top of page

Franz Vollman

Heraeus

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Franz Vollman | Heraeus: Why is the separation of material supply and equipment manufacturing the biggest bottleneck in printed electronics scaling?

00:04:48 - 00:06:09

Other snippets from this talk

Summary of the clip:

Why is the separation of material supply and equipment manufacturing the biggest bottleneck in printed electronics scaling?

Vollman highlights that true mass production readiness in printed electronics cannot be achieved by offering materials or equipment in isolation. By integrating ink manufacturing, specialized inkjet printing hardware, and process parameters into a single turnkey system, developers can avoid the classic finger-pointing between chemistry suppliers and machine OEMs.

Specifically, Heraeus utilizes Metal Organic Decomposition (MOD) inks (particle-free silver precursors) whose fluid dynamics, viscosity, and evaporation profiles are directly co-engineered with the printing system's thermal and physical properties. This holistic optimization is critical because even minor chemical modifications drastically alter jetting performance and deposition accuracy.

Ultimately, this system-level ownership bridges the gap between lab-scale feasibility and 24/7 industrial fab reliability. Mass-production clients receive a single, accountable interface rather than a fragmented supply chain, allowing rapid deployment of selective metallic coatings without compromising process yield.

In this short video, you can learn:
* Why combining ink formulation, printing hardware, and process parameters under one roof accelerates mass-production readiness.
* The role of Metal Organic Decomposition (MOD) particle-free inks in achieving consistent fluid dynamics.
* How co-engineering materials and hardware eliminates the classic disconnect between chemistry and mechanical tooling in semiconductor fabs.
📋 **Clip Abstract** This clip highlights the strategic and technical benefits of integrating materials, equipment, and process engineering into a single turnkey solution for printed electronics. By co-developing particle-free MOD inks alongside industrial inkjet systems, Heraeus overcomes the typical yield and integration challenges of the semiconductor supply chain.

#MetalOrganicDecomposition, #ParticleFreeInks, #IndustrialInkjet, #AdditiveMetallization, #PrintedElectronics, #SemiconductorPackaging

This is a highlight of the presentation:

​

The Future of Electronics RESHAPED 2023 Berlin

Electronics RESHAPED Europe

​

Estrel Congress Centre, Berlin, Germany, Europe

Organised By:

TechBlick

​

More Highlights from the same talk.

00:34 - 02:01

What does a printed shield buy you over sputtering: 25% lower cost, 3x speed, or mmWave performance?

What does a printed shield buy you over sputtering: 25% lower cost, 3x speed, or mmWave performance?

The offering is framed as a system solution rather than a single material: it combines a shielding material, the printing equipment, the curing equipment and the process behind them. The functional claim is high shielding performance spanning the sub-GHz range up to the mmWave range between 20 and 40 GHz, achieved with a very thin coating. Data on that performance was promised later in the presentation.

Because the coating is digital, partial coating and selective shielding are changed simply by altering the print picture, so the shielded area can be changed right away. The pattern lives in the data rather than in a fixed format, so shielding is applied only where it is wanted on the package. That is the functional argument for printing over fixed-coverage deposition.

The commercial case is up to 25% lower total cost of ownership compared with an existing solution such as sputter, while savings against traditional cages or a gasket solution would be by far higher. Process speed is up to a factor of three faster than sputter. Equipment brings less CapEx and a smaller footprint on the equipment portion, with more detail promised later.

In this short video, you can learn:
* The system pairs a shielding material with printing and curing equipment plus the process behind it, rather than selling a material alone.
* Shielding performance is claimed from the sub-GHz range through the 20 to 40 GHz mmWave band, using a very thin coating.
* Total cost of ownership is up to 25% lower than sputter and process speed up to 3x higher, with lower CapEx and a smaller equipment footprint.

📋 **Clip Abstract** A conformal EMI shielding system for semiconductor packages combines material, printing and curing equipment with the process, claiming shielding from sub-GHz up to the 20 to 40 GHz mmWave range in a very thin coating. Digital patterning enables selective, partial coating changed by editing the print picture, while the commercial case cites up to 25% lower total cost of ownership versus sputter, up to 3x process speed, lower CapEx and a smaller footprint.

About the speaker:
* Speaker: Franz Vollman
* Company: Heraeus
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#ConformalEMIShielding, #DigitalSelectiveCoating, #SputterComparison, #MmWaveShielding, #SemiconductorPackaging, #PrintedElectronics

10:37 - 12:01

Can a 2.5 µm inkjet silver layer rival 8 µm sputtered shielding from 800 MHz to 9 GHz?

