top of page

Joseph Stephens

NanoSen GmbH

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Joseph Stephens | NanoSen GmbH: Can a 0.4 mm nanoparticle-filled silicone survive 20 million 200 N cycles without force-sensor drift?

00:53 - 02:55

Other snippets from this talk

Summary of the clip:

Can a 0.4 mm nanoparticle-filled silicone survive 20 million 200 N cycles without force-sensor drift?

Thin force sensors usually mean conductive-ink force sensing resistors or capacitive sensors. Force sensing resistors are cheap, everywhere and easy to make, but they are fragile, overload resistance is very small, constant force breaks them over time, calibration is lost, measurements become inconsistent and temperature drift appears. The proposed alternative is a polymer nanocomposite force-sensing material.

The material is a 0.4 millimeter thin medical-grade silicone made electrically conductive with nanoparticles, forming the polymer nanocomposite. A sample can be passed around, crushed, stepped on and driven over with a car; the material does not care. A 20 millimeter round sensor can measure from one gram up to 20 kilos.

Durability data include 20 million cycles at 200 newtons with no material degradation. The sensor range is large, and temperature stability covers minus 20 to 70 degrees. The curve offset is about 3% over the entire curve, not percentage per degree, which supports long-term use. These metrics are presented as the basis for a new generation of force sensors.

In this short video, you can learn:
* Conductive-ink force sensing resistors are cheap but fragile, lose calibration under constant force, give inconsistent measurements and show temperature drift.
* The alternative is a 0.4 millimeter medical-grade silicone made conductive with nanoparticles; a 20 millimeter round sensor measures one gram to 20 kilos.
* The material survived 20 million cycles at 200 newtons without degradation and showed about 3% curve offset from minus 20 to 70 degrees.

📋 **Clip Abstract** Conductive-ink force sensing resistors are cheap but fragile, lose calibration under constant force, drift with temperature and give inconsistent measurements. A polymer nanocomposite of 0.4 millimeter medical-grade silicone made conductive with nanoparticles is presented as the alternative, with a 20 millimeter sensor measuring one gram to 20 kilos and surviving 20 million cycles at 200 newtons without degradation.

About the speaker:
* Speaker: Joseph Stephens
* Company: NanoSen GmbH
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#ForceSensingResistor, #PolymerNanocomposite, #MedicalGradeSilicone, #CycleDurability, #FlexibleSensors, #ElectronicTextiles

This is a highlight of the presentation:

Force Sensing Impedance Materials for Flexible Applications

Electronic Textiles RESHAPED 2026 | Berlin

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

​

​

More Highlights from the same talk.

03:52 - 05:06

How can a €2 force sensor use one Renesas chip for six channels at 1.6 kHz?

How can a €2 force sensor use one Renesas chip for six channels at 1.6 kHz?

Manufacturing cost target for a low-cost single sensor is about two euros. A single impedance chip from Renesas measures up to six sensors, and that one chip already communicates over SPI, so the configuration is very comparable to force sensing resistors, yet a single chip gives a working concept for talking to the onboard MCU.

The same chip delivers 1.6 kilohertz of samples per second, which makes it attractive for several applications. The electrodes do not have to be Kapton or gold-plated copper either: screen printed ink and screen printed copper have been shown working on Kapton, PET, paper and TPU. That is another place where the material supports low-cost applications.

Sensor performance does differ across those substrates, but the performance curve is about the same, so the material gives flexibility rather than substrate lock-in. It can be cut out in any shape or form, and the electrodes plus impedance measurement together represent a large opportunity. The result is a printed sensor stack that keeps its behaviour curve while substrate and outline change.

In this short video, you can learn:
* One Renesas impedance chip addresses up to six sensors over SPI at 1.6 kHz, aimed at roughly €2 manufacturing cost.
* Screen printed ink and screen printed copper electrodes work on Kapton, PET, paper and TPU, not only gold-plated copper on Kapton.
* Performance differs between those substrates but the curve shape stays about the same, and the material can be cut into any shape or form.

📋 **Clip Abstract** Low-cost force sensing can be built around a single Renesas impedance chip reading up to six channels over SPI at 1.6 kHz, with manufacturing cost around two euros. Screen printed ink and copper electrodes on Kapton, PET, paper and TPU keep a comparable performance curve, so the sensor can be cut into any shape.

About the speaker:
* Speaker: Joseph Stephens
* Company: NanoSen GmbH
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#ImpedanceSensing, #ScreenPrintedCopper, #SixChannelReadout, #KilohertzSampling, #FlexibleElectronics, #PrintedElectronics

05:35 - 07:33

How does AC impedance in a 0.4 mm silicone sensor measure 85 microns and enable a 22-ton washer load cell?

How does AC impedance in a 0.4 mm silicone sensor measure 85 microns and enable a 22-ton washer load cell?

Direct-current resistance and capacitance are compared with other sensors, but this material is driven with an AC signal and measured by impedance. Compression brings more particles together: resistance drops, capacitance increases, and the impedance curve for a 20 mm sensor is non-linear from 1 gram to 20 kilos. The curvature comes from silicone requiring exponentially more force as it presses back, yet the response is repeatable and calibratable.

The material is 0.4 millimeters thin and can accurately, repeatably measure 85 microns of compression. In the demonstration, the red numbers show 15 microns of compression, with each LED representing 0.001 millimeters. That resolution supports replacing load cells in selected applications: instead of gluing strain gauges into a deforming housing, the material sits in the housing, compresses by a couple of microns up to 85, and forms the load cell.

A washer on the table measures up to 22 tons of force because its metal housing compresses by a total of 15 microns. That lets the soft material address industrial monitoring and other load-cell replacements, not just thin-film force sensing. The same compression mechanism yields new properties compared with other thin-film force sensors, giving flexibility for industrial applications.

In this short video, you can learn:
* AC impedance exploits particle contact: compression lowers resistance and raises capacitance, producing a repeatable, calibratable curve for a 20 mm sensor from 1 gram to 20 kilos.
* At 0.4 mm thin, the material repeatably resolves 85 microns of compression, with the demo showing 15 microns and each LED equal to 0.001 mm.
* A washer load cell measures up to 22 tons because the metal housing compresses by 15 microns, enabling industrial monitoring.

📋 **Clip Abstract** The material uses AC impedance rather than DC resistance or capacitance, so particle contact under compression produces a non-linear but repeatable and calibratable response from 1 gram to 20 kilos on a 20 mm sensor. At 0.4 mm thin it resolves 85 microns, demonstrated at 15 microns, and a washer housing compressing 15 microns measures up to 22 tons for industrial monitoring.

About the speaker:
* Speaker: Joseph Stephens
* Company: NanoSen GmbH
* Event: Electronic Textiles RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Electronic Textiles RESHAPED 2027 | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronictextilesreshaped

#ACImpedance, #ParticleSilicone, #85MicronCompression, #22TonWasherLoadCell, #FlexibleForceSensing, #IndustrialMonitoring


About this talk

→ Force Sensing Impedance Materials for Flexible Applications · Joseph Stephens · The Future of Electronics RESHAPED 2026 Berlin


Other talks by Joseph Stephens

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page