top of page

Alan Wu

Smooth & Sharp Corporation

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Alan Wu | Smooth & Sharp Corporation: How many papers, inks and chips were tested to qualify direct-on-paper RFID for mass production?

09:01 - 10:07

Other snippets from this talk

Summary of the clip:

How many papers, inks and chips were tested to qualify direct-on-paper RFID for mass production?

The direct-on-paper program began in 2015, and the team framed the problem as finding a combination between material and process. Over the years it used more than 20 tons of different paper from paper mills worldwide. That volume was part of qualifying paper as a substrate, not just selecting a grade, because the final solution depended on matching paper to the printing and assembly route.

The ink campaign covered more than 100 kilos from different ink suppliers and for different printing processes: flexo, inkjet and screen printing. Copper, carbon, micro silver and nano silver were all tested. This was not a single ink screen; the work compared conductive ink families against the process, because the paper-and-process combination had to hold after printing.

Antenna validation required chip assembly, so the team assembled close to 1 million RFID chips and components after printing different antennas. The chip was described as more important because the printed antenna only becomes a final result after assembly. Testing therefore linked antenna print quality to chip and component assembly, not to antenna inspection alone.

In this short video, you can learn:
* The qualification began in 2015 and used more than 20 tons of paper from mills worldwide to find a material-and-process combination.
* More than 100 kilos of conductive ink were tested across flexo, inkjet and screen printing, covering copper, carbon, micro silver and nano silver.
* Close to 1 million RFID chips and components were assembled after printing different antennas, because the chip test was the decisive final check.

📋 **Clip Abstract** From 2015, the direct-on-paper RFID effort qualified more than 20 tons of paper and more than 100 kilos of conductive ink across flexo, inkjet and screen printing. It then assembled close to 1 million RFID chips and components after printing different antennas, making chip assembly part of the mass-production qualification.

About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#DirectOnPaperRFID, #NanoSilverInk, #FlexoInkjetScreen, #RFIDChipAssembly, #PrintedElectronics, #FlexibleHybridElectronics

This is a highlight of the presentation:

Printed RFID inlay in Mass Production Scale as basis for further FHE product

Printed, Hybrid, Structural & 3D Electronics 2021

​

11-12 May 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

04:16 - 05:59

Which printing process best balances on-demand antenna design, ink availability and production speed?

Which printing process best balances on-demand antenna design, ink availability and production speed?

Starting from a single layer with one chip, the first decision is which printing process to use. Inkjet is excellent and on-demand: an engineer designs a new antenna and circuit in the morning, and by the afternoon a colleague can print it, run chip assembly and test it. The con side is that the process is very demanding, and the selectable conductors are very limited.

Screen printing is the most mature option — a process people have used for more than 1,000 years, since ancient China. The problem is that the speed is very slow. The advantage is that the conductive ink is easy to source, because this is a very mature printing solution, so material availability is not the constraint that inkjet and flexographic impose on the ink formulator.

Flexographic printing offers the fastest speed in production, but the conductive ink is also very limited — only silver can be used for flexographic at this moment. The second challenge is curing and sintering: hot air, UV, NIR and photonic approaches are all available, and each option brings its own trade-offs when qualifying a printed inlay.

In this short video, you can learn:
* Inkjet delivers the shortest design-to-test loop — an antenna and circuit designed in the morning can be printed, chip-assembled and tested the same afternoon — but its process window is very demanding and the conductor choice is very limited.
* Screen printing is the most mature route and the easiest to source conductive ink for, but its production speed is very slow.
* Flexographic gives the fastest production speed yet at this moment accepts only silver conductive ink, and curing and sintering still has to be chosen from hot air, UV, NIR or photonic.

📋 **Clip Abstract** For a single-layer, one-chip inlay, choosing a printing process is a trade-off between on-demand design, ink availability and speed. Inkjet wins on same-day design-to-test, screen printing on mature ink sourcing, and flexographic on speed — but only silver is usable there today, and curing and sintering remain open.

About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#InkjetAntennaPrototyping, #ScreenPrintingConductiveInk, #FlexographicSilverInk, #PhotonicSintering, #PrintedElectronics, #FlexibleHybridElectronics

00:01:53 - 00:02:43

Can a paper-based NFC antenna reliably harvest and deliver enough power to drive active silicon and micro-LED components?

