Daniel Lacorte | Ames Goldsmith: At $60/oz silver, is plated copper the default — and can these pastes cure in air at 175 °C?
11:07 - 13:10
Other snippets from this talk
Summary of the clip:
At $60/oz silver, is plated copper the default — and can these pastes cure in air at 175 °C?
Curing was addressed directly: the epoxy resin formulation discussed was cured at about 175 °C for one hour in air. Oxidation stability, the speaker noted, depends on the particle size of the material being worked on. The key claim is that these silver-coated copper materials are suitable for curing in air, not only under inert atmosphere — removing the need for a nitrogen or other inert cure environment.
Asked what conductivity came out of that 175 °C, one-hour air cure, the answer was roughly 0.68 or 0.7 milliohm-centimetres of volume resistivity. That figure, as stated in the presentation, is rivaling pure silver in the same formulation — the performance benchmark used to justify swapping part of the silver content for copper.
On the raw-material balancing point, the speaker framed $60/oz silver as a eutectic point: lower and silver-coated copper may not be cost effective, higher and, in his words, everyone and their mother will be looking to formulate with it. Application margin decides — semiconductor die attach carries enough margin for pure silver, while cheaper, lower-margin products can handle silver-coated copper. He noted the same was said when silver was at $30: it is a product of the times.
In this short video, you can learn:
* Silver-coated copper pastes cure at approximately 175 °C for one hour in air rather than requiring an inert atmosphere.
* That air cure delivers about 0.68–0.7 milliohm-centimetres volume resistivity, rivaling pure silver in the same formulation.
* $60/oz silver is presented as the eutectic balancing point, with application margin — die attach versus lower-cost products — determining whether pure silver or silver-coated copper is used.
📋 **Clip Abstract** Curing of silver-coated copper materials was confirmed at roughly 175 °C for one hour in air, with oxidation stability governed by particle size, yielding about 0.68–0.7 milliohm-centimetres volume resistivity and rivaling pure silver in the same formulation. On cost, $60/oz silver was framed as the balancing point where adoption accelerates, with application margin deciding between pure silver for die attach and silver-coated copper for lower-margin products.
About the speaker:
* Speaker: Daniel Lacorte
* Company: Ames Goldsmith
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SilverCoatedCopper, #VolumeResistivity, #AirCurePaste, #DieAttach, #PrintedElectronics, #ConductiveInks
This is a highlight of the presentation:
Advances in Silver-Coated Copper Materials for High-Performance Printed Electronics
More Highlights from the same talk.
02:59 - 04:57
Why does silver-coated copper reach 0.68 mΩ·cm versus pure silver's 0.76 at 80 wt% loading?
Why does silver-coated copper reach 0.68 mΩ·cm versus pure silver's 0.76 at 80 wt% loading?
Silver prices have stabilized around $60 a troy ounce, after reaching $100 to $120 last year and early this year, still roughly triple a couple of years earlier. That volatility drives the need for more sustainable, cost-effective printed-electronics pastes and for reducing total cost of ownership. Silver-coated copper is the manufacturing route discussed: a copper core with a silver surface coating.
The silver coating passivates the copper, adds antioxidative properties and improves reliability versus pure copper, with greater corrosion resistance. The material can be used as is or back-end processed into flakes with various morphologies. In an epoxy formulation loaded at 80 weight percent, the SF134-NM3 pure silver flake and silver-coated copper achieve very similar viscosity at similar weight percent.
Functional data show 0.68 milliohms per centimeter for silver-coated copper versus 0.76 for pure silver. Depending on formulation and constituents, similar functional properties are reached with 85% less silver in the total formulation, giving about 60 to 70% cost reduction. Pure silver is inert, while copper can corrode and affect functional properties, including pot life.
In this short video, you can learn:
* At 80 wt% loading in epoxy, silver-coated copper measured 0.68 mΩ·cm versus 0.76 mΩ·cm for a comparable pure silver flake.
* The formulation can use 85% less silver in total while reaching similar functional properties, translating to about 60–70% cost reduction.
* A silver coating passivates the copper core, adds antioxidative and corrosion-resistant behavior, and improves reliability versus pure copper.
📋 **Clip Abstract** Silver-coated copper uses a copper core with a silver coating to passivate the surface, improve reliability and reduce paste cost as silver prices remain around $60 a troy ounce. At 80 wt% loading in epoxy, it reached 0.68 mΩ·cm versus 0.76 for pure silver, enabling similar functional properties with 85% less silver and about 60–70% cost reduction.
About the speaker:
* Speaker: Daniel Lacorte
* Company: Ames Goldsmith
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SilverCoatedCopper, #ConductivePaste, #CopperCoreFlakes, #MilliohmResistivity, #PrintedElectronics, #AdditiveElectronics
06:45 - 08:59
Spherical, flake or dendritic silver-coated copper — which morphology for fine lines, EMI or conductivity?
