Alan Brown | Nagase ChemteX: Why is silver at a 40-year high, and how does a low-silver ink cut cost?
10:50 - 12:48
Other snippets from this talk
Summary of the clip:
Why is silver at a 40-year high, and how does a low-silver ink cut cost?
Silver has risen more than 70% per troy ounce since April, trading near $52.36 and reaching a 40-year high, which directly raises the cost of silver-containing inks. The comparison is a typical PTF conductor versus CI 1210, a low-cost conductive ink. CI 1210 uses significantly less silver and incorporates a low-cost composite material. That change shifts the cost structure before printing, but it also changes the electrical specification that the application must accept.
CI 1210 is specified at less than 25 per square per mil, while batch history shows 15 to 20; QC holds the specification below 25. It also delivers higher coverage than a typical PTF conductor, so the ink goes further when printed, saving money. Higher percent solids and higher print thickness support that coverage. These properties matter because resistivity and coverage together determine how much ink is needed for a target resistance.
The trade-off is explicit: the application must be able to sacrifice a little resistivity. If you have to print the same amount of ink to get the same resistance as a PTF conductor, you will probably lose the cost advantage of CI 1210. The preferred use case is therefore an application that can accept higher resistivity in exchange for lower silver content, lower material cost and less ink consumption. Otherwise, the low-silver formulation cannot beat the PTF conductor on total cost.
In this short video, you can learn:
* Silver is up over 70% per troy ounce since April, near $52.36 and at a 40-year high, raising silver-ink costs.
* CI 1210 uses significantly less silver and a low-cost composite material, with resistivity specified below 25 per square per mil and batch history of 15 to 20.
* Higher coverage, higher percent solids and higher print thickness let CI 1210 go further, but it only saves cost if the application can sacrifice some resistivity.
š **Clip Abstract** Silver's 40-year high and more than 70% rise since April make silver-containing inks expensive, so CI 1210 replaces much of the silver with a low-cost composite. Its below-25 per-square-per-mil specification, higher coverage and higher solids reduce ink use, but the cost advantage depends on an application that can sacrifice a little resistivity.
About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
šļø Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#CI1210, #PTFConductor, #SilverTroyOunce, #ResistivityPerMil, #PrintedElectronics, #ConductiveInks
This is a highlight of the presentation:
Selecting Conductive Inks: A Property-Driven Approach for Printed Electronics Applications
More Highlights from the same talk.
05:42 - 08:00
Why can the same stretchable ink fail on one TPU and work on another, and which circuit pattern keeps it conductive?
Why can the same stretchable ink fail on one TPU and work on another, and which circuit pattern keeps it conductive?
Substrate versus stretch comes down to pairing: the right ink combination with the right TPU combination. Many TPUs are on the market and each can perform differently with the same ink, so the starting point is the elongation your application actually needs, then whether the ink meets it. A TPU that appears to stretch further may simply fit different parameters and remain a valid option.
Processing is the next gate. These are conventional screen-printed inks, and general processing runs at 120 to 130 °C to reach optimum resistivity values. The critical parameter is whether the TPU can be processed at those temperatures and maintain dimensional stability. If the TPU is later transferred to a garment or another fabric, the transfer temperature the TPU needs is a further consideration.
Circuit design then changes the stretchability of the ink itself. The straight-line pattern shows the exponential curve of resistance rise, while the sinusoidal and the ohm patterns far outperform on percent stretch versus resistivity. Like a Slinky, those geometries alleviate stress in the pattern and reduce resistance increase as the material stretches further ā the earlier CI1036 result was cited as about a 40% significant increase.
In this short video, you can learn:
* Identical ink can perform differently on different TPUs, so the elongation required by the application must be defined before the ink is selected.
* Conventional screen-printed inks need 120 to 130 °C processing to reach optimum resistivity, which makes TPU dimensional stability a critical filter.
