top of page

Florian Mathies

Helmholtz-Zentrum Berlin

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Florian Mathies | Helmholtz-Zentrum Berlin: Can a transmission scan along the vial's Z-axis separate a stable perovskite ink from one that splits in three hours?

09:45 - 11:31

Other snippets from this talk

Summary of the clip:

Can a transmission scan along the vial's Z-axis separate a stable perovskite ink from one that splits in three hours?

The measurement tool comes from a Berlin-based company that specialises in dispersions; industry routinely uses it to track how inks age and how stable they are. The group first applied it to particle-containing transport layers — nickel oxide, C60, ETL or HTL materials — then asked whether the same or a similar system works for perovskites.

A fresh perovskite ink shows the usual yellow shape in the vial. After three hours of standing, two phases separate. Transmission is recorded along a line of the Z-axis across the whole area, and the spectra move from yellow, the first, to blue, the last, as particles fall down — a direct representation of what the naked eye sees.

So a bad ink with particles inside is simply not stable, while a stabilised perovskite ink shows mainly no difference in the transmission scan. Some inks hold for more than two weeks. The results are new: the project was run in September only.

In this short video, you can learn:
* Transmission measured along the Z-axis across the vial converts particle settling into a quantitative aging trace that mirrors what the eye observes.
* An unstabilised perovskite ink separates into two phases within three hours and shifts from a yellow to a blue spectrum as particles fall.
* The same dispersion-aging system already used industrially for nickel oxide and C60 applies to perovskite inks, with stabilised formulations lasting beyond two weeks.

📋 **Clip Abstract** A Berlin-made dispersion-aging instrument records transmission along the Z-axis of a vial to track how perovskite inks sediment over time. Unstabilised inks split into two phases within three hours, moving from a yellow to a blue spectrum, while stabilised inks show almost no change and hold for more than two weeks.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#PerovskiteInkStability, #ZAxisTransmission, #ParticleSedimentation, #NickelOxideDispersion, #PerovskiteSolarCells, #SolutionProcessing

This is a highlight of the presentation:

Turning Perovskite Innovation into Impact: The Solar TAP Approach

​

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

04:53 - 06:57

How does the Stage-Gate framework help scale perovskite solar cells from lab spin-coating to automated slot-die deposition?

How does the Stage-Gate framework help scale perovskite solar cells from lab spin-coating to automated slot-die deposition?

The Stage-Gate publication investigated single-junction perovskite solar cells and identified stages from small-area lab devices to mini modules, where PicoQuant showed early results, then larger modules maybe two square meters. The established framework covers perovskite and organic photovoltaics, the project's two main photovoltaic technologies.

This open-innovation action sits at low TRL, maybe three or four, even two, because spin coating is solely a lab process. Three involved centres aligned processes and working groups, establishing a common perovskite architecture and baseline as a standing operating procedure, so efficiencies can transfer between centres.

In future runs, slot-die coating is used, not only manual slot-die coating by a lab engineer or PhD student, but automated fabrication platforms, for example from Cypress, which also partners in SolarTEP. This future run uses slot die coating with automated fabrication platforms.

In this short video, you can learn:
* The Stage-Gate framework maps single-junction perovskite solar cells from small-area lab devices through PicoQuant mini modules to modules maybe two square meters.
* Three centres aligned processes and working groups to establish a common perovskite architecture and baseline as a standing operating procedure, enabling transferable efficiencies.
* Future runs use slot-die coating, moving from manual coating by a lab engineer or PhD student to automated fabrication platforms from Cypress, a SolarTEP partner.

📋 **Clip Abstract** A Stage-Gate framework for single-junction perovskite solar cells defines stages from small-area lab devices to mini modules, where PicoQuant showed early results, and larger modules maybe two square meters. The low-TRL open-innovation action aligned three centres on a common perovskite baseline, with future slot-die coating moving from manual operation to automated fabrication platforms such as Cypress.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#PerovskiteSolarCells, #SlotDieCoating, #AutomatedFabricationPlatforms, #TransferableEfficiencies, #OrganicPhotovoltaics, #EmergingPhotovoltaics

05:14 - 07:24

What stage-gate criteria separate a lab perovskite device from a pilot-line-ready material?