Spherical, flake or dendritic silver-coated copper — which morphology for fine lines, EMI or conductivity?
Spherical powders have a narrow particle size distribution for fine-line printing, inks and adhesives. These dense, lower-surface-area powders allow higher solids loading without a large viscosity impact. Multiple particle sizes match screen-printing resolution, and the morphology suits die-attach adhesives needing thermal or electrical conduction.
Flake morphologies have higher aspect ratio and better adhesion onto various substrates in ink or adhesive formulations. They work well in EMI shielding inks where other components in the electronic device need shielding. Particle size, density and solids loading vary by application, requiring a broad materials portfolio.
Dendritic morphologies vary in aspect ratio and particle size. Their oblong morphology creates many particle touchpoints, which can improve electrical conductivity within the ink. Pure copper flakes are also being developed for low-cost thick film applications.
In this short video, you can learn:
* Spherical powders' narrow size distribution and low surface area support fine-line inks and high solids loading.
* Flake morphologies improve adhesion onto substrates and suit EMI shielding inks.
* Dendritic morphologies create many particle touchpoints and can improve electrical conductivity in the ink.
📋 **Clip Abstract** Spherical, flake and dendritic morphologies are selected by particle size, density and solids loading for each application. Spherical powders serve fine-line printing and die attach, flakes serve adhesion and EMI shielding, and dendritic grades target conductivity through many particle touchpoints.
About the speaker:
* Speaker: Daniel Lacorte
* Company: Ames Goldsmith
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SphericalMorphology, #FlakeMorphology, #DendriticMorphology, #EMIShieldingInk, #PrintedElectronics, #ConductiveInks
05:47 - 06:45
Which silver coating leaches the least copper after 48 hours in 2% oleic acid?
Which silver coating leaches the least copper after 48 hours in 2% oleic acid?
A leaching study used one gram of silver-coated copper mixed with about 10 mL of 2% oleic acid in methanol. Copper complex formed and leached into the top solution. The pure-copper control, sample number one, leached the most over time.
After sitting for about 48 hours, sample number three showed the least leaching among five different chemistries. Those five chemistries are widely available in patents and literature, but they were used on the same copper technology. The only difference was the coating chemistry, described as robust.
The comparison isolates coating chemistry rather than the underlying copper. The result points to a silver-coated copper material with reduced leaching in 2% oleic acid/methanol after 48 hours. A broad silver-coated copper portfolio was also presented.
In this short video, you can learn:
* One gram of silver-coated copper was mixed with about 10 mL of 2% oleic acid in methanol for the leaching study.
* After about 48 hours, the pure-copper control leached the most, while sample number three leached the least among five chemistries.
* The five chemistries used the same copper technology, so the only difference was the coating chemistry.
📋 **Clip Abstract** A leaching test mixed one gram of silver-coated copper with about 10 mL of 2% oleic acid in methanol and tracked copper complex formation in the top solution. After about 48 hours, sample number three showed the least leaching among five chemistries that shared the same copper technology, isolating the coating chemistry as the difference.
About the speaker:
* Speaker: Daniel Lacorte
* Company: Ames Goldsmith
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#SilverCoatedCopper, #OleicAcidLeaching, #CopperComplexFormation, #48HourLeaching, #PrintedElectronics, #ConductiveInks
About this talk
→ Advances in Silver-Coated Copper Materials for High-Performance Printed Electronics · Daniel Lacorte · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Daniel Lacorte
- Advancements in metallic particle development for next-generation printed electronics applications · The Future of Electronics RESHAPED 2025 USA
- Advances in metallic particle development and manufacturing: impact on paste and final application · The Future of Electronics RESHAPED 2024 Berlin
More highlights from Daniel Lacorte
- ▶ How can manipulating precipitation process parameters affect the final particle morphology? · The Future of Electronics RESHAPED USA | Boston 2025
- ▶ How does mechanical milling enhance the properties of silver flakes for conductive inks? · The Future of Electronics RESHAPED USA | Boston 2025
- ▶ What are the key conductivity mechanisms in submicron silver flakes, and how do they differ between fired and non-fired applications? · The Future of Electronics RESHAPED USA | Boston 2025
- ▶ Sintering vs. simple contact: Can two completely different conductivity mechanisms achieve the same high performance? · The Future of Electronics RESHAPED 2024
- ▶ How can a simple surface coating on a silver particle be the key to unlocking low-temperature sintering? · The Future of Electronics RESHAPED 2024
- ▶ Can you get better performance for less cost? Why silver-coated copper might be the future for some printed electronics. · The Future of Electronics RESHAPED 2024


