Mario Kohl | Fraunhofer IFAM: Do printed Type K and Type T thermocouples hold tolerance class one against wire references, and where do they drift?
16:53 - 19:05
Other snippets from this talk
Summary of the clip:
Do printed Type K and Type T thermocouples hold tolerance class one against wire references, and where do they drift?
Printed Type K thermocouples were benchmarked against a standard wire thermocouple. Up to 250 °C the printed devices sat inside the DIN EN 60584 tolerance class one band, with a spread of 1.5 kelvin. Pushing the same structures to 450 °C widened the deviation range, but the results still stayed inside tolerance class two. So the printed junction tracks its wire reference closely at moderate temperature and degrades gracefully rather than failing.
The main focus shifts to Type T — copper against copper-nickel-manganese. Here the influence of the base powder material was tested directly. One route used pre-alloyed copper-manganese; the other took elemental copper, nickel and manganese, mixed them in the right amounts to build the alloy in-house, then sintered at a set temperature so the alloy formed during sintering. Comparing those powder routes is the point of the experiment.
Against the reference wire thermocouple, plotted in blue, the printed Type T devices showed really good accordance. The drops visible in the trace are the furnace regulation during the test, not sensor error. The in-house formed alloys matched best; the elemental powder versions were also okay, landing around half a kelvin to 0.75 kelvin deviation. Both powder routes therefore reproduce the reference, with the pre-alloyed route carrying the tighter agreement.
In this short video, you can learn:
* Printed Type K thermocouples stayed within tolerance class one up to 250 °C, with a 1.5 kelvin spread against a standard wire reference.
* At 450 °C the Type K deviation range widened, yet the results still referred to tolerance class two.
* Type T printed from pre-alloyed copper-manganese and from elemental copper, nickel and manganese mixed in-house both followed the reference wire thermocouple.
📋 **Clip Abstract** Printed Type K and Type T thermocouples were benchmarked against standard wire references across 250 °C and 450 °C test runs, with tolerance class one held at the lower temperature. Type T devices built from pre-alloyed copper-manganese and from elemental copper, nickel and manganese powders sintered in-house both matched the reference closely, with furnace regulation accounting for the visible trace drops.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#PrintedThermocouples, #TypeKTypeT, #ToleranceClassOne, #FurnaceSintering, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
Screen Printing Technology For Printed Electronics Manufacturing
More Highlights from the same talk.
04:48 - 06:22
Where does a 20% battery-production energy saving actually come from?
Where does a 20% battery-production energy saving actually come from?
The targeted 20% reduction in overall energy consumption is built from three contributions: around 20% less solvent that must be evaporated, around 10% less coated area through near-net-shape printing, and around 20% higher drying efficiency. Together these give around 40% reduced drying energy, which translates into roughly 20% energy-cost savings.
Those reductions are intended to lower OPEX and, through shorter drying areas or shorter drying furnaces, allow work in smaller areas and lower CAPEX. This is framed as a forecast tied to machinery arriving at the end of this year, not an already measured result.
For the printed-electrode printing platform, the plan uses a screen printer for double-sided coatings of flexible substrates. The energy case therefore combines reduced solvent, near-net-shape printing and higher drying efficiency on one platform, with the 20% overall energy reduction and 40% drying-energy reduction as stated targets.
In this short video, you can learn:
* About 20% less solvent to evaporate, about 10% less coated area from near-net-shape printing and about 20% higher drying efficiency combine into around 40% reduced drying energy.
* The resulting overall energy-consumption reduction is around 20%, stated as roughly 20% energy-cost savings and lower OPEX.
* Shorter drying areas or furnaces are intended to enable smaller footprints and lower CAPEX, with the machinery expected at the end of this year.
📋 **Clip Abstract** The 20% overall energy reduction comes from around 20% less solvent evaporation, around 10% less coated area via near-net-shape printing and around 20% higher drying efficiency, producing around 40% reduced drying energy and roughly 20% energy-cost savings. Shorter drying areas or furnaces are intended to lower OPEX and CAPEX, with the machinery described as a forecast for arrival at the end of this year and the printed-electrode platform using a screen printer for double-sided coatings on flexible substrates.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#ScreenPrinting, #NearNetShapePrinting, #SolventEvaporationReduction, #DryingEnergySavings, #PrintedElectronics, #BatteryProduction
10:39 - 12:23
Can thick electrodes be printed without cracking or killing C-rate?