* Sinusoidal and ohm-shaped circuit patterns act like a Slinky to alleviate stress and cut the resistance rise under stretch compared with a straight line.
š **Clip Abstract** Stretchable e-textile inks are a pairing problem: the same screen-printed ink behaves differently across TPUs, so application elongation, the 120 to 130 °C processing window and garment transfer temperature constrain selection. Sinusoidal and ohm circuit geometries, working like a Slinky, limit the resistance rise a straight-line trace suffers under stretch.
About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
š
Save the date: 20 and 21 October 2027
š Berlin, Germany
š Info: https://www.techblick.com/electronictextilesreshaped
#ScreenPrintedInk, #ThermoplasticPolyurethane, #SinusoidalCircuitPattern, #DimensionalStability, #ElectronicTextiles, #StretchableElectronics
09:44 - 12:02
Which stack-up survives IEC washing longer: silver-on-carbon, or carbon-silver-carbon, and at what resistance increase?
Which stack-up survives IEC washing longer: silver-on-carbon, or carbon-silver-carbon, and at what resistance increase?
Washability testing tracks resistance change per wash cycle, circuit construction and test temperature. The baseline stack-up places silver on top of carbon; the alternative sandwiches silver between two carbon layers. Testing followed IEC wash standards against a specified target of less than 150% resistance increase, or two and a half times. The construction of the circuit matters, not just the ink.
Initially, only the carbon-silver-carbon tri-sandwich stack-up was successful up to 20 washes, using the current CI1036 material. The next-generation CI1096 material, shown as the bottom blue line, reached up to 50 wash cycles. Both results use a TPU film with carbon, silver, carbon. The sandwiching of silver is important in the circuit construction.
Substrate choice can produce significant performance differences even when moving from one TPU film to another TPU film. Those films have different moisture permeability properties. For wearable washability, the relevant questions include resistance change with each wash cycle, how the circuit is constructed, and the temperature used for testing. Performance over 50 or 100 wash cycles must be assessed against the specified resistance-increase target.
In this short video, you can learn:
* The specified washability target was less than 150% resistance increase, equal to two and a half times.
* The carbon-silver-carbon tri-sandwich with CI1036 was successful up to 20 washes under IEC wash standards.
* The next-generation CI1096 material reached up to 50 wash cycles on TPU film with carbon, silver, carbon.
š **Clip Abstract** This clip compares a silver-on-carbon stack-up with a carbon-silver-carbon sandwich for washable electronic textiles. It reports IEC wash testing against a less-than-150% resistance-increase target, with CI1036 reaching 20 washes and next-generation CI1096 reaching 50 cycles, while noting TPU moisture-permeability differences.
About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
š
Save the date: 20 and 21 October 2027
š Berlin, Germany
š Info: https://www.techblick.com/electronictextilesreshaped
#CarbonSilverCarbonSandwich, #IECWashStandard, #CI1096, #TPUMoisturePermeability, #ElectronicTextiles, #WearableElectronics
07:54 - 09:50
How much does next-generation silver ink reduce resistance rise and recover after repeated stretching?
How much does next-generation silver ink reduce resistance rise and recover after repeated stretching?
The CI1096 is positioned as a next-generation silver ink, benchmarked directly against the CI1036 legacy product on a resistance-versus-stretch chart. Both formulations show very good stretch properties, but the CI1096 delivers less of a change in resistance, which the speaker says makes the design engineer's job easier when laying out stretchable circuits. A second chart shows the newer ink recovering very well as it returns to its original positioning.
Cycle testing shown here covers only five cycles with the CI1096, with a slight increase expected over time. The substrate was Elecom stretch white: 7.44 inches initial length, 7.7 inches final. The speaker stresses the ink is not increasing in resistance greatly ā a longer trace from substrate elongation raises resistance slightly anyway, not significantly. This shows very good repeatability of stretch properties under cycling.
