water and detergent; a cycle of roughly 45 minutes to an hour applies substantial mechanical stretching and bending, so it is a lot of destructive forces. The data is plotted as resistance change versus number of wash cycles, and customers typically want at least 50 wash cycles.

Test structures combine silver ink, dielectric inks protecting it, and TPU on top. Every combination the team could find was built from purchased inks and TPUs. Many combinations work very poorly, but quite a few worked very well — essential if this is to be sold as a technology in a product; you cannot live with the poor performers.

In this short video, you can learn:
* Wash testing ranks among the most challenging tests because a 45-to-60-minute cycle combines water and detergent with substantial mechanical stretching and bending.
* Martindale abrasion testing confirmed that the printed structures do not wear off.
* Screening purchased silver inks, dielectric inks and TPUs across many stack combinations showed some working very poorly while quite a few worked very well against the 50-wash-cycle target customers ask for.

📋 **Clip Abstract** Wash testing at 45 minutes to an hour per cycle combines detergent with mechanical stretching and bending, tracked as resistance change versus wash cycles against a customer expectation of at least 50 cycles. Screening many silver ink, dielectric and TPU stack combinations showed some failing badly and several performing very well, alongside Martindale abrasion results where printed structures do not wear off.

About the speaker:
* Speaker: Zachary J. Davis
* Company: Danish Technological Institute
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#SilverInkStacks, #DielectricEncapsulation, #MartindaleAbrasion, #WashCycleTesting, #PrintedElectronics, #StretchableElectronics


Other talks by Zachary J. Davis

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page