Can thick electrodes be printed without cracking or killing C-rate?
Printing a 300 micron electrode rather than 30 microns changes how much solvent must leave the structure, and doing it wrong produces cracking. The answer is multilayer printing: solvent is extracted step by step between passes instead of all at once from a single thick layer.
The trade-off is explicit: thicker layers mean more capacity, but current-rate capability falls because ions and electrons travel longer distances — the difference between a 30 micron and a 300 micron electrode. That penalty is the core problem the printing approach has to solve.
Two levers are being worked on: a graduated design through the electrode thickness, and different recipes for the different printing steps. Multilayer printing makes both possible, because each pass can be formulated and deposited independently rather than one recipe serving the whole 300 micron stack.
In this short video, you can learn:
* Multilayer printing extracts solvent step by step, which is how cracking is avoided when electrodes are thickened.
* Moving from 30 to 300 microns raises capacity but costs current-rate capability because ion and electron paths grow longer.
* Graduated electrode designs and separate recipes per printing step are the routes being pursued to recover rate performance.
📋 **Clip Abstract** Thick electrodes buy capacity but bring solvent removal and rate limits. Multilayer printing with stepwise solvent extraction, graduated designs and per-pass recipes attacks both.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#ThickElectrodePrinting, #MultilayerScreenPrinting, #SolventRemovalControl, #GraduatedElectrodeDesign, #PrintedElectronics, #BatteryCellProduction
08:36 - 10:10
How much of a conventional battery electrode is inactive dead volume?
How much of a conventional battery electrode is inactive dead volume?
LFP energy density is not as good as NMC among the main active materials, but converting conventional designs into cyclone electrodes can lift LFP to another energy-density level relative to NMC. The comparison hinges on electrode thickness and how much electrode volume actually stores energy.
In nominal or conventional design, electrodes are quite thin. In that architecture only around 50% to 60% of the volume is used for storage. Preparing films in a thicker way can optimize these amounts to nearly 90%, changing the balance between active storage volume and inactive material.
Thicker films reduce the relative share of current collectors and separators. These are inactive materials needed for the battery, and avoiding them as much as possible helps energy density. The gain comes from using more of the electrode volume for storage rather than inactive components.
In this short video, you can learn:
* Conventional thin electrodes use only about 50% to 60% of their volume for storage.
* Thicker films can raise storage utilization to nearly 90%.
* Cyclone electrode designs aim to lift LFP energy density relative to NMC by reducing inactive current collectors and separators.
📋 **Clip Abstract** Conventional battery electrodes are thin, with only about 50% to 60% of volume used for storage. Converting designs into cyclone electrodes and preparing thicker films can optimize storage to nearly 90%, reducing inactive current collectors and separators and helping lift LFP energy density relative to NMC.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#CycloneElectrodes, #ThickerElectrodeFilms, #LFPEnergyDensity, #InactiveMaterialReduction, #BatteryElectrodes, #ScreenPrinting
More highlights from Mario Kohl
- ▶ Where does a 20% battery-production energy saving actually come from? · Electronics RESHAPED 2026 | Berlin
- ▶ How much of a conventional battery electrode is inactive dead volume? · Electronics RESHAPED 2026 | Berlin
- ▶ Can thick electrodes be printed without cracking or killing C-rate? · Electronics RESHAPED 2026 | Berlin
- ▶ What area capacity do printed LFP cathodes reach—and do separate print steps leave internal borders? · Electronics RESHAPED 2026 | Berlin
- ▶ Can a fully printed sodium-ion solid-state cell actually cycle? · Electronics RESHAPED 2026 | Berlin
- ▶ Why can't stacked slot-die coaters solve solvent removal in 300-micron thick electrodes? · Electronics RESHAPED 2026 | Berlin


