Luigi Vesce | University of Rome Tor Vergata: How does perovskite deposition follow La Mer nucleation, and why deposit 2-propanol as anti-solvent?
06:20 - 07:46
Other snippets from this talk
Summary of the clip:
How does perovskite deposition follow La Mer nucleation, and why deposit 2-propanol as anti-solvent?
The deposition process is optimised around the La Mer model: a supersaturation state, burst nucleation, then perovskite crystal growth. For a triple-cation perovskite, the precursor is deposited first with air assistance to help preliminary drying. The same approach was later confirmed as good for different kinds of perovskite.
In the one-step process, an anti-solvent is then deposited. Here, 2-propanol is used to start the burst nucleation step. The final thermal step completes perovskite crystal growth. Each layer except the counter electrode and one ETL is deposited with their machine.
This process sequence places La Mer nucleation control inside the deposition machine: precursor deposition and preliminary air drying, then 2-propanol anti-solvent addition, then thermal growth. The triple-cation perovskite was the initial optimised case, and the same approach was confirmed as good for different kinds of perovskite over the years.
In this short video, you can learn:
* La Mer nucleation is mapped to supersaturation, burst nucleation and crystal growth in the perovskite deposition process.
* 2-propanol is deposited as anti-solvent to trigger burst nucleation, then the final thermal step completes crystal growth.
* The triple-cation perovskite process was optimised first and later confirmed as good for different kinds of perovskite.
📋 **Clip Abstract** The deposition of perovskite layers is optimised according to the La Mer model, with a supersaturation state, burst nucleation and crystal growth. Air-assisted precursor deposition and 2-propanol anti-solvent addition are followed by a final thermal step, and the approach was confirmed for different perovskites.
About the speaker:
* Speaker: Luigi Vesce
* Company: University of Rome Tor Vergata
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#LaMerNucleation, #2PropanolAntiSolvent, #TripleCationPerovskite, #ThermalCrystalGrowth, #PerovskiteSolarCells, #PrintedElectronics
This is a highlight of the presentation:
Beyond the Lab: Scaling Perovskite Solar Cells into Printed Modules
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
02:42 - 04:45
Why divide a module into narrow series cells instead of scaling one large perovskite cell?
Why divide a module into narrow series cells instead of scaling one large perovskite cell?
A module is not one enlarged cell; it is an interconnection of different cells. The reason is substrate losses: a very large single cell of centimetres would suffer losses on the substrate. The module route therefore accepts division into cells connected in series, because the full large area must be segmented rather than scaled as one device.
To reduce those losses, the substrate must have low sheet resistance, around 7 to 10 ohms per square. The large area is divided into series-connected cells, and the width of those cells must be optimised to minimise loss. Interconnection area and interconnection resistance are further scale-up issues, optimisable through the laser process.
Layer inhomogeneity is another scale-up issue, linked to the printing techniques, the materials used, and the working environment. The typical IPP architecture uses P1, P2 and P3. P1 is made on the substrate to divide the cells; P2 follows deposition of all layers; P3 interrupts the counter electrode to provide one single electrode over the device.
In this short video, you can learn:
* A module interconnects multiple cells because a very large single cell would incur substrate losses.
* Low sheet resistance of about 7–10 ohms per square and optimised cell width are required to reduce losses in series-connected modules.
* P1 divides cells on the substrate, P2 follows deposition of all layers, and P3 interrupts the counter electrode.
📋 **Clip Abstract** The clip explains why perovskite scale-up uses modules made of interconnected series cells rather than one large cell: substrate losses force segmentation. It identifies low sheet resistance, optimised cell width, laser-optimised interconnection resistance and printing-related layer inhomogeneity as key scale-up issues, then introduces the P1/P2/P3 IPP architecture.
About the speaker:
* Speaker: Luigi Vesce
* Company: University of Rome Tor Vergata
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#SeriesCellInterconnection, #LowSheetResistance, #LaserInterconnection, #P1P2P3Architecture, #PerovskiteSolarCells, #PrintedElectronics
19:02 - 21:03
Does the step-by-step formulation optimization deliver a 16.1% module stable beyond 3,000 hours?
Does the step-by-step formulation optimization deliver a 16.1% module stable beyond 3,000 hours?
