Giovanni Obando | Voltera: Can you direct-write high-viscosity MXene and gallium inks without clogging nozzle geometry?
04:02 - 06:13
Other snippets from this talk
Summary of the clip:
Can you direct-write high-viscosity MXene and gallium inks without clogging nozzle geometry?
Direct-write printed electronics R&D demands precise extrusion control over highly viscous functional inks. The NOVA platform utilizes mechanical positive displacement to force thick-film pastes through a single micro-nozzle. This positive displacement architecture bypasses the limitations of traditional pneumatic dispensing, allowing researchers to process highly non-Newtonian fluids.
The system's rheological sweet spot ranges from 1,000 to 1,000,000 centipoise, accommodating challenging third-party formulations like silver, copper, gold, gallium, and MXene inks. To enable complex multi-layer sensor stack-ups, the platform integrates a 70-micron resolution onboard camera. This allows for real-time augmented reality alignment, ensuring perfect layer registration when depositing conductive and insulating layers sequentially.
By utilizing a vacuum table to secure thin-film substrates like PET and Kapton, the system minimizes mechanical distortion during printing. This mechanical stability, combined with positive displacement extrusion, provides researchers with a highly repeatable tool for rapid prototyping of advanced sensors and flexible circuits.
In this short video, you can learn:
* How mechanical positive displacement overcomes pneumatic extrusion limitations for non-Newtonian inks.
* The rheological operating window of 1,000 to 1,000,000 centipoise for novel materials like gallium and MXene.
* Utilizing a 70-micron resolution camera with AR overlay for precise multi-layer sensor registration.
📋 **Clip Abstract** Discover how the NOVA platform utilizes direct-write positive displacement to dispense extremely high-viscosity materials up to 1,000,000 cPs. Learn how real-time AR camera alignment enables highly accurate multi-layer stack-ups for advanced sensor R&D.
🔗 Link in comments 👇
#PositiveDisplacementExtrusion, #DirectWritePrinting, #MXeneInks, #HighViscosityPrinting, #PrintedElectronics, #FlexibleSensors
This is a highlight of the presentation:
Wearable Electronics: Printing Silver Conductive Ink on Cotton Fabric
Future of Electronics RESHAPED USA 2026
10-11 June 2026
Computer History Museum, Mountain View, California, USA
Organised By:
TechBlick
More Highlights from the same talk.
08:53 - 10:01
What are the viscosity limits, cost trade-offs, and scaling limitations of Direct Ink Writing for printed electronics prototyping?
What are the viscosity limits, cost trade-offs, and scaling limitations of Direct Ink Writing for printed electronics prototyping?
Direct ink writing is a digital massless, nozzle-based extrusion method for viscous and paste-like materials. It suits functional materials and fine features, but is typically slower and less precise. For rapid prototyping, it is one of the most ideal methods. Its viscosity range is very wide, more than a thousand centipoise. A direct-write R&D printer recommends 1000 to a million centipoise. Cost of setup is low to moderate: simple dispensing setups, but slower throughput.
The process handles a broad range of materials from conductive pastes to dielectrics to adhesives, epoxies, and prototyping. That material flexibility is why prototyping is labeled excellent. The digital process handles many materials and remains flexible for functional inks. However, it should be noted that it is too slow for scaling. Setup cost is low to moderate, with simple dispensing setups, but throughput is slower.
Direct ink writing's viscosity range is very wide, about more than a thousand centipoise, and the direct-write R&D printer recommends 1000 to a million centipoise. It is a nozzle-based extrusion for viscous and paste-like materials, suited to functional materials and fine features. The method is typically slower and less precise, but for rapid prototyping it is one of the most ideal methods. Its broad material range includes conductive pastes, dielectrics, adhesives and epoxies.
In this short video, you can learn:
* Direct ink writing uses nozzle-based extrusion for viscous and paste-like materials, with a recommended viscosity window of 1000 to a million centipoise.
* It handles conductive pastes, dielectrics, adhesives and epoxies, with low-to-moderate setup cost but slower throughput.
* The method is excellent for rapid prototyping and functional materials, yet it is too slow for scaling.
📋 **Clip Abstract** Direct ink writing is a digital massless, nozzle-based extrusion process for viscous and paste-like materials, with a viscosity range from 1000 to a million centipoise. It offers low-to-moderate setup cost and excellent rapid prototyping across conductive pastes, dielectrics, adhesives and epoxies, but remains too slow for scaling.
About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#DirectInkWriting, #ConductivePastes, #DirectWritePrinter, #RapidPrototyping, #PrintedElectronics, #AdditiveElectronics
17:16 - 18:47
What are the critical rheological and particle size rules required to prevent clogging in direct ink writing?
What are the critical rheological and particle size rules required to prevent clogging in direct ink writing?
Shear thinning behaviour: the ink flows when pressure is applied and quickly recovers viscosity after dispensing. This is the type of shear response wanted from these materials. A high storage modulus allows ink to hold its shape after dispensing, which is very important for direct ink writing. These two rheological requirements govern how a deposited line behaves once it leaves the nozzle.