What stage-gate criteria separate a lab perovskite device from a pilot-line-ready material?

The stage-gate process maps the steps from a small lab area to a big pilot line: what measurements are needed and how quality is measured. Driven by the Jülich group in the Solartab network, it gives a basis to develop further processes and projects within Solartab.

As the schematic shows, moving from a lab-based process where devices are worked on to different stages means scaling up: faster scale-up and larger modules. At the end, the materials actually used and usable in the process become fewer and fewer, while materials at the device level remain more research-focused.

Within the stage-gate process, materials reaching the later stages can be considered usable for a pilot line, whereas materials at the beginning, on a device level, are more research-focused. There may be many challenges to overcome to bring them to a higher stage level.

In this short video, you can learn:
* The stage-gate process defines what measurements and quality checks are needed between a small lab area and a big pilot line.
* The Jülich group drove this stage-gate process within the Solartab network to develop further processes and projects.
* Later-stage materials are fewer and more likely usable for a pilot line, while device-level materials remain research-focused with challenges to scale.

📋 **Clip Abstract** A stage-gate process connects small lab-area work to a big pilot line by defining steps, measurements and quality checks. Driven by the Jülich group in the Solartab network, it shows that scaling up yields faster, larger modules with fewer usable materials, while device-level materials remain research-focused and face challenges at higher stages.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin

Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect

Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect

#StageGateProcess, #PilotLineScaleUp, #SolartabNetwork, #MaterialQualityChecks, #PerovskiteSolarCells, #OpenInnovationActions

10:06 - 11:29

Why does Europe still debate lead while China runs gigawatt perovskite single-junction and tandem factories?

Why does Europe still debate lead while China runs gigawatt perovskite single-junction and tandem factories?

The assessment is stark: China already has gigawatt factories producing perovskite solar cells, both single junctions and tandems. Europe remains in a debate over whether lead is acceptable, so the region is way behind on industrial adoption. Collaborators from China still show willingness to work with European groups, but that does not remove the competitive gap.

European research centres still bring expertise, especially on the analytics side, according to discussions with Chinese collaborators. That analytical capability is a lever for collaboration, not a claim of manufacturing parity. However, finding collaboration partners within Europe or Germany for new projects is becoming harder, which complicates the route from lab results to industrial relevance.

An audience question then asks whether machine learning and material prediction are relied on before fabricating devices. The question is posed but not answered here. The surrounding message remains the same: industrial scale in China, analytical strength in Europe, and a shrinking pool of European or German project partners.

In this short video, you can learn:
* China already operates gigawatt factories for perovskite solar cells, including single junctions and tandems, while Europe still debates lead.
* European groups are seen as bringing strong analytics expertise, and Chinese collaborators remain willing to work with them.
* Finding collaboration partners within Europe or Germany for new projects is getting harder, and the audience question on machine learning and material prediction was not answered in this excerpt.

📋 **Clip Abstract** China has gigawatt factories producing perovskite solar cells, both single junctions and tandems, while Europe remains behind and still debates whether lead is acceptable. European research groups retain analytics expertise and Chinese collaborators still work with them, but finding European or German project partners is becoming harder, and a question on machine learning and material prediction before device fabrication goes unanswered here.

About the speaker:
* Speaker: Florian Mathies
* Company: Helmholtz-Zentrum Berlin
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#PerovskiteSolarCells, #SingleJunctionTandems, #GigawattFactories, #AnalyticsExpertise, #Photovoltaics, #SolarIndustry


About this talk

→ Turning Perovskite Innovation into Impact: The Solar TAP Approach · Florian Mathies · Perovskite Connect 2026


More highlights from Florian Mathies

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page