Daisuke Hozumi | KYOCERA Europe: How does a 10-pulse drive cycle deliver 280 picoliters and stay stable for 5,000 seconds?
08:18 - 09:12
Other snippets from this talk
Summary of the clip:
How does a 10-pulse drive cycle deliver 280 picoliters and stay stable for 5,000 seconds?
Strobe imaging of a single nozzle shows how the printhead builds its target volume: ten ejection pulses are packed into one drive cycle, and the ejected drops are controlled to merge in pairs. The resulting 280 picoliters is a per-cycle figure, not the volume of an individual droplet.
Stability was measured at the nozzle rather than inferred from the print. Strobe imaging captured a single nozzle jetting at 3.5 kilohertz continuously for 5,000 seconds without losing the jet. That duration is the evidence base for claiming a repeatable, long-run ejection regime at this frequency.
Downstream, the printed samples show fine patterns with good reproduction, indicating the merge-in-pairs ejection scheme preserves feature definition. Hiding power was also maintained over a continuous print length of more than two meters, so optical coverage held across a long uninterrupted run rather than degrading as printing continued.
In this short video, you can learn:
* Ten ejection pulses per drive cycle are merged in pairs to reach 280 picoliters per cycle, not per droplet.
* A single nozzle jetted at 3.5 kilohertz for 5,000 seconds in the strobe-imaged stability test.
* Printed samples reproduced fine patterns, and hiding power held over more than two meters of continuous printing.
📋 **Clip Abstract** A ten-pulse drive cycle that merges ejected drops in pairs delivers 280 picoliters per cycle from a single nozzle. Strobe imaging confirms 3.5 kilohertz jetting stable for 5,000 seconds, with fine patterns reproduced and hiding power held past two meters of continuous printing.
About the speaker:
* Speaker: Daisuke Hozumi
* Company: KYOCERA Europe
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#HighViscosityInkjet, #PicoliterDropMerging, #StrobeImaging, #HidingPowerRetention, #PrintedElectronics, #AdditiveManufacturing
This is a highlight of the presentation:
Exploring Printed Electronics Applications of a Piezoelectric Bend‑Mode Inkjet Printhead for High‑Viscosity Inks
More Highlights from the same talk.
05:10 - 06:40
Why use water-based automotive paint to prove an 80 mPa·s high-viscosity printhead?
Why use water-based automotive paint to prove an 80 mPa·s high-viscosity printhead?
The printhead under development was evaluated with water-based automotive paint as a model fluid. Like some PE materials, the paint needs high-viscosity handling. Because it is shear-thinning, viscosity is specified at a shear rate of 1,000 per second; jetting was confirmed up to 80 mPa·s under that definition.
Automotive coating was selected to show why high-viscosity jetting matters. Conventional spray coating produces unwanted mist that must be collected, requiring large coating booths and substantial ventilation. In principle, inkjet could achieve 100% transfer efficiency, allowing smaller booths and reducing the energy needed for ventilation and air conditioning.
The figures on the slide are illustrative rather than measured results. Automotive coatings consist of several layers, each with a different function. For this study, the selected coating layer follows the explanation of why automotive coating was chosen; the paint remains the model fluid for evaluating the high-viscosity printhead.
In this short video, you can learn:
* Water-based automotive paint was used as a shear-thinning model fluid, with viscosity specified at a shear rate of 1,000 per second.
* Jetting was confirmed up to 80 mPa·s under that shear-rate definition for the high-viscosity printhead under development.
* Inkjet could in principle reach 100% transfer efficiency, unlike conventional spray coating that produces mist requiring large booths and substantial ventilation.
📋 **Clip Abstract** A high-viscosity printhead under development was evaluated using water-based automotive paint as a shear-thinning model fluid, with jetting confirmed up to 80 mPa·s at a specified shear rate of 1,000 per second. The automotive-coating example explains the motivation: conventional spray creates mist and requires large booths and ventilation, while inkjet could in principle achieve 100% transfer efficiency, though the slide figures are illustrative rather than measured.
About the speaker:
* Speaker: Daisuke Hozumi
* Company: KYOCERA Europe
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#HighViscosityInkjet, #WaterBasedAutomotivePaint, #ShearThinningFluid, #80mPaSJetting, #PrintedElectronics, #AdditiveManufacturing
12:56 - 14:41
Can a lower-viscosity fluid fail to jet while a higher-viscosity paint succeeds?
