top of page

Jurgen van Peer, Frank Louwet

Nanogate, Agfa

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Jurgen van Peer, Frank Louwet | Nanogate, Agfa: What are the key technical and economic trade-offs between screen printing and digital inkjet for printed electronics manufacturing?

04:43 - 06:41

Other snippets from this talk

Summary of the clip:

What are the key technical and economic trade-offs between screen printing and digital inkjet for printed electronics manufacturing?

The comparison starts from a table adapted from an industrial inkjet printing handbook. Rather than treating the numbers as fixed, the focus is on essential process differences because field developments can make figures debatable. Screen printing needs hard tooling, which can be expensive for high-resolution work, while inkjet tooling mainly concerns software-based preprocessing of the design.

Cost per run differs by run length: screen printing is expected to be lower for longer runs because of higher speed and/or process maturity, while inkjet has a clear advantage for short runs. Contact also separates them. Screen printing has non-negligible media contact, whereas inkjet is definitely non-contact. Screen printing also brings material losses when excess material is removed from the screen and may become unusable.

Ink exposure is another difference: screen inks are exposed to the environment, leading to unwanted changes in printing behavior. Ink availability also diverges. Screen ink portfolios are wide and allow larger particles unless very fine patterns are needed. Inkjet inks can only contain small particles, so nanosilver or other nanoscale materials are better suited.

In this short video, you can learn:
* Screen printing requires hard tooling that can be expensive for high-resolution work, whereas inkjet tooling is mainly software-based design preprocessing.
* Screen printing is expected to have lower cost per run for longer runs due to higher speed and/or maturity, while inkjet is advantageous for short runs.
* Inkjet is non-contact and limited to small particles such as nanosilver, while screen printing is contact-based, can lose excess material, exposes inks to the environment and supports wider ink portfolios with larger particles unless fine patterns are required.

📋 **Clip Abstract** Digital inkjet and screen printing differ in tooling, run economics, contact, material loss and ink constraints. Screen printing uses hard tooling and wide inks but has contact and exposure issues, while inkjet is non-contact, software-preprocessed and suited to short runs and nanoscale inks.

About the speakers:
* Speakers: Jurgen van Peer, Frank Louwet
* Companies: Nanogate, Agfa
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#ScreenPrintingTooling, #DigitalInkjetPreprocessing, #NanosilverInks, #NonContactInkjet, #PrintedElectronics, #IndustrialInkjetPrinting

This is a highlight of the presentation:

Printed Electronics made with Digital Printing: Materials and Applications in Motor Sport

Printed, Hybrid, Structural & 3D Electronics 2021

​

11-12 May 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

03:03 - 04:48

How do fluid dynamics and dot placement requirements differ between graphical printing and functional printed electronics?

How do fluid dynamics and dot placement requirements differ between graphical printing and functional printed electronics?

Graphics printing aims at fooling the human eye, so the number of dots and their exact positioning may not be so relevant. Resolution still matters, and so does avoiding banding or differing gloss levels, to which the eye is very sensitive. The dot pattern is judged by how the eye integrates it, not by the precision of each landing position.

Functional printing carries graphics requirements too: a geometric shape must be filled with dots of a certain size, which is called pattern fidelity. Sharp edges must be built from liquid dots with a certain overlap without creating defects such as bulging, which can induce unwanted short circuits between separated design features. Dot size after the droplet reaches the substrate, and dot-to-dot distance, determine this.

Another aspect of functional printing is that different functions are realised with inks that can widely differ in composition but still must work together in one system. Compositional freedom per function is therefore constrained by the need for the whole ink set to be compatible. This leads to the question of why digital printing is used for printed electronics and how it compares with screen printing.

In this short video, you can learn:
* In graphics the eye is the final judge, so banding and gloss uniformity outweigh exact dot positioning.
* Pattern fidelity means filling a geometric shape with dots of a set size, a graphics requirement functional printing inherits.
* Bulging where liquid dots overlap can short separated design features, so dot size on the substrate and dot-to-dot distance set the process window.

📋 **Clip Abstract** Inkjet places dots, but graphics uses them to fool the human eye while functional printing builds features that must not short. The talk unpacks pattern fidelity, edge definition against bulging, and multi-ink compatibility before turning to digital versus screen printing.

