Boris Forsthuber | Holzforschung Austria: How can printed strain sensors be integrated into structural timber beams to monitor mechanical stress?
02:48 - 04:37
Other snippets from this talk
Summary of the clip:
How can printed strain sensors be integrated into structural timber beams to monitor mechanical stress?
Strain sensors were printed directly onto small wood samples, then read out two ways: a Wheatstone bridge and four-wire measurements, with both performing similarly well. A stepwise load function was applied to the printed sample, and the measured value changed with each load step, exactly as expected. The slide shows the same printed strain sensor from a different angle, confirming the printed gauge tracks the applied mechanical load.
The samples are small, but the approach scales: the same printing route is applied to much larger wood elements. A tensile testing machine described as one of the largest in Austria and in Europe, built specifically for building products and rated at 100 tons of power, carries a very large printed strain gauge on top of the wood. As the speaker puts it, it can tear things apart.
The target is a sensor inside a timber beam, not on a lab coupon. These beams are built up from several layers of wood, and the printed strain sensors are already included inside such a beam, the basis for a smart product, a smart beam. That enables a very new application, in a project the speaker currently leads.
In this short video, you can learn:
* Printed strain sensors on wood performed similarly well whether read out with a Wheatstone bridge or with four-wire measurements.
* A stepwise loading function produced the expected change in the printed sensor signal, step by step.
* Sensors printed on small wood coupons are being transferred to full-size timber beams built from several wood layers and tested on a 100-ton tensile machine.
π **Clip Abstract** Printed strain sensors applied directly to wood track stepwise mechanical loading and read out comparably under Wheatstone bridge and four-wire configurations. The same printing approach scales from small coupons to very large gauges on wood, with sensors embedded in multi-layer timber beams to create smart structural products.
About the speaker:
* Speaker: Boris Forsthuber
* Company: Holzforschung Austria
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#PrintedStrainGauge, #WheatstoneBridge, #TimberBeams, #StepwiseLoadTest, #StructuralHealthMonitoring, #SmartWoodStructures
This is a highlight of the presentation:
EcoPCBs on Wood: Sustainable Printed Electronics on Wood
More Highlights from the same talk.
06:02 - 07:35
Why are wood veneers a lower-energy alternative to paper for printed electronics substrates?
Why are wood veneers a lower-energy alternative to paper for printed electronics substrates?
Paper is also just wood, so why bother with wood at all? Because turning wood into paper is energy- and chemical-hungry: logs are chipped, the chips are broken into fibres by a chemical process, then come sheet formation and drying. Every step is energy-intensive, and the route is complex and needs a lot of chemicals.
Peeling veneers for plywood is far easier. Logs are simply peeled, forming very long sheets of pure wood β the video shows 1.4 millimetres, but veneers can be made much thinner, down to 0.5 to 0.7 millimetres. No chemicals are needed, and the wood structure is preserved, which is quite great.
Wood is divided into softwood and hardwood, and it is composed of large voluminous cells running along the fibre axis. That makes the substrate very porous: very light, low density, but still very strong and stiff. So the veneer keeps its native cell architecture rather than being rebuilt from separated fibres.
In this short video, you can learn:
* Making paper from wood requires chipping, chemical fibre separation, sheet formation and drying, all energy-intensive steps.
* Peeling yields long sheets of pure wood with no chemicals, from 1.4 mm down to 0.5 to 0.7 mm.
* Voluminous wood cells along the fibre axis make the veneer porous and low-density while still strong and stiff.
π **Clip Abstract** Wood veneers skip the chipping, chemical fibre separation, sheet formation and drying that make paper so energy-intensive, replacing them with a simple peeling step that needs no chemicals. The preserved, porous cell structure along the fibre axis keeps the substrate very light and low-density while remaining strong and stiff.
About the speaker:
* Speaker: Boris Forsthuber
* Company: Holzforschung Austria
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#WoodVeneerSubstrate, #RotaryPeeledVeneer, #ChemicalFreeSubstrate, #VoluminousWoodCells, #SustainableElectronics, #PrintedElectronics
14:14 - 15:40
Why do low-cost wood veneers still yield printed PCBs costlier than commercial FR4 boards?
Why do low-cost wood veneers still yield printed PCBs costlier than commercial FR4 boards?
