Mario Kohl | Fraunhofer IFAM: Can thick electrodes be printed without cracking or killing C-rate?
10:39 - 12:23
Other snippets from this talk
Summary of the clip:
Can thick electrodes be printed without cracking or killing C-rate?
Printing a 300 micron electrode rather than 30 microns changes how much solvent must leave the structure, and doing it wrong produces cracking. The answer is multilayer printing: solvent is extracted step by step between passes instead of all at once from a single thick layer.
The trade-off is explicit: thicker layers mean more capacity, but current-rate capability falls because ions and electrons travel longer distances β the difference between a 30 micron and a 300 micron electrode. That penalty is the core problem the printing approach has to solve.
Two levers are being worked on: a graduated design through the electrode thickness, and different recipes for the different printing steps. Multilayer printing makes both possible, because each pass can be formulated and deposited independently rather than one recipe serving the whole 300 micron stack.
In this short video, you can learn:
* Multilayer printing extracts solvent step by step, which is how cracking is avoided when electrodes are thickened.
* Moving from 30 to 300 microns raises capacity but costs current-rate capability because ion and electron paths grow longer.
* Graduated electrode designs and separate recipes per printing step are the routes being pursued to recover rate performance.
π **Clip Abstract** Thick electrodes buy capacity but bring solvent removal and rate limits. Multilayer printing with stepwise solvent extraction, graduated designs and per-pass recipes attacks both.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#ThickElectrodePrinting, #MultilayerScreenPrinting, #SolventRemovalControl, #GraduatedElectrodeDesign, #PrintedElectronics, #BatteryCellProduction
This is a highlight of the presentation:
Screen printing in battery production - New Opportunities
More Highlights from the same talk.
04:48 - 06:22
Where does a 20% battery-production energy saving actually come from?
Where does a 20% battery-production energy saving actually come from?
The targeted 20% reduction in overall energy consumption is built from three contributions: around 20% less solvent that must be evaporated, around 10% less coated area through near-net-shape printing, and around 20% higher drying efficiency. Together these give around 40% reduced drying energy, which translates into roughly 20% energy-cost savings.
Those reductions are intended to lower OPEX and, through shorter drying areas or shorter drying furnaces, allow work in smaller areas and lower CAPEX. This is framed as a forecast tied to machinery arriving at the end of this year, not an already measured result.
For the printed-electrode printing platform, the plan uses a screen printer for double-sided coatings of flexible substrates. The energy case therefore combines reduced solvent, near-net-shape printing and higher drying efficiency on one platform, with the 20% overall energy reduction and 40% drying-energy reduction as stated targets.
In this short video, you can learn:
* About 20% less solvent to evaporate, about 10% less coated area from near-net-shape printing and about 20% higher drying efficiency combine into around 40% reduced drying energy.
* The resulting overall energy-consumption reduction is around 20%, stated as roughly 20% energy-cost savings and lower OPEX.
* Shorter drying areas or furnaces are intended to enable smaller footprints and lower CAPEX, with the machinery expected at the end of this year.
π **Clip Abstract** The 20% overall energy reduction comes from around 20% less solvent evaporation, around 10% less coated area via near-net-shape printing and around 20% higher drying efficiency, producing around 40% reduced drying energy and roughly 20% energy-cost savings. Shorter drying areas or furnaces are intended to lower OPEX and CAPEX, with the machinery described as a forecast for arrival at the end of this year and the printed-electrode platform using a screen printer for double-sided coatings on flexible substrates.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#ScreenPrinting, #NearNetShapePrinting, #SolventEvaporationReduction, #DryingEnergySavings, #PrintedElectronics, #BatteryProduction
20:57 - 22:25
What area capacity do printed LFP cathodes reachβand do separate print steps leave internal borders?
What area capacity do printed LFP cathodes reachβand do separate print steps leave internal borders?
The example is an LFP cathode with current collectors and a double-sided coating. The reported area value is around three milliamps per square centimetre, described as 30% to 50% above the state of the art. The same printed electrode route can be increased to three and a half to six milliamps per square centimetre.