Can a lower-viscosity fluid fail to jet while a higher-viscosity paint succeeds?
The printhead achieved approximately 3.27 milliliters per second per printhead. An aqueous xanthan gum solution was chosen because it is shear-thinning like the paint. The three purple results on the left show the xanthan solution had lower complex viscosity than the paint, yet it did not jet while the paint did. A Newtonian reference fluid is shown in green.
On the right, the three results show a longer filament breakup time for the xanthan solution. This suggests delayed droplet separation may have prevented jetting. These are preliminary findings and the mechanism is not yet confirmed. The comparison matters because the lower-complex-viscosity xanthan solution failed while the higher-viscosity paint succeeded, so viscosity alone did not predict jetting in this test.
The work will continue with iPrint to provide useful feedback for printed-electronics material formulation. The conclusion is that high-viscosity jetting could broaden inkjet applications in printed electronics. This is a materials-formulation question as much as a printhead question: the fluid's shear behaviour and filament breakup must be considered alongside complex viscosity.
In this short video, you can learn:
* An aqueous xanthan gum solution had lower complex viscosity than the paint but did not jet, while the paint did.
* The xanthan solution showed a longer filament breakup time, suggesting delayed droplet separation may have prevented jetting, though the mechanism is not confirmed.
* The printhead achieved approximately 3.27 milliliters per second per printhead, and high-viscosity jetting could broaden inkjet applications in printed electronics.
📋 **Clip Abstract** Testing an aqueous xanthan gum solution against paint showed that lower complex viscosity did not guarantee jetting: the xanthan solution failed while the paint succeeded. The three results on the right indicated a longer filament breakup time for xanthan, suggesting delayed droplet separation may have prevented jetting, but these are preliminary findings.
About the speaker:
* Speaker: Daisuke Hozumi
* Company: KYOCERA Europe
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#XanthanGum, #ComplexViscosity, #FilamentBreakup, #HighViscosityJetting, #PrintedElectronics, #InkjetPrinting
10:17 - 12:10
At what viscosity does a 1,584-nozzle printhead stop jetting reliably?
At what viscosity does a 1,584-nozzle printhead stop jetting reliably?
For Newtonian-fluid tests, one pulse per cycle simplified the evaluation, unlike the earlier automotive painting test at 10 pulses per cycle. All 1,584 nozzles were driven at 25 V and 1 kHz for 10,000 commands per nozzle. Liquid collected on glossy paper was weighed, converted to volume, and divided by nozzle count and commands to give average volume per nozzle per command.
Because the average includes nozzles that did not jet, a lower mean can reflect smaller droplets, more failures, or both. Mean volume dropped sharply above about 30 millipascal seconds and trended toward zero around 45 to 50 millipascal seconds. Under these conditions, stable jetting is estimated around 30 millipascal seconds.
The measurement design makes the viscosity limit explicit: 1,584 nozzles, 25 V, 1 kHz, 10,000 commands per nozzle, and weight-to-volume conversion on glossy paper. The sharp decline above 30 millipascal seconds is an aggregate result; it cannot separate droplet-size reduction from nozzle dropout without per-nozzle data.
In this short video, you can learn:
* All 1,584 nozzles were driven at 25 V and 1 kHz for 10,000 commands per nozzle, with average volume calculated from collected liquid weight.
* Mean volume fell sharply above about 30 millipascal seconds and approached zero near 45 to 50 millipascal seconds.
* Stable jetting for this Newtonian fluid under these conditions was estimated around 30 millipascal seconds.
📋 **Clip Abstract** A 1,584-nozzle printhead was evaluated with a Newtonian fluid using one pulse per cycle, 25 V drive, 1 kHz, and 10,000 commands per nozzle. Average volume per nozzle per command dropped sharply above about 30 millipascal seconds and trended toward zero around 45 to 50 millipascal seconds, supporting an estimated stable-jetting limit near 30 millipascal seconds.
About the speaker:
* Speaker: Daisuke Hozumi
* Company: KYOCERA Europe
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#PiezoelectricInkjet, #NewtonianFluidJetting, #NozzleDropVolume, #HighViscosityJetting, #PrintedElectronics, #AdditiveManufacturing
About this talk
→ Exploring Printed Electronics Applications of a Piezoelectric Bend‑Mode Inkjet Printhead for High‑Viscosity Inks · Daisuke Hozumi · The Future of Electronics RESHAPED 2026 Berlin


