Alan Wu | Smooth & Sharp: How do we completely eliminate toxic chemical etching and plastics from high-volume RFID antenna manufacturing?
00:08:24 - 00:09:40
Other snippets from this talk
Summary of the clip:
How do we completely eliminate toxic chemical etching and plastics from high-volume RFID antenna manufacturing?
Traditional RFID antenna fabrication is an environmental bottleneck, relying heavily on aluminum-PET laminates and subtractive acid etching. This presentation contrasts that conventional methodology with a direct-on-paper additive manufacturing flow. By printing conductive traces directly onto a paper carrier, the process bypasses toxic chemical waste, water consumption, and the plastic substrate entirely.
The hardware architecture utilized for this process adapts graphic printing machinery for electronic materials. It integrates screen, flexographic, and gravure printing heads inline with Near-Infrared (NIR) and photonic curing systems. Operating on a 300 mm wide web, the line can process materials continuously at 30 meters per minute.
This integrated manufacturing line is capable of producing up to 1 billion UHF antennas per year. The materials bill is stripped down to its bare essentials: just paper and a nano-silver conductive ink, demonstrating a highly optimized commercial footprint.
In this short video, you can learn:
* The comparative workflow between subtractive aluminum etching and direct-on-paper printing
* System integration of screen, flexo, and gravure heads with inline photonic curing
* Throughput calculations for producing 1 billion units annually on a 300mm web
📋 **Clip Abstract** The speaker outlines a sustainable, additive alternative to subtractive aluminum-foil etching for RFID antennas. By leveraging a multi-head graphic printing press with inline photonic curing, the system achieves massive annual throughput using only paper and nano-silver ink.
#PhotonicCuring, #NanoSilverInk, #PaperElectronics, #RollToRollPrinting, #PrintedElectronics, #RFIDManufacturing
This is a highlight of the presentation:
More Highlights from the same talk.
04:16 - 05:59
Which printing process best balances on-demand antenna design, ink availability and production speed?
Which printing process best balances on-demand antenna design, ink availability and production speed?
Starting from a single layer with one chip, the first decision is which printing process to use. Inkjet is excellent and on-demand: an engineer designs a new antenna and circuit in the morning, and by the afternoon a colleague can print it, run chip assembly and test it. The con side is that the process is very demanding, and the selectable conductors are very limited.
Screen printing is the most mature option — a process people have used for more than 1,000 years, since ancient China. The problem is that the speed is very slow. The advantage is that the conductive ink is easy to source, because this is a very mature printing solution, so material availability is not the constraint that inkjet and flexographic impose on the ink formulator.
Flexographic printing offers the fastest speed in production, but the conductive ink is also very limited — only silver can be used for flexographic at this moment. The second challenge is curing and sintering: hot air, UV, NIR and photonic approaches are all available, and each option brings its own trade-offs when qualifying a printed inlay.
In this short video, you can learn:
* Inkjet delivers the shortest design-to-test loop — an antenna and circuit designed in the morning can be printed, chip-assembled and tested the same afternoon — but its process window is very demanding and the conductor choice is very limited.
* Screen printing is the most mature route and the easiest to source conductive ink for, but its production speed is very slow.
* Flexographic gives the fastest production speed yet at this moment accepts only silver conductive ink, and curing and sintering still has to be chosen from hot air, UV, NIR or photonic.
📋 **Clip Abstract** For a single-layer, one-chip inlay, choosing a printing process is a trade-off between on-demand design, ink availability and speed. Inkjet wins on same-day design-to-test, screen printing on mature ink sourcing, and flexographic on speed — but only silver is usable there today, and curing and sintering remain open.
About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#InkjetAntennaPrototyping, #ScreenPrintingConductiveInk, #FlexographicSilverInk, #PhotonicSintering, #PrintedElectronics, #FlexibleHybridElectronics
12:51 - 13:40
How do you reconcile high-speed roll-to-roll printing with millisecond ink sintering on paper?
How do you reconcile high-speed roll-to-roll printing with millisecond ink sintering on paper?
The starting point is a direct contradiction: production speed and ink curing or sintering time pull against each other. High speed creates high output, but the ink cannot be cured or sintered properly. Slow the line down and the ink cures or sinters better, yet the low output costs a higher production cost. Speed and ink quality sit at opposite ends of the same dial.
The substrate narrows the window further. If a low-temperature substrate such as paper is used, the paper could be carbonized by NIR. That rules out the straightforward high-energy sintering route on the very material that makes the inlay cheap. The temperature ceiling imposed by paper and the energy needed to sinter ink are therefore in direct conflict on the same web.
The photocuring tool solves this incompatibility perfectly. Ink is cured or sintered within milliseconds, and that keeps the machine running at a reasonable production speed rather than being throttled back to protect the ink. In some products the line runs smoothly, which is what makes printed RFID inlay at mass-production scale a workable basis for further FHE products.