About the speakers:
* Speakers: Jurgen van Peer, Frank Louwet
* Companies: Nanogate, Agfa
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#InkjetDotPlacement, #PatternFidelity, #EdgeBulging, #InkSetCompatibility, #PrintedElectronics, #DigitalPrinting

21:26 - 23:09

How does an inkjet-printed silver grid heater outperform carbon nanotube films in speed and power efficiency for motor sport visors?

How does an inkjet-printed silver grid heater outperform carbon nanotube films in speed and power efficiency for motor sport visors?

Nanogate collaborated with Agfa to develop a transparent heater for motorsport helmet visors using Prelect SPS 211 ink. By depositing an inkjet-printed grid onto polycarbonate, the team evaluated its performance against carbon nanotube film technology in an apple-to-apple comparison at an operating voltage of 24 volts.

The inkjet-printed heater exhibited lower electrical resistance compared to the carbon nanotube benchmark, delivering higher power output. Driven at 24 volts, the printed structure reached 35 degrees Celsius within 10 seconds. The thermal response yields totally homogeneous heating and fast color bleaching, ensuring a superior driver experience without quickly draining helmet-integrated solar batteries.

Digital manufacturing allows instant customization to fit specific visor shapes and dimensions directly through printer software adjustments. This digital workflow enables flexible production runs ranging from single custom prototypes to small series of 5 or 10 units. Combined with Agfa silver and graphical inks on polycarbonate, inkjet printing provides a versatile approach for functional motorsport applications.

In this short video, you can learn:
* Prelect SPS 211 ink enables inkjet-printed transparent grid heaters on polycarbonate with lower resistance than carbon nanotube films.
* At 24 volts, the inkjet-printed transparent heater reaches 35 degrees Celsius in 10 seconds to provide fast, homogeneous bleaching.
* Digital printer software allows instant customization of visor heating patterns for production runs of single units or small series.

📋 **Clip Abstract** Printed transparent heaters using Agfa silver and graphical inks on polycarbonate achieve lower resistance and higher power output than carbon nanotube films at 24 volts. Achieving homogeneous heating to 35 degrees Celsius within 10 seconds, the digital inkjet process allows rapid customization of visor geometries with minimal battery drain.

About the speakers:
* Speakers: Jurgen van Peer, Frank Louwet
* Companies: Nanogate, Agfa
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#AgfaPrelect, #InkjetPrinting, #TransparentHeater, #HomogeneousHeating, #PrintedElectronics, #StructuralElectronics

11:41 - 13:42

How does Prelect SPS 211 speed sintering while limiting thermoformed-line resistance rise?

How does Prelect SPS 211 speed sintering while limiting thermoformed-line resistance rise?

Prelect SPS 211 sits in the same family as SPS 201, with comparable silver loading but an improved sintering profile. Continuous resistance measurements on printed lines at 110°C, 130°C and 150°C show the two inks reaching about the same final line resistance. The new ink reaches that value faster at all three temperatures, and the difference is most pronounced at the lowest temperature.

In the plotted data, thin lines correspond to SPS 201 and thick lines to SPS 211, making the time-to-resistance comparison direct. At 110°C, 130°C and 150°C the final line resistance is about the same, so the gain is faster sintering rather than a lower endpoint. The effect is more outspoken at lower temperature.

Formability was tested by printing a line pattern on polycarbonate film with a primer layer and thermoforming it with two different stamps or designs of increasing deformation. For the lines deformed most, resistance increased by 6 to 15%. This opens the door for applications on mildly deformed surfaces.

In this short video, you can learn:
* Prelect SPS 211 has comparable silver loading to SPS 201 but reaches about the same final line resistance faster at 110°C, 130°C and 150°C.
* The sintering-time advantage is more outspoken at the lower oven temperature.
* Thermoforming printed lines on primer-coated polycarbonate increased resistance by 6 to 15% for the most deformed lines.

📋 **Clip Abstract** Prelect SPS 211 is a new ink in the same family as SPS 201, with comparable silver loading and an improved sintering profile. Continuous resistance measurements at 110°C, 130°C and 150°C show comparable final line resistance but faster sintering for SPS 211, while thermoforming on primer-coated polycarbonate raises resistance by 6 to 15% for the most deformed lines.

About the speakers:
* Speakers: Jurgen van Peer, Frank Louwet
* Companies: Nanogate, Agfa
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#PrelectSPS211, #SilverLoading, #SinteringProfile, #ThermoformingFormability, #PrintedElectronics, #FlexibleElectronics

Links to this speaker's talk page and other highlights appear here.

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page