Can a 2.5 µm inkjet silver layer rival 8 µm sputtered shielding from 800 MHz to 9 GHz?

The comparison sets a 2.5 µm inkjet-printed silver layer against an approximately 8 µm sputtered part. From 800 MHz to 9 GHz, the printed layer delivers superior shielding effectiveness with very small fluctuations in the 1–9 GHz band. At very low frequencies, skin effect limits the thinner printed layer, so it is not as good as sputter, yet it still reaches -60 to -17 dB.

Between 30 MHz and 1 GHz, the result is already described as very stable. In 1 GHz to 9 GHz, the inkjet silver shows an excellent result, again with very small fluctuations. The sputtered reference is thicker at about 8 µm, but the printed part is only about 2.5 µm, so the shielding comparison is not simply thickness-for-thickness.

For 12 GHz to 50 GHz, measurements used a horn antenna rather than the broadband loop antenna, so they are not directly comparable. Even there, a pretty stable further shielding result appears in the higher frequency range. That stability, together with the 800 MHz to 9 GHz data, supports using one kind of technology across the tested shielding bands.

In this short video, you can learn:
* A 2.5 µm inkjet silver layer is compared with an approximately 8 µm sputtered part.
* Shielding is superior from 800 MHz to 9 GHz, with very small fluctuations between 1 GHz and 9 GHz.
* At low frequencies skin effect reduces performance to -60 to -17 dB, while 12–50 GHz horn-antenna data show stable shielding but are not directly comparable.

📋 **Clip Abstract** A 2.5 µm inkjet-printed silver layer is benchmarked against an approximately 8 µm sputtered part for shielding effectiveness. The printed layer shows superior shielding from 800 MHz to 9 GHz, stable low-frequency behavior from -60 to -17 dB, and stable 12–50 GHz results measured with a horn antenna, though those high-frequency data are not directly comparable.

About the speaker:
* Speaker: Franz Vollman
* Company: Heraeus
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#InkjetSilverShielding, #SputteredReference, #SkinEffect, #HornAntenna, #EMIShielding, #ConformalElectronics

04:34 - 06:23

Why does a particle-free MOD ink avoid the nozzle clogging and reproducibility limits of nanoparticle silver inks?

Why does a particle-free MOD ink avoid the nozzle clogging and reproducibility limits of nanoparticle silver inks?

The first component is a particle-free ink. An MOD, or metal organic decomposition ink, is not a nanoparticle ink: the metal precursor is mixed in a solvent with a complexing agent, then filled directly into the inkjet printing equipment and printed onto the substrate, for example epoxy mold compound. Because there are no particles in the ink, there is no agglomeration potential, no risk of nozzle clogging, and a very high reproducibility of the process.

Application is an industrial-scale inkjet printing process, and the solvents evaporate very easily, which gives a very good result in terms of sintering. That delivers very high stability in the ink system coupled with very high conductivity. On the curing side, UV curing is currently built into the equipment, with infrared curing or flash curing also possible.

In its dried and cured stage the ink reaches about 50% of bulk silver conductivity, with a very low sheet resistance at roughly 2 to 2.5 micron layer thickness, plus an excellent shielding performance. Latest adhesion data from various tests is also reported alongside those results, addressing a second reliability question for shielding on epoxy mold compound.

In this short video, you can learn:
* MOD inks are particle-free because the metal precursor is dissolved with a complexing agent rather than dispersed as particles, removing agglomeration and nozzle-clogging risk.
* Deposition runs on industrial-scale inkjet equipment, and UV curing is built in today, with infrared and flash curing cited as alternatives.
* Cured layers reach roughly 50% of bulk silver conductivity with low sheet resistance at 2 to 2.5 micron thickness, plus excellent shielding.

📋 **Clip Abstract** The first system component is a particle-free MOD ink in which a metal precursor and complexing agent are dissolved in solvent, so nothing agglomerates and nothing clogs the printhead. Industrial inkjet deposition onto epoxy mold compound, UV or infrared or flash curing, and roughly 50% of bulk silver conductivity at 2 to 2.5 micron thickness complete the picture, with shielding and adhesion data to match.

About the speaker:
* Speaker: Franz Vollman
* Company: Heraeus
* Event: Printed, Flexible, Hybrid & InMold Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, hybrid electronics, sustainable electronics
https://www.techblick.com/

#MODInk, #EpoxyMoldCompound, #FlashCuring, #SilverConductivity, #ConformalEMIShielding, #PrintedElectronics

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page