top of page

Giovanni Obando

Voltera

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Giovanni Obando | Voltera: Why is precise dispenser-body temperature control critical for keeping conductive ink viscosity stable during R&D?

16:00 - 18:05

Other snippets from this talk

Summary of the clip:

Why is precise dispenser-body temperature control critical for keeping conductive ink viscosity stable during R&D?

In high-precision printed electronics, even minor fluctuations in ambient lab temperature can drastically alter the viscosity of functional inks. Voltera addresses this rheological challenge by integrating active heating directly into the dispenser body rather than relying on a heated nozzle tip. By maintaining the cartridge body at a constant 30 to 35 degrees Celsius, the system effectively decouples ink rheology from ambient room variations.

While heated nozzles can assist in specialized low-melting-point applications, stabilizing the entire fluid reservoir ensures consistent shear rates and extrusion volumes throughout extended print runs. This thermal stability is crucial when prototype designers work with highly sensitive, customized third-party formulations that exhibit temperature-dependent shear-thinning behaviors.

This robust material handling has driven adoption among major athletic OEMs like Nike and Under Armour for prototyping flexible pressure sensors and smart garments. By bridging the gap between raw ink formulation and repeatable dispensing, the system provides a reliable platform for transitioning textile electronics from academic concepts to commercial prototypes.

In this short video, you can learn:
* How active dispenser-body heating at 30 to 35°C mitigates ambient lab temperature fluctuations to stabilize ink viscosity.
* The technical trade-offs between localized nozzle tip heating and bulk reservoir thermal stabilization.
* Real-world R&D applications of the technology by tier-one athletic apparel brands developing printed biometric sensors.
📋 **Clip Abstract** Learn how the NOVA platform controls ink rheology by stabilizing the dispenser body temperature between 30 and 35°C during high-precision printing. It also discusses commercial applications where major athletic brands utilize this technology to prototype advanced wearable sensors.
🔗 Link in comments 👇

#InkRheology, #ActiveThermalStabilization, #ConductiveInks, #ViscosityControl, #PrintedElectronics, #SmartTextiles

This is a highlight of the presentation:

Wearable Electronics: Printing Silver Conductive Ink on Cotton Fabric

Future of Electronics RESHAPED USA 2026

10-11 June 2026

Computer History Museum, Mountain View, California, USA

Organised By:

TechBlick

​

More Highlights from the same talk.

08:53 - 10:01

What are the viscosity limits, cost trade-offs, and scaling limitations of Direct Ink Writing for printed electronics prototyping?

What are the viscosity limits, cost trade-offs, and scaling limitations of Direct Ink Writing for printed electronics prototyping?

Direct ink writing is a digital massless, nozzle-based extrusion method for viscous and paste-like materials. It suits functional materials and fine features, but is typically slower and less precise. For rapid prototyping, it is one of the most ideal methods. Its viscosity range is very wide, more than a thousand centipoise. A direct-write R&D printer recommends 1000 to a million centipoise. Cost of setup is low to moderate: simple dispensing setups, but slower throughput.

The process handles a broad range of materials from conductive pastes to dielectrics to adhesives, epoxies, and prototyping. That material flexibility is why prototyping is labeled excellent. The digital process handles many materials and remains flexible for functional inks. However, it should be noted that it is too slow for scaling. Setup cost is low to moderate, with simple dispensing setups, but throughput is slower.

Direct ink writing's viscosity range is very wide, about more than a thousand centipoise, and the direct-write R&D printer recommends 1000 to a million centipoise. It is a nozzle-based extrusion for viscous and paste-like materials, suited to functional materials and fine features. The method is typically slower and less precise, but for rapid prototyping it is one of the most ideal methods. Its broad material range includes conductive pastes, dielectrics, adhesives and epoxies.

In this short video, you can learn:
* Direct ink writing uses nozzle-based extrusion for viscous and paste-like materials, with a recommended viscosity window of 1000 to a million centipoise.
* It handles conductive pastes, dielectrics, adhesives and epoxies, with low-to-moderate setup cost but slower throughput.
* The method is excellent for rapid prototyping and functional materials, yet it is too slow for scaling.

📋 **Clip Abstract** Direct ink writing is a digital massless, nozzle-based extrusion process for viscous and paste-like materials, with a viscosity range from 1000 to a million centipoise. It offers low-to-moderate setup cost and excellent rapid prototyping across conductive pastes, dielectrics, adhesives and epoxies, but remains too slow for scaling.