The optimization is presented step by step, showing how each formulation step can improve performance before everything is used together. Electroluminescence imaging of the module shows small defects and local series-resistance variation, but no huge thickness variation and no shunts. There is also no contribution outside the aperture area, so the measurement captures the exact module part.
Deposition pictures and images from different module regions further support uniformity. With all steps combined, the module reaches 16.1%. The result includes shorter MPPT tracking and long stability of more than 3,000 hours according to the ISO D1 test. Compared with the lab-scale cell, the drop is about 9% to 10%, with no losses versus the mini module.
The comparison indicates that performance obtained on a one-centimeter-square mini module can be upscaled to a very large module without losses. That is presented as a strong result, but the target remains higher performance. The clip therefore links uniform deposition, electroluminescence imaging and stability testing to the 16.1% module result and its 3,000-hour ISO D1 tracking.
In this short video, you can learn:
* Electroluminescence imaging reveals small defects and local series-resistance variation without huge thickness variation or shunts.
* Combining the formulation steps yields 16.1% and more than 3,000 hours of stability under the ISO D1 test.
* The module shows about 9% to 10% drop versus the lab-scale cell and no losses versus the one-centimeter-square mini module.
📋 **Clip Abstract** A step-by-step formulation optimization is evaluated using electroluminescence imaging, deposition images and aperture-area measurement. Combining the steps produces a 16.1% module with more than 3,000 hours of ISO D1 stability, about 9% to 10% below the lab cell and with no losses versus the one-centimeter-square mini module.
About the speaker:
* Speaker: Luigi Vesce
* Company: University of Rome Tor Vergata
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ElectroluminescenceImaging, #ApertureAreaMeasurement, #MPPTTracking, #ISOD1Stability, #PerovskiteSolarCells, #PrintedPhotovoltaics
14:12 - 16:13
Why did blade coating the anti-solvent fail on large substrates, and how did slot-die restore DMSO removal?
Why did blade coating the anti-solvent fail on large substrates, and how did slot-die restore DMSO removal?
On the large-area substrate, the process stayed in ambient air but required modification: a passivation layer was added on the perovskite. The original route used the blade coater for both the perovskite and the anti-solvent. That combination produced a very poor perovskite layer, reflected in very low current, because the anti-solvent could not properly wash the DMSO from the formulation.
The failure was geometric: the meniscus at some point of the substrate could not follow the full length because the substrate is too big. So the second step was moved to a slot-die coater. This enabled effective DMSO removal across the full substrate and gave the reported 12.6% performance. They are now planning slot-die for both the first and second steps.
Even at 12.6%, the performance is not enough. The losses are caused by layer inhomogeneity. In the described flow, the blade anti-solvent limitation led to incomplete DMSO washing and poor current, while slot-die for the second step provided effective DMSO removal on the full substrate. Inhomogeneity remains the stated loss mechanism.
In this short video, you can learn:
* Blade coating both perovskite and anti-solvent on the large substrate produced a poor layer and very low current.
* The anti-solvent meniscus could not follow the full substrate length, so DMSO was not washed effectively.
* Moving the second step to slot-die removed DMSO across the full substrate and reached 12.6%, while layer inhomogeneity caused remaining losses.
📋 **Clip Abstract** Blade coating both the perovskite and anti-solvent failed on a large substrate because the meniscus could not follow the full length, leaving DMSO poorly washed and current very low. Adding a slot-die coater for the second step enabled effective DMSO removal across the full substrate and 12.6% performance, though layer inhomogeneity still caused losses.
About the speaker:
* Speaker: Luigi Vesce
* Company: University of Rome Tor Vergata
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#SlotDieCoating, #DMSOWashing, #BladeCoating, #LargeAreaPerovskite, #PerovskiteSolarCells, #PrintedElectronics
Other talks by Luigi Vesce
- Scalable and Ambient-Air Processing of Printed Perovskite PV Modules · The Future of Electronics RESHAPED 2025
More highlights from Luigi Vesce
- ▶ Can perovskite solar cells ever escape the lab without solving the P1-P2-P3 laser scribing dead area problem? · Perovskite Connect 2025
- ▶ Is the reliance on gold electrodes quietly ruining the environmental and economic viability of perovskite solar modules? · Perovskite Connect 2025
- ▶ How do you bypass the nightmare of laser scribing carbon back-contacts in fully printed perovskite solar modules? · Perovskite Connect 2025


