Zikulnig Johanna | Silicon Austria Labs GmbH: Does switching to a bio-based substrate really cut a printed sensor's carbon footprint?
09:53 - 11:37
Other snippets from this talk
Summary of the clip:
Does switching to a bio-based substrate really cut a printed sensor's carbon footprint?
At raw material extraction, bio-based materials carry carbon uptake that is accumulated and stored in organic material as it grows. Taking such material can show a negative impact because growth stores CO2 used to build the structure. The net impact is production impact minus this carbon uptake for substrate materials. PLA is pretty intense in production, yet its carbon uptake is high, so the net impact becomes much lower.
The effect is even more extreme for a biop: its global warming potential in production is pretty low, and with all the carbon uptake it results in a negative impact at this stage. By contrast, PT has no carbon uptake, so for net impact at the raw material stage PT looks worse. However, that comparison is only for this stage viewed in isolation.
So the raw material stage alone can favor bio-based substrates, but isolation matters. PLA has intense production offset by high carbon uptake. A biop can reach negative impact here because production GWP is low and carbon uptake is counted. PT lacks carbon uptake, so it looks worse at this isolated raw-material stage. That does not settle other stages, because this is just this stage in an isolated way and net impact depends on production minus uptake.
In this short video, you can learn:
* Bio-based substrate materials accumulate and store carbon uptake, which can lead to a negative impact at raw material extraction.
* Net impact is production impact minus carbon uptake for substrate materials.
* PLA is production-intensive but high carbon uptake lowers its net impact, while PT has no carbon uptake and looks worse at the isolated raw-material stage.
📋 **Clip Abstract** The raw material extraction phase for substrate materials is assessed under life cycle assessment. Bio-based materials can show negative impact from carbon uptake and lower net impact, while PT without carbon uptake looks worse at this isolated stage.
About the speaker:
* Speaker: Zikulnig Johanna
* Company: Silicon Austria Labs GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#BioBasedSubstrates, #CarbonUptake, #RawMaterialExtraction, #NetImpactCalculation, #LifeCycleAssessment, #PrintedElectronics
This is a highlight of the presentation:
Life Cycle Assessment of Printed Electronics: Challenges, Insights and Opportunities
More Highlights from the same talk.
12:10 - 13:36
How uncertain is a chip's carbon footprint when fabs refuse to share LCA data?
How uncertain is a chip's carbon footprint when fabs refuse to share LCA data?
Plastics have good environmental-impact data because the plastics industry supplies it. Electronics differs: attempts to obtain LCA data from the chip manufacturer had no chance. The assessment therefore used literature-based assumptions. Studies compare greenhouse gas emission intensities for different fabs in kilograms CO2 equivalent per wafer square meter. The average is around 9,800, yet the minimum-to-maximum span is huge, already creating major data uncertainty.
Despite that uncertainty, assumptions are still needed. The calculation can use wafer size, area per wafer, die per wafer—information obtained from the manufacturer—and the rejection rate. From these inputs, the result is an approximation of 22.3 grams CO2 equivalent per one functional unit, meaning one chip. The huge fab-intensity span remains, so the chip-level number carries propagated uncertainty rather than measured fab data.
The comparison shows fab greenhouse-gas intensities vary widely around 9,800 kilograms CO2 equivalent per wafer square meter, so even an average assumption is weak. Combining wafer geometry, die count, and rejection rate yields 22.3 grams CO2 equivalent per chip, but this is an approximation. The data gap means the uncertainty must be mentioned, because plastics data quality is not matched in electronics LCA.
In this short video, you can learn:
* Plastics LCA data are abundant because industry supplies them, while chip-manufacturer LCA data were unavailable and literature assumptions were required.
* Across different fabs, greenhouse-gas emission intensity averages about 9,800 kg CO2 equivalent per wafer square meter but spans a huge minimum-to-maximum range.
* Using wafer size, area per wafer, die per wafer and rejection rate gives an approximation of 22.3 g CO2 equivalent per functional unit, one chip, with uncertainty noted.
📋 **Clip Abstract** LCA data for electronics are far harder to obtain than for plastics, so chip-level assessment relies on literature assumptions. Studies show fab greenhouse-gas intensities average about 9,800 kg CO2 equivalent per wafer square meter with a huge min-to-max span, and combining wafer geometry and rejection rate yields an approximate 22.3 g CO2 equivalent per chip.
About the speaker:
* Speaker: Zikulnig Johanna
* Company: Silicon Austria Labs GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#ChipLCADataGap, #FabEmissionIntensity, #WaferSquareMeter, #ChipCarbonFootprint, #PrintedElectronics, #SustainableElectronics
26:57 - 29:26
How much silver and copper is lost when printed electronics go to municipal incineration?