Particle size dictates nozzle diameter. The largest particles in a particle size distribution should not exceed one seventh of the diameter of the nozzle to enable smooth flow. If particle size is 10 microns, multiplying by seven to ten points to a 70 to 100 micron nozzle diameter to avoid any clogging. The ratio, not a fixed micron figure, is what protects the nozzle.
Post-processing and substrate selection complete the picture. Inks differ in curing profile: there are UV curable inks, thermally cured inks, and some that air dry. Post-processing directly affects mechanical and electrical properties, which is why data sheets state time and temperature for maximum performance. Substrates vary with formulation, and ink properties such as solvents used in processing requirements must be considered when choosing a material.
In this short video, you can learn:
* Shear thinning inks flow under pressure and quickly recover viscosity after dispensing, which is the shear response required.
* A high storage modulus lets dispensed ink hold its shape, a critical property for direct ink writing.
* The largest particle in a distribution must stay below one seventh of the nozzle diameter; a 10 micron particle implies a 70 to 100 micron nozzle.
📋 **Clip Abstract** Shear thinning, rapid viscosity recovery and a high storage modulus define the rheology that direct ink writing needs for shape retention. The largest particles must not exceed one seventh of the nozzle diameter—10 micron particles demand a 70 to 100 micron nozzle—while curing profile, post-processing time and temperature, and substrate selection determine final mechanical and electrical properties.
About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#DirectInkWrite, #ShearThinningInks, #ParticleSizeDistribution, #InkCuringProfiles, #PrintedElectronics, #AdditiveElectronics
14:10 - 15:51
How does positive mechanical displacement compare to pneumatic and auger systems in high-viscosity direct ink writing?
How does positive mechanical displacement compare to pneumatic and auger systems in high-viscosity direct ink writing?
A motor or driven piston provides mechanical displacement. In this machine, a plunger pushes onto the white piston inside the cartridge, pressurising the material and sending it through a pressure sensor before extrusion from a single nozzle diameter. Flow rate is controlled by the motion of that displacement element. The benefits are high accuracy and repeatability each stroke, because a rotation dispenses a predictable volume.
It handles a wide range of viscosities, including paste adhesives and other high-viscosity materials, unaffected by back pressure or reservoir level. Continuous or dot dispensing depends on programming. The drawbacks are slower maximum speed than jetting or pneumatic dispensing, poor suitability for ultra-low viscosities in the inkjet range, more complex hardware, and higher cost from motor seals and moving parts. The x, y, z gantry system also feeds into printer cost.
Comparing the options: pneumatic dispensing is cheapest but inconsistent and clog prone, while auger valve dispensing is precise but sensitive to particle size. Mechanical displacement controls flow rate through the motion of the displacement element, so each rotation dispenses a predictable volume. It is unaffected by back pressure or reservoir level, handles paste adhesives and other high-viscosity materials, and can do continuous or dot dispensing depending on programming, but hardware complexity and moving parts raise cost and lower maximum speed.
In this short video, you can learn:
* Positive displacement dispensing controls flow rate by the motion of a motor or driven piston, giving high accuracy and repeatability with a predictable volume per rotation.
* It suits high-viscosity paste adhesives and is unaffected by back pressure or reservoir level, but is slower than jetting or pneumatic dispensing and not ideal for ultra-low viscosities in the inkjet range.
* Pneumatic dispensing is cheapest but inconsistent and clog prone, while auger valve dispensing is precise but sensitive to particle size.
📋 **Clip Abstract** This segment contrasts positive mechanical displacement with pneumatic and auger dispensing for direct ink writing. It details cartridge pressurisation, pressure sensing, single-nozzle extrusion, viscosity range, speed limits, hardware complexity and cost drivers in an x, y, z gantry system.
About the speaker:
* Speaker: Giovanni Obando
* Company: Voltera
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#DirectInkWrite, #PositiveDisplacement, #PasteAdhesives, #PredictableVolumeDispensing, #PrintedElectronics, #AdditiveManufacturing
About this talk
→ Wearable Electronics: Printing Silver Conductive Ink on Cotton Fabric · Giovanni Obando · Electronics RESHAPED USA 2026
More highlights from Giovanni Obando
- ▶ What are the viscosity limits, cost trade-offs, and scaling limitations of Direct Ink Writing for printed electronics prototyping? · The Future of Electronics RESHAPED 2025 | Berlin
- ▶ How does positive mechanical displacement compare to pneumatic and auger systems in high-viscosity direct ink writing? · The Future of Electronics RESHAPED 2025 | Berlin
- ▶ What are the critical rheological and particle size rules required to prevent clogging in direct ink writing? · The Future of Electronics RESHAPED 2025 | Berlin
- ▶ What are the material trade-offs, curing challenges, and cost differences between copper and gold conductive inks? · The Future of Electronics RESHAPED 2025 | Berlin
- ▶ How can silver and gold inks be layered to keep a stretchable electrode biocompatible and electrically functional? · The Future of Electronics RESHAPED 2025 | Berlin