Can a paper-based NFC antenna reliably harvest and deliver enough power to drive active silicon and micro-LED components?

Evaluating the physical limits of flexible, printed RF substrates reveals a significant shift toward sustainable hybrid integration. In this segment, the speaker discusses how a highly optimized, miniature NFC antenna layout can harvest enough RF energy to power up to seven LEDs alongside a dual-interface NFC/UHF silicon chip. This level of power delivery and multi-protocol performance requires precise impedance matching and highly conductive printed traces.

To achieve this at commercial scale, the fabrication process employs high-speed roll-to-roll gravure printing on low-temperature substrates such as PET and paper. Gravure printing allows for exceptionally uniform deposition of conductive inks, which is crucial for maintaining low series resistance in energy-harvesting loops.

The technical achievement lies in achieving a 150-micron line gap while running the web at a continuous speed of 30 meters per minute. This throughput demonstrates that additive graphic printing techniques can match the fine-pitch requirements traditionally reserved for photolithography and chemical etching.

In this short video, you can learn:
* The power-harvesting limits of modern micro-NFC antenna designs driving active components
* Line-gap scaling down to 150 microns using continuous gravure printing
* Substrate flexibility spanning low-temperature PET to standard paper

📋 **Clip Abstract** This clip highlights the transition from traditional rigid PCBs to ultra-thin, flexible NFC and UHF dual-interface antennas printed directly on paper and PET. It details how gravure roll-to-roll printing achieves a 150-micron resolution at 30 meters per minute to support power-harvesting applications.

#R2RGravurePrinting, #RFPowerHarvesting, #PaperBasedElectronics, #PrintedNFCAntenna, #FlexibleHybridElectronics, #SmartPackaging

12:51 - 13:40

How do you reconcile high-speed roll-to-roll printing with millisecond ink sintering on paper?

How do you reconcile high-speed roll-to-roll printing with millisecond ink sintering on paper?

The starting point is a direct contradiction: production speed and ink curing or sintering time pull against each other. High speed creates high output, but the ink cannot be cured or sintered properly. Slow the line down and the ink cures or sinters better, yet the low output costs a higher production cost. Speed and ink quality sit at opposite ends of the same dial.

The substrate narrows the window further. If a low-temperature substrate such as paper is used, the paper could be carbonized by NIR. That rules out the straightforward high-energy sintering route on the very material that makes the inlay cheap. The temperature ceiling imposed by paper and the energy needed to sinter ink are therefore in direct conflict on the same web.

The photocuring tool solves this incompatibility perfectly. Ink is cured or sintered within milliseconds, and that keeps the machine running at a reasonable production speed rather than being throttled back to protect the ink. In some products the line runs smoothly, which is what makes printed RFID inlay at mass-production scale a workable basis for further FHE products.

This is a scheduling problem turned into a materials problem: the cure event is compressed into milliseconds so the web never has to slow down for the ink, and the paper never sees the thermal dose that would carbonize it. The photocuring tool is the interface between those two requirements.

In this short video, you can learn:
* High speed gives high output but leaves the ink improperly cured or sintered, while low speed improves cure or sinter at the cost of higher production cost.
* Using a low-temperature substrate such as paper exposes it to carbonization by NIR, closing the conventional high-energy sintering route.
* A photocuring tool cures or sinters the ink within milliseconds, keeping the machine at a reasonable production speed.

📋 **Clip Abstract** Production speed and ink curing or sintering time are contradictory, and slowing the line to protect the ink raises production cost. Photocuring cures or sinters the ink within milliseconds, so the machine holds a reasonable production speed even on paper that NIR would carbonize.

About the speaker:
* Speaker: Alan Wu
* Company: Smooth & Sharp Corporation
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#PhotocuringSintering, #MillisecondCure, #PaperSubstrate, #PrintedRFIDInlay, #PrintedElectronics, #FlexibleHybridElectronics


About this talk

→ Printed RFID inlay in Mass Production Scale as basis for further FHE product · Alan Wu · Printed, Hybrid, Structural, & 3D Electronics 2021


Other talks by Alan Wu


More highlights from Alan Wu

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page