The trade-off is explicit: the legacy CI1036 already offers very good stretch properties, but the next-generation CI1096 narrows the resistance change and returns closer to its original positioning after stretching. For designers, that smaller swing makes designing these circuits a little easier. The speaker notes that stretch performance with these inks, particularly as applications get more demanding, remains one of the main areas of focus.
In this short video, you can learn:
* CI1096 shows a smaller resistance change under stretch than the legacy CI1036, while both retain very good stretch properties.
* Five-cycle testing on Elecom stretch white moved substrate length from 7.44 to 7.7 inches, producing only a slight resistance rise.
* Part of the measured resistance increase is geometric, from the longer trace, rather than the ink itself degrading.
š **Clip Abstract** The CI1096 next-generation silver ink is compared with the legacy CI1036, showing a smaller resistance change under stretch and strong recovery toward the original position. Five-cycle testing on Elecom stretch white substrate, from 7.44 to 7.7 inches, produced only a slight resistance rise attributed largely to the longer trace rather than ink degradation.
About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Electronic Textiles RESHAPED 2027 | Berlin
š
Save the date: 20 and 21 October 2027
š Berlin, Germany
š Info: https://www.techblick.com/electronictextilesreshaped
#SilverInkStretchRecovery, #ResistanceRecovery, #StretchWhiteSubstrate, #FiveCycleStretchTest, #ElectronicTextiles, #StretchableElectronics
Other talks by Alan Brown
- Stretchable, Wearable and Washable Inks: Meeting the Requirements for Next-Generation Electronic Textiles Ā· Electronic Textiles RESHAPED 2026 Berlin
- Conductive Ink Selection for Medical Electronics: Critical Material Properties Ā· TechBlick Innovations Festival July 2026
- Conductive Inks for Medical/ Wearable Electronics Ā· Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- Next Generation Stretchable Conductive Ink Ā· The Future of Electronics RESHAPED 2025 USA
- Conductive Inks for Wearable/ Stretchable Electronics Ā· The Future of Electronics RESHAPED 2024 Berlin
- Conductive Ink Wash Testing Ā· TechBlick Innovations Festival | Free-To-Attend 2024
- Recent Developments of Conductive Inks for Printed Electronics Ā· Innovations Festival: Printed, Flexible, Hybrid, 3D, Wearable, & Textile Electronics 2023
- Recent Trends of Conductive Inks for Printed Electronics Ā· Printed, Hybrid, InMold, and 3D Electronics 2022
More highlights from Alan Brown
- ā¶ Why can the same stretchable ink fail on one TPU and work on another, and which circuit pattern keeps it conductive? Ā· Electronic Textiles RESHAPED 2026 | Berlin
- ā¶ How much does next-generation silver ink reduce resistance rise and recover after repeated stretching? Ā· Electronic Textiles RESHAPED 2026 | Berlin
- ā¶ Which stack-up survives IEC washing longer: silver-on-carbon, or carbon-silver-carbon, and at what resistance increase? Ā· Electronic Textiles RESHAPED 2026 | Berlin
- ā¶ How does the silver-to-binder ratio affect the overall performance of stretchable conductive inks? Ā· The Future of Electronics RESHAPED USA | Boston 2025
- ā¶ How does line trace width impact the durability of conductive inks under repeated creasing? Ā· The Future of Electronics RESHAPED USA | Boston 2025
- ā¶ What is the impact of a carbon-silver-carbon tri-layer structure on the washability of conductive inks on TPU substrates? Ā· The Future of Electronics RESHAPED USA | Boston 2025
- ā¶ How can you make printed electronics survive 20+ wash cycles? Ā· The Future of Electronics RESHAPED 2024
- ā¶ Is your ink failing in the wash, or is it your substrate? Ā· The Future of Electronics RESHAPED 2024
- ā¶ Can you stretch a conductive trace to 100% elongation without its resistance skyrocketing? Ā· The Future of Electronics RESHAPED 2024