How much silver and copper is lost when printed electronics go to municipal incineration?
At municipal incineration, no energy is recovered from printed electronics because the metallic parts simply melt. Unburnable solids descend into the bottom ash, while filtered emissions are not the main concern for these components. Recovery from bottom ash focuses on native metal pieces larger than two millimeters in diameter, which is considered economical. Smaller metallic components from printed electronics devices are not recovered, so the silver, gold and copper they contain are effectively lost.
Bottom ash is either landfilled or used in the construction industry, commonly as a substitution for sand in concrete production. The transcript shows a melted aluminum piece recovered from bottom ash, but it remains molten with other waste and ash components. Recovering smaller pieces is not economical. Consequently, the metallic components of printed electronics devices are more or less lost, and their silver, gold and copper content is not recovered. This highlights the material fate in municipal waste incineration.
Switzerland incinerates 3.3 tons of silver nanoparticles per year at present, and those nanoparticles have a worth of 2.8 million euros. Silver nanoparticles are not only in printed electronics; they also appear in disinfectant sanitizers and other cosmetic products. Switzerland is small, so this figure represents just one country. The talk notes approaches to recover metals from bottom ash, yet the smaller metallic fractions from printed electronics are not economically recoverable under the two-millimeter diameter criterion.
In this short video, you can learn:
* Native metal pieces larger than two millimeters in diameter are considered economical to recover from incineration bottom ash, while smaller pieces are not.
* Metallic components from printed electronics devices, including silver, gold and copper, are effectively lost during municipal incineration.
* Switzerland incinerates 3.3 tons of silver nanoparticles annually, worth 2.8 million euros, with sources beyond printed electronics such as disinfectant sanitizers and cosmetics.
📋 **Clip Abstract** Municipal incineration melts metallic parts from printed electronics, sending unburnable solids to bottom ash where only native metal pieces above two millimeters are economical to recover. Bottom ash is landfilled or reused as sand substitute in concrete, while 3.3 tons of silver nanoparticles incinerated annually in Switzerland, worth 2.8 million euros, show the scale of lost material value.
About the speaker:
* Speaker: Zikulnig Johanna
* Company: Silicon Austria Labs GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#BottomAshRecovery, #SilverNanoparticleIncineration, #NativeMetalRecovery, #ConcreteSandSubstitution, #PrintedElectronics, #LifeCycleAssessment
16:22 - 18:23
Can printing method and grid carbon intensity dominate a printed sensor's manufacturing footprint?
Can printing method and grid carbon intensity dominate a printed sensor's manufacturing footprint?
The LCA discussion stresses that CO2 equivalent remains and that energy intensity varies widely with the energy mix. Geographical scope must therefore be defined, documented and explained. Austria, Sweden, the European Union average and Germany illustrate the issue; Germany has four times higher emission intensity than Austria despite neighbouring, similar production sites. The choice was to settle for the European Union average because geographical scope must be reflected and documented in the LCA study.
For printing methods, a huge peak appears for the aerosol check printer. It shows the highest global warming potential because of its slow throughput and high power demand. For large-size structures such as the antenna and many electrodes, aerosol chart is not the method to go with. This highlights avoiding over-engineering and choosing manufacturing methods aligned with application resolution and area requirements to minimise costs and environmental impact.
An opportunity is also identified because of the carbon intensity of the electricity. That connects to the earlier warning that energy intensity depends on the energy mix and that geographical scope must be documented and explained. The aerosol check printer's huge peak reinforces that application requirements, resolution and area should drive manufacturing choices, not over-engineering, to minimise costs and environmental impact.
In this short video, you can learn:
* LCA results are sensitive to geographical scope and energy mix, with Germany showing four times higher emission intensity than Austria despite neighbouring production sites.
* The aerosol check printer had the highest global warming potential due to slow throughput and high power demand, making it unsuitable for large antennas and many electrodes.
* Choosing printing methods aligned with application resolution and area requirements can avoid over-engineering and reduce costs and environmental impact.
📋 **Clip Abstract** The clip shows why geographical scope and energy mix must be defined, documented and explained in life cycle assessment, comparing Austria, Sweden, the European Union average and Germany. It then examines printing methods, where aerosol check printing has the highest global warming potential from slow throughput and high power demand, and notes an opportunity in the carbon intensity of electricity.
About the speaker:
* Speaker: Zikulnig Johanna
* Company: Silicon Austria Labs GmbH
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#LifeCycleAssessment, #GlobalWarmingPotential, #AerosolCheckPrinter, #EUEnergyMix, #PrintedElectronics, #SustainableElectronics
Links to this speaker's talk page and other highlights appear here.


