Margaret H. Samuels | NASA Goddard Space Flight Center: How do 15-minute sounding rockets and 5-hour balloons deliver fast, low-budget flight qualification?
10:11 - 11:45
Other snippets from this talk
Summary of the clip:
How do 15-minute sounding rockets and 5-hour balloons deliver fast, low-budget flight qualification?
Sounding rockets and scientific balloons are the two suborbital programs described, both operated out of Wallops Flight Facility on the Virginia coast at Chincoteague. With multiple strategic launch sites and more than ten launches a year, the programs are fast and low budget, and they explicitly enable technologies that need flight exposure.
Dedicated missions on each program exist purely to fly lots of new technologies and try them out, alongside heliophysics and Earth science work; sounding rockets originally targeted solar-flare measurement. Flights last about 15 minutes: launch, touch space, and splash down in water, giving a rapid read on how hardware behaves in that environment.
Scientific balloons stretch the exposure window: the shortest flights are five hours, and those are the ones this hardware has already flown on. Some campaigns reach Antarctica. Together the two platforms bracket the qualification space, minutes versus hours, before a technology commits to a longer, costlier mission.
In this short video, you can learn:
* Wallops Flight Facility runs both the sounding rocket and scientific balloon programs, with ten-plus launches a year across multiple strategic launch sites.
* Sounding rocket flights last roughly 15 minutes, touching space and splashing down in water, enough to gauge how a technology operates in that environment.
* The shortest scientific balloon flights are five hours, and some campaigns go as far as Antarctica.
π **Clip Abstract** Suborbital platforms offer a fast, low-budget route to flight qualification: sounding rockets give roughly 15 minutes at the edge of space, while scientific balloons hold payloads aloft for five hours or more. Both programs, operated from Wallops Flight Facility, reserve dedicated missions for flying lots of new technologies alongside heliophysics and Earth science.
About the speaker:
* Speaker: Margaret H. Samuels
* Company: NASA Goddard Space Flight Center
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#SoundingRockets, #ScientificBalloons, #WallopsFlightFacility, #SolarFlareScience, #SuborbitalResearch, #SpaceflightElectronics
This is a highlight of the presentation:
3D Printed Grounding Strap for Low SWaP Electrical Failure Mitigation during Spaceflight Missions
More Highlights from the same talk.
01:25 - 03:42
Can a printed grounding strap on the A3 battery wall meet Ultem adhesion, 1.5 A heat dissipation, outgassing and lunar thermal cycling?
Can a printed grounding strap on the A3 battery wall meet Ultem adhesion, 1.5 A heat dissipation, outgassing and lunar thermal cycling?
The Lunar Environment Monitoring Station, LeMS, is a handheld instrument for astronauts at the south lunar pole to measure moonquakes. Its portable A3 battery already had a specific weight requirement and was over it. Adding another grounding strap would add more mass, so the lead asked whether one could be printed and be less massive.
The proposal was to print the grounding strap on the inside of the battery wall. NASA started from project and scientist requirements. The printed strap had to adhere to Ultem, the plastic wall material, and dissipate heat for one and a half amps. The 1.5 A number prompted caution.
Because the mission had never flown to a lunar environment, outgassing testing was required. Goddardβs materials group performs all official NASA outgassing testing, and its databases are publicly available. The batteryβs electronics also defined a thermal-cycling temperature range; the south lunar pole system would see a much larger range.
In this short video, you can learn:
* LeMS is a handheld south-lunar-pole instrument for measuring moonquakes, and its portable A3 battery needed a lighter grounding solution.
* The printed strap was proposed for the inside of the battery wall and had to bond to Ultem while dissipating 1.5 A.
* NASA outgassing testing and a defined thermal-cycling range were mandatory because the mission had not flown to a lunar environment.
π **Clip Abstract** A LeMS battery that was already over its weight requirement needed another grounding strap, so the team proposed printing one on the inside Ultem wall to reduce mass. The design had to dissipate 1.5 A, pass NASA outgassing testing and survive the battery electronicsβ thermal-cycling range for south lunar pole use.
About the speaker:
* Speaker: Margaret H. Samuels
* Company: NASA Goddard Space Flight Center
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#PrintedGroundingStrap, #UltemBatteryWall, #OutgassingTesting, #LunarThermalCycling, #PrintedElectronics, #SpaceflightMaterials
07:39 - 09:25
Did the printed silver strap survive 1.5 A and cut grounding-strap mass by 94%?