These electrodes were prepared with separate printing. The resulting stack shows no visible intermediate layers, no clear gradients and no borders between the single electrodes or printing steps. That matters because adhesion testing later showed failures occurring through non-adhesion to the current collectors, not through a structural defect inside the printed electrode.
The work also reports that different densifications can be used. The absence of internal borders is presented as important for the printed electrode's behaviour, while the observed failure mode points to the current-collector interface as the critical adhesion zone. These printed LFP cathode results are presented as the basis for new opportunities in battery production.
In this short video, you can learn:
* A double-sided printed LFP cathode is reported at around three milliamps per square centimetre, 30% to 50% above the state of the art.
* The reported range can be raised to three and a half to six milliamps per square centimetre.
* Separate printing steps showed no intermediate layers, gradients or borders, and adhesion failures were at the current collector rather than in the electrode structure.
π **Clip Abstract** Printed LFP cathodes with double-sided coatings are reported at around three milliamps per square centimetre, 30% to 50% above the state of the art, with a possible increase to three and a half to six. Separate printing steps produced no visible intermediate layers, gradients or borders, while adhesion failures occurred at the current collector rather than within the electrode structure.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#LFPCathode, #DoubleSidedCoating, #CurrentCollectorAdhesion, #SeparatePrintingSteps, #PrintedElectronics, #BatteryProduction
08:36 - 10:10
How much of a conventional battery electrode is inactive dead volume?
How much of a conventional battery electrode is inactive dead volume?
LFP energy density is not as good as NMC among the main active materials, but converting conventional designs into cyclone electrodes can lift LFP to another energy-density level relative to NMC. The comparison hinges on electrode thickness and how much electrode volume actually stores energy.
In nominal or conventional design, electrodes are quite thin. In that architecture only around 50% to 60% of the volume is used for storage. Preparing films in a thicker way can optimize these amounts to nearly 90%, changing the balance between active storage volume and inactive material.
Thicker films reduce the relative share of current collectors and separators. These are inactive materials needed for the battery, and avoiding them as much as possible helps energy density. The gain comes from using more of the electrode volume for storage rather than inactive components.
In this short video, you can learn:
* Conventional thin electrodes use only about 50% to 60% of their volume for storage.
* Thicker films can raise storage utilization to nearly 90%.
* Cyclone electrode designs aim to lift LFP energy density relative to NMC by reducing inactive current collectors and separators.
π **Clip Abstract** Conventional battery electrodes are thin, with only about 50% to 60% of volume used for storage. Converting designs into cyclone electrodes and preparing thicker films can optimize storage to nearly 90%, reducing inactive current collectors and separators and helping lift LFP energy density relative to NMC.
About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
π
Save the date: 9 and 10 June 2027
π Mountain View, California (Silicon Valley)
π Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/electronicsreshaped
#CycloneElectrodes, #ThickerElectrodeFilms, #LFPEnergyDensity, #InactiveMaterialReduction, #BatteryElectrodes, #ScreenPrinting
More highlights from Mario Kohl
- βΆ How do the disperse and continuous phases of a functional paste interact to determine its rheological behavior for screen printing? Β· The Future of Electronics RESHAPED 2025 | Berlin
- βΆ Why do printed thermocouples offer a distinct calibration advantage over traditional RTDs like PT100 or PT1000 sensors? Β· The Future of Electronics RESHAPED 2025 | Berlin
- βΆ Do printed Type K and Type T thermocouples hold tolerance class one against wire references, and where do they drift? Β· The Future of Electronics RESHAPED 2025 | Berlin
- βΆ How does hybrid manufacturing combine printed conductive tracks with conventional SMD components to increase design and production flexibility? Β· The Future of Electronics RESHAPED 2025 | Berlin
- βΆ Why does screen printing beat slot die coating for manufacturing high-energy battery electrodes? Β· The Future of Electronics RESHAPED 2025 | Berlin