About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#DirectInkWriting, #ConductivePastes, #DirectWritePrinter, #RapidPrototyping, #PrintedElectronics, #AdditiveElectronics

17:16 - 18:47

What are the critical rheological and particle size rules required to prevent clogging in direct ink writing?

What are the critical rheological and particle size rules required to prevent clogging in direct ink writing?

Shear thinning behaviour: the ink flows when pressure is applied and quickly recovers viscosity after dispensing. This is the type of shear response wanted from these materials. A high storage modulus allows ink to hold its shape after dispensing, which is very important for direct ink writing. These two rheological requirements govern how a deposited line behaves once it leaves the nozzle.

Particle size dictates nozzle diameter. The largest particles in a particle size distribution should not exceed one seventh of the diameter of the nozzle to enable smooth flow. If particle size is 10 microns, multiplying by seven to ten points to a 70 to 100 micron nozzle diameter to avoid any clogging. The ratio, not a fixed micron figure, is what protects the nozzle.

Post-processing and substrate selection complete the picture. Inks differ in curing profile: there are UV curable inks, thermally cured inks, and some that air dry. Post-processing directly affects mechanical and electrical properties, which is why data sheets state time and temperature for maximum performance. Substrates vary with formulation, and ink properties such as solvents used in processing requirements must be considered when choosing a material.

In this short video, you can learn:
* Shear thinning inks flow under pressure and quickly recover viscosity after dispensing, which is the shear response required.
* A high storage modulus lets dispensed ink hold its shape, a critical property for direct ink writing.
* The largest particle in a distribution must stay below one seventh of the nozzle diameter; a 10 micron particle implies a 70 to 100 micron nozzle.

📋 **Clip Abstract** Shear thinning, rapid viscosity recovery and a high storage modulus define the rheology that direct ink writing needs for shape retention. The largest particles must not exceed one seventh of the nozzle diameter—10 micron particles demand a 70 to 100 micron nozzle—while curing profile, post-processing time and temperature, and substrate selection determine final mechanical and electrical properties.

About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#DirectInkWrite, #ShearThinningInks, #ParticleSizeDistribution, #InkCuringProfiles, #PrintedElectronics, #AdditiveElectronics

14:10 - 15:51

How does positive mechanical displacement compare to pneumatic and auger systems in high-viscosity direct ink writing?

How does positive mechanical displacement compare to pneumatic and auger systems in high-viscosity direct ink writing?

A motor or driven piston provides mechanical displacement. In this machine, a plunger pushes onto the white piston inside the cartridge, pressurising the material and sending it through a pressure sensor before extrusion from a single nozzle diameter. Flow rate is controlled by the motion of that displacement element. The benefits are high accuracy and repeatability each stroke, because a rotation dispenses a predictable volume.

It handles a wide range of viscosities, including paste adhesives and other high-viscosity materials, unaffected by back pressure or reservoir level. Continuous or dot dispensing depends on programming. The drawbacks are slower maximum speed than jetting or pneumatic dispensing, poor suitability for ultra-low viscosities in the inkjet range, more complex hardware, and higher cost from motor seals and moving parts. The x, y, z gantry system also feeds into printer cost.

Comparing the options: pneumatic dispensing is cheapest but inconsistent and clog prone, while auger valve dispensing is precise but sensitive to particle size. Mechanical displacement controls flow rate through the motion of the displacement element, so each rotation dispenses a predictable volume. It is unaffected by back pressure or reservoir level, handles paste adhesives and other high-viscosity materials, and can do continuous or dot dispensing depending on programming, but hardware complexity and moving parts raise cost and lower maximum speed.

In this short video, you can learn:
* Positive displacement dispensing controls flow rate by the motion of a motor or driven piston, giving high accuracy and repeatability with a predictable volume per rotation.
* It suits high-viscosity paste adhesives and is unaffected by back pressure or reservoir level, but is slower than jetting or pneumatic dispensing and not ideal for ultra-low viscosities in the inkjet range.
* Pneumatic dispensing is cheapest but inconsistent and clog prone, while auger valve dispensing is precise but sensitive to particle size.

📋 **Clip Abstract** This segment contrasts positive mechanical displacement with pneumatic and auger dispensing for direct ink writing. It details cartridge pressurisation, pressure sensing, single-nozzle extrusion, viscosity range, speed limits, hardware complexity and cost drivers in an x, y, z gantry system.

About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#DirectInkWrite, #PositiveDisplacement, #PasteAdhesives, #PredictableVolumeDispensing, #PrintedElectronics, #AdditiveManufacturing

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page