top of page

Alan Brown

Nagase ChemteX

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Alan Brown | Nagase ChemteX: Can a low-cost composite ink beat a 100% silver PTF after 1,600 hours and 85/85 humidity?

13:23 - 15:48

Other snippets from this talk

Summary of the clip:

Can a low-cost composite ink beat a 100% silver PTF after 1,600 hours and 85/85 humidity?

The accelerated thermal cycle runs about five hours: a 30-minute ramp from 23 °C to −40 °C, a one-hour soak, then a ramp from −40 °C to 85 °C (the slide's 80 °C is a typo), a one-hour soak at 85 °C, and a ramp back to 23 °C. CI 1210 is covered with carbon ink for extra protection, though its leads stay exposed. After roughly 100 hours — about 20 cycles — the ink is exposed, and CI 1210 remains very stable.

The trade-off is a little extra resistivity compared with a conventional polymer thick film. The blue trace is a 100% silver PTF, which explains its lower value. The key takeaway is that CI 1210 stays consistent and level through cycling. Fast-forwarding to about 1,600 hours, CI 1210 is actually much more stable than the PTF ink — and 1,600 hours is well beyond what any application would generally require.

At 85 °C and 85% relative humidity — a critical test parameter for the low-cost composite — the material does not start to increase in resistance until 500 hours, and it does not exceed a 5% increase until after 750 hours. Based on this data, using CI 1210 in a real-world, primarily automotive application, you could expect a 20-year lifecycle. That headroom matters for qualification.

In this short video, you can learn:
* CI 1210 stays stable through roughly 20 cycles of a five-hour −40 °C to 85 °C thermal profile, even where the ink is exposed.
* At about 1,600 hours of cycling, CI 1210 is much more stable than the 100% silver PTF reference, trading only a little resistivity.
* In 85 °C/85% RH, resistance only rises after 500 hours and passes a 5% increase after 750 hours, supporting a 20-year automotive lifecycle estimate.

📋 **Clip Abstract** Data from a five-hour −40 °C to 85 °C thermal cycle shows CI 1210 holding stable to 100 hours, then outperforming a 100% silver PTF at 1,600 hours. Under 85 °C/85% RH it shows no resistance rise until 500 hours and stays under a 5% increase past 750 hours, supporting a 20-year automotive lifecycle.

About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#ConductiveInks, #ThermalCycling, #PolymerThickFilm, #SilverPTF, #PrintedElectronics, #AutomotiveElectronics

This is a highlight of the presentation:

Selecting Conductive Inks: A Property-Driven Approach for Printed Electronics Applications

The Future of Electronics RESHAPED 2025 | Berlin

​

22-23 October 2025

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

05:42 - 08:00

Why can the same stretchable ink fail on one TPU and work on another, and which circuit pattern keeps it conductive?

Why can the same stretchable ink fail on one TPU and work on another, and which circuit pattern keeps it conductive?

Substrate versus stretch comes down to pairing: the right ink combination with the right TPU combination. Many TPUs are on the market and each can perform differently with the same ink, so the starting point is the elongation your application actually needs, then whether the ink meets it. A TPU that appears to stretch further may simply fit different parameters and remain a valid option.

Processing is the next gate. These are conventional screen-printed inks, and general processing runs at 120 to 130 °C to reach optimum resistivity values. The critical parameter is whether the TPU can be processed at those temperatures and maintain dimensional stability. If the TPU is later transferred to a garment or another fabric, the transfer temperature the TPU needs is a further consideration.

Circuit design then changes the stretchability of the ink itself. The straight-line pattern shows the exponential curve of resistance rise, while the sinusoidal and the ohm patterns far outperform on percent stretch versus resistivity. Like a Slinky, those geometries alleviate stress in the pattern and reduce resistance increase as the material stretches further — the earlier CI1036 result was cited as about a 40% significant increase.

In this short video, you can learn:
* Identical ink can perform differently on different TPUs, so the elongation required by the application must be defined before the ink is selected.
* Conventional screen-printed inks need 120 to 130 °C processing to reach optimum resistivity, which makes TPU dimensional stability a critical filter.
* Sinusoidal and ohm-shaped circuit patterns act like a Slinky to alleviate stress and cut the resistance rise under stretch compared with a straight line.

📋 **Clip Abstract** Stretchable e-textile inks are a pairing problem: the same screen-printed ink behaves differently across TPUs, so application elongation, the 120 to 130 °C processing window and garment transfer temperature constrain selection. Sinusoidal and ohm circuit geometries, working like a Slinky, limit the resistance rise a straight-line trace suffers under stretch.

