top of page

Doug Hackler

American Semiconductor

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Doug Hackler | American Semiconductor: What limits bulk CMOS silicon to about 10 microns, and how thin can fully depleted SOI go?

23:16 - 24:32

Other snippets from this talk

Summary of the clip:

What limits bulk CMOS silicon to about 10 microns, and how thin can fully depleted SOI go?

The achievable silicon thickness is not set by packaging, but by the chip technology itself. For conventional bulk silicon, such as most SoC processes including the one used by Nordic, thickness is limited to no less than about 10 microns. That limit sits roughly a manufacturing tolerance away from the critical threshold or critical junction depth in that CMOS process.

For thinner technologies, fully depleted SOI demonstrates a much lower floor. Chips have been done with silicon thicknesses as small as 0.2 microns. In that case only the active portion of the silicon is kept as part of the package. This shows the thickness floor is tied to the process architecture, not a single packaging constraint.

The discussion frames the demonstration as feasible for commercialization in an industrial setting. The hope stated is that this demonstrated capacity can be further expanded to other parts of the industry. The thickness answer separates bulk CMOS limits from fully depleted SOI capability, and packaging does not determine the minimum silicon thickness.

In this short video, you can learn:
* Bulk CMOS silicon thickness is limited to no less than about 10 microns, roughly a manufacturing tolerance from the critical junction depth.
* Fully depleted SOI chips have been made with silicon thicknesses as small as 0.2 microns.
* In the 0.2-micron case, only the active portion of the silicon remains part of the package.

đŸ“‹ **Clip Abstract** Silicon thickness is determined by chip technology rather than packaging. Bulk CMOS is limited to about 10 microns by critical junction depth, while fully depleted SOI has reached 0.2 microns with only the active silicon retained.

About the speaker:
* Speaker: Doug Hackler
* Company: American Semiconductor
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#BulkCMOSThickness, #FullyDepletedSOI, #CriticalJunctionDepth, #ActiveSiliconLayer, #FlexibleHybridElectronics, #SemiconductorPackaging

This is a highlight of the presentation:

State-of-the-Art and Issues for Bluetooth® Flexible Hybrid Electronics (FHE)

Printed, Hybrid, Structural & 3D Electronics 2021

​

11-12 May 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

04:45 - 06:10

Why is a polymer-encapsulated chip that is half polyimide and half silicon the lowest-cost protected fan-in package?

Why is a polymer-encapsulated chip that is half polyimide and half silicon the lowest-cost protected fan-in package?

Semiconductor-on-polymer is a chip-scale packaging technology for integrated circuits that makes the thinnest chips possible. The comparison is drawn left to right: a conventional SoC package, a bare semiconductor die in the middle, which in some cases has been tried for this style of electronics, and, at the far right, the semiconductor-on-polymer packaged IC. SOP sits in that third position.

On that far-right chip, half of the thickness of the very, very thin device is the poly packaging material that gives it reliability. It is a package encapsulated in polyimide. Only half the thickness of that device is semiconductor material, so the polymer is not a coating added afterwards but the structural half of the chip-scale package itself.

The SOP chip-scale package process is specifically wafer-level chip-scale processing, WLCSP. Its advantages: it is very, very thin, very, very flexible, and it is the lowest-cost protected fan-in process on the market today. Protected fan-in means the ability to protect all six sides of the chip, four of them very, very thin, with a polymer coating that provides better reliability.

In this short video, you can learn:
* Half the thickness of an SOP device is polyimide packaging material, with only the other half being semiconductor.
* SOP is built with wafer-level chip-scale processing (WLCSP), which delivers very thin and very flexible die.
* It is described as the lowest-cost protected fan-in process on the market today, protecting all six sides of the chip.

đŸ“‹ **Clip Abstract** Semiconductor-on-polymer chip-scale packaging thins an IC until half its thickness is polyimide encapsulant and half is silicon. Built with wafer-level chip-scale processing, it protects all six sides of the die and is positioned as the lowest-cost protected fan-in process available.

About the speaker:
* Speaker: Doug Hackler
* Company: American Semiconductor
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#SemiconductorOnPolymer, #WaferLevelChipScaleProcessing, #ProtectedFanIn, #PolyimideEncapsulation, #ChipScalePackaging, #FlexibleHybridElectronics

12:07 - 13:30

Why does direct flip-chip assembly of ultra-thin Bluetooth stall at a 50-micron pad pitch, and on which substrates?

Why does direct flip-chip assembly of ultra-thin Bluetooth stall at a 50-micron pad pitch, and on which substrates?

Direct interconnect means flip-chip mounting the ultra-thin chip straight onto the flexible circuit board. It is elegant and works well when the board's pad pitch — the space between the connections being made to the chip — exceeds roughly 25 microns. Commercial production today is generally limited to a 25-micron pad with a 25-micron space, a 50-micron pitch, and that is about as good as high-volume capability gets.

That high-volume capability exists on copper-on-polyimide, a fairly expensive substrate. The same feature size is not yet proven on PET, and the conductivity of traces there is not proven to support Bluetooth functionality; it certainly has not made its way to paper or other substrates. So the finest available routing sits on the costliest base material.

The interposer shown earlier is offered as a bridge — a way to move some of this forward while board-level pitch and substrate limits persist. Direct flip-chip onto flex is elegant where pitch allows, but the combination of a 50-micron production floor and copper-on-polyimide economics keeps the ultra-thin Bluetooth path constrained at the board interface.

In this short video, you can learn:
* Direct flip-chip interconnect works well only above roughly a 25-micron pad and space, so 50 microns is the practical pitch floor in high-volume production.
* That 50-micron capability is available on copper-on-polyimide, an expensive substrate, and is unproven on PET and on paper.
* Trace conductivity on PET has not been shown to support Bluetooth, which is why an interposer is proposed as a bridge.

đŸ“‹ **Clip Abstract** Direct flip-chip mounting of ultra-thin chips works well only when flexible board pad pitch exceeds about 25 microns, and high-volume production stalls at a 50-micron pitch. That capability lives on costly copper-on-polyimide, is unproven on PET for feature size and Bluetooth trace conductivity, and has not reached paper, leaving an interposer as a possible bridge.

About the speaker:
* Speaker: Doug Hackler
* Company: American Semiconductor
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#DirectInterconnect, #CopperOnPolyimide, #PadPitch, #FlipChipBonding, #FlexibleHybridElectronics, #PrintedElectronics


About this talk

→ State-of-the-Art and Issues for Bluetooth® Flexible Hybrid Electronics (FHE) · Doug Hackler · Printed, Hybrid, Structural, & 3D Electronics 2021

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page