This is a scheduling problem turned into a materials problem: the cure event is compressed into milliseconds so the web never has to slow down for the ink, and the paper never sees the thermal dose that would carbonize it. The photocuring tool is the interface between those two requirements.
In this short video, you can learn:
* High speed gives high output but leaves the ink improperly cured or sintered, while low speed improves cure or sinter at the cost of higher production cost.
* Using a low-temperature substrate such as paper exposes it to carbonization by NIR, closing the conventional high-energy sintering route.
* A photocuring tool cures or sinters the ink within milliseconds, keeping the machine at a reasonable production speed.
📋 **Clip Abstract** Production speed and ink curing or sintering time are contradictory, and slowing the line to protect the ink raises production cost. Photocuring cures or sinters the ink within milliseconds, so the machine holds a reasonable production speed even on paper that NIR would carbonize.
About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#PhotocuringSintering, #MillisecondCure, #PaperSubstrate, #PrintedRFIDInlay, #PrintedElectronics, #FlexibleHybridElectronics
09:01 - 10:07
How many papers, inks and chips were tested to qualify direct-on-paper RFID for mass production?
How many papers, inks and chips were tested to qualify direct-on-paper RFID for mass production?
The direct-on-paper program began in 2015, and the team framed the problem as finding a combination between material and process. Over the years it used more than 20 tons of different paper from paper mills worldwide. That volume was part of qualifying paper as a substrate, not just selecting a grade, because the final solution depended on matching paper to the printing and assembly route.
The ink campaign covered more than 100 kilos from different ink suppliers and for different printing processes: flexo, inkjet and screen printing. Copper, carbon, micro silver and nano silver were all tested. This was not a single ink screen; the work compared conductive ink families against the process, because the paper-and-process combination had to hold after printing.
Antenna validation required chip assembly, so the team assembled close to 1 million RFID chips and components after printing different antennas. The chip was described as more important because the printed antenna only becomes a final result after assembly. Testing therefore linked antenna print quality to chip and component assembly, not to antenna inspection alone.
In this short video, you can learn:
* The qualification began in 2015 and used more than 20 tons of paper from mills worldwide to find a material-and-process combination.
* More than 100 kilos of conductive ink were tested across flexo, inkjet and screen printing, covering copper, carbon, micro silver and nano silver.
* Close to 1 million RFID chips and components were assembled after printing different antennas, because the chip test was the decisive final check.
📋 **Clip Abstract** From 2015, the direct-on-paper RFID effort qualified more than 20 tons of paper and more than 100 kilos of conductive ink across flexo, inkjet and screen printing. It then assembled close to 1 million RFID chips and components after printing different antennas, making chip assembly part of the mass-production qualification.
About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#DirectOnPaperRFID, #NanoSilverInk, #FlexoInkjetScreen, #RFIDChipAssembly, #PrintedElectronics, #FlexibleHybridElectronics
Other talks by Alan Wu
- A Proven R2R Production Solution of NFC Antenna · Electronics RESHAPED USA 2026
- How far can a RFID Antenna reach biodegradability by using additive manufacturing? The creation of worldwide first and the only ISO certified RFID antenna · The Future of Electronics RESHAPED | Berlin 2023
- A NFC Biosensor Test Stripe made with Reel-to-Reel Hybrid Electronics on the same Substrate · The Future of Electronics RESHAPED 2022
- Printed RFID inlay in Mass Production Scale as basis for further FHE product · Printed, Hybrid, Structural, & 3D Electronics 2021
More highlights from Alan Wu
- ▶ Why does putting conductive ink into a standard graphic printing press fail? · Future of Electronics RESHAPED USA 2026
- ▶ Can you print sub-micron conductive antennas directly onto paper at high speeds without burning the substrate? · Future of Electronics RESHAPED USA 2026
- ▶ Why is it practically impossible to scale an inkjet-printed antenna prototype directly to high-volume flexographic production? · Future of Electronics RESHAPED USA 2026
- ▶ Can a paper-based NFC antenna reliably harvest and deliver enough power to drive active silicon and micro-LED components? · The Future of Electronics RESHAPED 2023 Berlin
- ▶ Why is photonic sintering the ultimate enabler for high-speed printed electronics on thermally sensitive paper? · The Future of Electronics RESHAPED 2023 Berlin
- ▶ Which printing process best balances on-demand antenna design, ink availability and production speed? · Printed, Hybrid, Structural & 3D Electronics 2021
- ▶ How many papers, inks and chips were tested to qualify direct-on-paper RFID for mass production? · Printed, Hybrid, Structural & 3D Electronics 2021
- ▶ How do you reconcile high-speed roll-to-roll printing with millisecond ink sintering on paper? · Printed, Hybrid, Structural & 3D Electronics 2021