About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#ScreenPrintedInk, #ThermoplasticPolyurethane, #SinusoidalCircuitPattern, #DimensionalStability, #ElectronicTextiles, #StretchableElectronics

09:44 - 12:02

Which stack-up survives IEC washing longer: silver-on-carbon, or carbon-silver-carbon, and at what resistance increase?

Which stack-up survives IEC washing longer: silver-on-carbon, or carbon-silver-carbon, and at what resistance increase?

Washability testing tracks resistance change per wash cycle, circuit construction and test temperature. The baseline stack-up places silver on top of carbon; the alternative sandwiches silver between two carbon layers. Testing followed IEC wash standards against a specified target of less than 150% resistance increase, or two and a half times. The construction of the circuit matters, not just the ink.

Initially, only the carbon-silver-carbon tri-sandwich stack-up was successful up to 20 washes, using the current CI1036 material. The next-generation CI1096 material, shown as the bottom blue line, reached up to 50 wash cycles. Both results use a TPU film with carbon, silver, carbon. The sandwiching of silver is important in the circuit construction.

Substrate choice can produce significant performance differences even when moving from one TPU film to another TPU film. Those films have different moisture permeability properties. For wearable washability, the relevant questions include resistance change with each wash cycle, how the circuit is constructed, and the temperature used for testing. Performance over 50 or 100 wash cycles must be assessed against the specified resistance-increase target.

In this short video, you can learn:
* The specified washability target was less than 150% resistance increase, equal to two and a half times.
* The carbon-silver-carbon tri-sandwich with CI1036 was successful up to 20 washes under IEC wash standards.
* The next-generation CI1096 material reached up to 50 wash cycles on TPU film with carbon, silver, carbon.

📋 **Clip Abstract** This clip compares a silver-on-carbon stack-up with a carbon-silver-carbon sandwich for washable electronic textiles. It reports IEC wash testing against a less-than-150% resistance-increase target, with CI1036 reaching 20 washes and next-generation CI1096 reaching 50 cycles, while noting TPU moisture-permeability differences.

About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#CarbonSilverCarbonSandwich, #IECWashStandard, #CI1096, #TPUMoisturePermeability, #ElectronicTextiles, #WearableElectronics

07:54 - 09:50

How much does next-generation silver ink reduce resistance rise and recover after repeated stretching?

How much does next-generation silver ink reduce resistance rise and recover after repeated stretching?

The CI1096 is positioned as a next-generation silver ink, benchmarked directly against the CI1036 legacy product on a resistance-versus-stretch chart. Both formulations show very good stretch properties, but the CI1096 delivers less of a change in resistance, which the speaker says makes the design engineer's job easier when laying out stretchable circuits. A second chart shows the newer ink recovering very well as it returns to its original positioning.

Cycle testing shown here covers only five cycles with the CI1096, with a slight increase expected over time. The substrate was Elecom stretch white: 7.44 inches initial length, 7.7 inches final. The speaker stresses the ink is not increasing in resistance greatly — a longer trace from substrate elongation raises resistance slightly anyway, not significantly. This shows very good repeatability of stretch properties under cycling.

The trade-off is explicit: the legacy CI1036 already offers very good stretch properties, but the next-generation CI1096 narrows the resistance change and returns closer to its original positioning after stretching. For designers, that smaller swing makes designing these circuits a little easier. The speaker notes that stretch performance with these inks, particularly as applications get more demanding, remains one of the main areas of focus.

In this short video, you can learn:
* CI1096 shows a smaller resistance change under stretch than the legacy CI1036, while both retain very good stretch properties.
* Five-cycle testing on Elecom stretch white moved substrate length from 7.44 to 7.7 inches, producing only a slight resistance rise.
* Part of the measured resistance increase is geometric, from the longer trace, rather than the ink itself degrading.

📋 **Clip Abstract** The CI1096 next-generation silver ink is compared with the legacy CI1036, showing a smaller resistance change under stretch and strong recovery toward the original position. Five-cycle testing on Elecom stretch white substrate, from 7.44 to 7.7 inches, produced only a slight resistance rise attributed largely to the longer trace rather than ink degradation.

About the speaker:
* Speaker: Alan Brown
* Company: Nagase ChemteX America LLC
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#SilverInkStretchRecovery, #ResistanceRecovery, #StretchWhiteSubstrate, #FiveCycleStretchTest, #ElectronicTextiles, #StretchableElectronics


Other talks by Alan Brown


More highlights from Alan Brown

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page