Veneer itself is not the cost barrier: it is a standard, low-cost wood product, among the cheapest wood products available. The expense sits in electronics production. These boards are not a standard product and are not made roll-to-roll as with paper; the process remains sheet-to-sheet. On that basis, the speaker assumes wood-veneer PCBs currently cost more than a commercial PCB, despite the lower carbon footprint.
There are many ideas for application, particularly in the wood industry, where the substrate already fits. A demonstrated use case is a moisture sensor for pocket flooring, integrated as an additional wood layer into an existing wood product. Commercialization is still early-stage applied research, however. Moving to a higher TRL requires many process steps, so the route from proof of concept to manufacturable wood-veneer electronics remains long.
The manufacturing bottleneck is the printed-electronics step, not veneer supply. Sheet-to-sheet handling prevents the roll-to-roll economics associated with paper, and the non-standard nature of the printed circuit keeps production costs high. Because the work remains at an early research stage with many required steps, scaling cannot yet be treated like established FR4 fabrication. The clip also raises whether significant sorting is needed after skiving veneer into sheets.
In this short video, you can learn:
* Veneer is a low-cost standard wood product, but printed-electronics production remains expensive because it is non-standard and sheet-to-sheet.
* A moisture sensor integrated as an extra wood layer in pocket flooring is a strong wood-industry use case, still at an early research stage.
* Reaching higher TRL requires many steps, and veneer sheet sorting after skiving is raised as an open process question.
π **Clip Abstract** The clip compares wood-veneer PCB economics with commercial boards: veneer is cheap and standard, but printed electronics remain non-standard and sheet-to-sheet, so production is assumed costlier than a commercial PCB. It also frames commercialization as early-stage research, with a pocket-flooring moisture sensor as a wood-industry use case and many steps still needed to raise TRL.
About the speaker:
* Speaker: Boris Forsthuber
* Company: Holzforschung Austria
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#WoodVeneerPCB, #SheetToSheetPrinting, #PocketFlooringMoistureSensor, #VeneerSkivingSorting, #SustainableElectronics, #PrintedElectronics
10:27 - 12:07
How do you build a functional 4-layer PCB on bio-based plywood using printed conductive tracks and tomato waste primer?
How do you build a functional 4-layer PCB on bio-based plywood using printed conductive tracks and tomato waste primer?
The final demonstrator is a four-layer plywood EcoPCB, described as the biggest challenge of the work, built as an impedance analyzer used mostly for moisture sensing. The top layer carries a digital section, an analog section and input/output for the impedance measurements; two ground layers sit in between and one bottom layer completes the stack.
Silver is printed on the substrate for the bottom, as for the top layer; the dark colour comes from the primer supplied by company partner Ada, a coating based on rutin β a waste product of tomato production. Two inner layers and the bottom layer are fully printed. Bio-based materials are good, residue-based ones even better.
Components were glued onto the wood surface mostly with ACA, sometimes also with ACF. Drilling and milling were done with a CNC machine; all vias were filled with ink by hand, which was quite a lot of work. It is a demonstrator for lab use, but it is very dense and works quite well.
In this short video, you can learn:
* The primer giving the printed silver its dark appearance is a rutin-based coating from tomato-production waste, supplied by partner Ada.
* Two inner ground layers and the bottom layer are fully printed, while the top layer is described as cramped and very busy.
* All vias were filled with ink by hand after CNC drilling and milling, and components were attached with ACA and ACF.
π **Clip Abstract** A four-layer plywood EcoPCB demonstrator works as an impedance analyzer for moisture sensing, combining printed silver layers with a rutin-based primer derived from tomato-production waste. Two fully printed inner ground layers, CNC drilling and milling, and hand-filled vias produce a dense lab demonstrator assembled with ACA and ACF.
About the speaker:
* Speaker: Boris Forsthuber
* Company: Holzforschung Austria
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#EcoPCB, #RutinPrimer, #SilverInkPrinting, #CNCViaFilling, #SustainableElectronics, #PrintedElectronics
About this talk
β EcoPCBs on Wood: Sustainable Printed Electronics on Wood Β· Boris Forsthuber Β· Sustainable Electronics RESHAPED 2026 Berlin