Did the printed silver strap survive 1.5 A and cut grounding-strap mass by 94%?
Resistance came from a four-point probe measurement, with cross-sectional area calculated from profilometry. Each structure was driven with a hot 1.5 A current for the entire measurement while voltage drop was logged, yielding resistance and resistivity. Bone structures of different lengths and mid-section thicknesses all carried 1.5 A without smoking, arcing or showing failure β described as unusual.
Other inks were screened, but only this one performed well; the ones that did not do so well were left out of the summary. The key winner is carrying 1.5 A. Printing the grounding strap instead of using a commercial flight-heritage part gave a 94% mass reduction, 10 g down to 0.6 g, plus reduced volume.
Printing the strap on the inside of the wall makes room for other hardware inside the battery and the module as a whole. Adhesion, outgassing and thermal shock testing were used to retire those risks, and the team reports having met targets for all of these tests.
In this short video, you can learn:
* Four-point probe measurement with profilometry-derived cross-section delivered resistivity from a continuous 1.5 A hot-current test.
* Every printed bone structure, across differing lengths and thicknesses, took 1.5 A with no smoking, no arcing and no failure.
* The printed strap replaced a commercial flight-heritage part at 94% lower mass, 10 g to 0.6 g, while meeting adhesion, outgassing and thermal shock targets.
π **Clip Abstract** A printed grounding strap was electrically characterised by four-point probe resistivity under a continuous 1.5 A hot current, and every geometry tested survived without smoking, arcing or failure. Substituting it for a commercial flight-heritage strap cut mass by 94%, from 10 g to 0.6 g, with adhesion, outgassing and thermal shock testing meeting targets.
About the speaker:
* Speaker: Margaret H. Samuels
* Company: NASA Goddard Space Flight Center
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#PrintedGroundingStrap, #FourPointProbeResistivity, #ThermalShockTesting, #NinetyFourPercentMassReduction, #AdditiveElectronics, #SpaceflightHardware
04:47 - 06:49
What adhesion, outgassing and thermal-shock results did a printed silver grounding strap achieve?
What adhesion, outgassing and thermal-shock results did a printed silver grounding strap achieve?
Adhesion testing used ACI FSO 142 silver ink on the flat areas, performed by Kai, an intern. The printed silver ink is described as highly conductive and achieved a 4B ratingβthe second-highest rating besides perfect. That 4B result represents less than 5% removal of material, shown in the before-and-after images.
For outgassing, the team printed on pre-weighed foils, exposed them inside a vacuum system to evaporate, then measured mass before and after. The key metric was total mass loss. Although the acceptable bar depends on the mission, less than 1% is usually good for spaceflight; 0.3% was a very nice result.
Thermal shock served as accelerated thermal cycling in stacked hot and cold boxes, with the device wired in the hot box and dropped through a central hole for rapid temperature changes. Testing ran about 10 cycles over eight hours from -55 C to 65 C. There were no significant crack propagations; more importantly, electrical continuity before and after was emphasized.
In this short video, you can learn:
* ACI FSO 142 silver ink achieved a 4B adhesion rating, the second-highest rating, with less than 5% material removal.
* Outgassing total mass loss reached 0.3%, below the usual less-than-1% bar for spaceflight missions.
* About 10 thermal-shock cycles from -55 C to 65 C over eight hours showed no significant crack propagation, with electrical continuity before and after emphasized.
π **Clip Abstract** A printed silver grounding strap was evaluated with ACI FSO 142 ink for spaceflight electrical failure mitigation. Adhesion reached 4B with under 5% removal, outgassing total mass loss was 0.3%, and roughly 10 thermal-shock cycles from -55 C to 65 C over eight hours showed no significant crack propagation.
About the speaker:
* Speaker: Margaret H. Samuels
* Company: NASA Goddard Space Flight Center
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#SilverInkAdhesion, #OutgassingMassLoss, #ThermalShockCycling, #PrintedGroundingStrap, #PrintedElectronics, #SpaceflightElectronics
About this talk
β 3D Printed Grounding Strap for Low SWaP Electrical Failure Mitigation during Spaceflight Missions Β· Margaret H. Samuels Β· The Future of Electronics RESHAPED 2026 Berlin


