top of page

Mario Kohl

Fraunhofer IFAM

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Mario Kohl | Fraunhofer IFAM: Why does screen printing beat slot die coating for manufacturing high-energy battery electrodes?

38:34 - 40:53

Other snippets from this talk

Summary of the clip:

Why does screen printing beat slot die coating for manufacturing high-energy battery electrodes?

The conventional electrode design carries roughly 28% separator and 70% current collector, leaving only about 56% real active material that is capable of storing energy. Screen printing an anode changes that ratio substantially: because thicker electrodes can be printed, the amount of real active material is highly enhanced. The starting point is a screen printed anode, and the goal is high energy electrodes built from a design where the inactive components no longer dominate the stack.

Slot die coating is the standard process here, but its viscosity is limited to a certain amount, and those slurries carry quite a lot of solvent β€” a ratio this approach sets out to change. Screen printing tolerates higher solid contents compared with the state of the art. That shifts the formulation away from solvent-heavy pastes and toward the denser deposits needed for high energy electrodes.

Screen printing also allows printing multiple times, and specifically a print-dry-print-dry sequence repeated as needed. That directly tackles one effect seen in the conventional route: cracks forming in the electrodes during the drying process. Building the layer in successive passes, each dried before the next, is the practical answer. It is a process route built on repeatability rather than a single thick wet deposit.

In this short video, you can learn:
* Conventional electrode stacks yield only about 56% real active material, with separator and current collector taking roughly 28% and 70%.
* Slot die coating is constrained by a limited viscosity window and solvent-heavy slurries, whereas screen printing supports higher solid contents than the state of the art.
* Repeating print-dry-print-dry passes in screen printing mitigates the cracking that appears in conventional electrodes during drying.

πŸ“‹ **Clip Abstract** Screen printing is positioned as the route to high energy battery electrodes, replacing slot die coating as the standard deposition step. Higher solid contents plus repeated print-dry cycles raise the active material share and suppress drying cracks.

About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin

πŸ—“οΈ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped

#ScreenPrintedAnodes, #HighSolidContentSlurry, #SlotDieCoating, #PrintDryCycles, #PrintedElectronics, #BatteryManufacturing

This is a highlight of the presentation:

Screen Printing Technology For Printed Electronics Manufacturing

The Future of Electronics RESHAPED 2025 | Berlin

​

22-23 October 2025

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

04:48 - 06:22

Where does a 20% battery-production energy saving actually come from?

Where does a 20% battery-production energy saving actually come from?

The targeted 20% reduction in overall energy consumption is built from three contributions: around 20% less solvent that must be evaporated, around 10% less coated area through near-net-shape printing, and around 20% higher drying efficiency. Together these give around 40% reduced drying energy, which translates into roughly 20% energy-cost savings.

Those reductions are intended to lower OPEX and, through shorter drying areas or shorter drying furnaces, allow work in smaller areas and lower CAPEX. This is framed as a forecast tied to machinery arriving at the end of this year, not an already measured result.

For the printed-electrode printing platform, the plan uses a screen printer for double-sided coatings of flexible substrates. The energy case therefore combines reduced solvent, near-net-shape printing and higher drying efficiency on one platform, with the 20% overall energy reduction and 40% drying-energy reduction as stated targets.

In this short video, you can learn:
* About 20% less solvent to evaporate, about 10% less coated area from near-net-shape printing and about 20% higher drying efficiency combine into around 40% reduced drying energy.
* The resulting overall energy-consumption reduction is around 20%, stated as roughly 20% energy-cost savings and lower OPEX.
* Shorter drying areas or furnaces are intended to enable smaller footprints and lower CAPEX, with the machinery expected at the end of this year.

πŸ“‹ **Clip Abstract** The 20% overall energy reduction comes from around 20% less solvent evaporation, around 10% less coated area via near-net-shape printing and around 20% higher drying efficiency, producing around 40% reduced drying energy and roughly 20% energy-cost savings. Shorter drying areas or furnaces are intended to lower OPEX and CAPEX, with the machinery described as a forecast for arrival at the end of this year and the printed-electrode platform using a screen printer for double-sided coatings on flexible substrates.

About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#ScreenPrinting, #NearNetShapePrinting, #SolventEvaporationReduction, #DryingEnergySavings, #PrintedElectronics, #BatteryProduction

10:39 - 12:23

Can thick electrodes be printed without cracking or killing C-rate?

Can thick electrodes be printed without cracking or killing C-rate?

Printing a 300 micron electrode rather than 30 microns changes how much solvent must leave the structure, and doing it wrong produces cracking. The answer is multilayer printing: solvent is extracted step by step between passes instead of all at once from a single thick layer.

The trade-off is explicit: thicker layers mean more capacity, but current-rate capability falls because ions and electrons travel longer distances β€” the difference between a 30 micron and a 300 micron electrode. That penalty is the core problem the printing approach has to solve.

Two levers are being worked on: a graduated design through the electrode thickness, and different recipes for the different printing steps. Multilayer printing makes both possible, because each pass can be formulated and deposited independently rather than one recipe serving the whole 300 micron stack.

In this short video, you can learn:
* Multilayer printing extracts solvent step by step, which is how cracking is avoided when electrodes are thickened.
* Moving from 30 to 300 microns raises capacity but costs current-rate capability because ion and electron paths grow longer.
* Graduated electrode designs and separate recipes per printing step are the routes being pursued to recover rate performance.

πŸ“‹ **Clip Abstract** Thick electrodes buy capacity but bring solvent removal and rate limits. Multilayer printing with stepwise solvent extraction, graduated designs and per-pass recipes attacks both.

About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#ThickElectrodePrinting, #MultilayerScreenPrinting, #SolventRemovalControl, #GraduatedElectrodeDesign, #PrintedElectronics, #BatteryCellProduction

08:36 - 10:10

How much of a conventional battery electrode is inactive dead volume?

How much of a conventional battery electrode is inactive dead volume?

LFP energy density is not as good as NMC among the main active materials, but converting conventional designs into cyclone electrodes can lift LFP to another energy-density level relative to NMC. The comparison hinges on electrode thickness and how much electrode volume actually stores energy.

In nominal or conventional design, electrodes are quite thin. In that architecture only around 50% to 60% of the volume is used for storage. Preparing films in a thicker way can optimize these amounts to nearly 90%, changing the balance between active storage volume and inactive material.

Thicker films reduce the relative share of current collectors and separators. These are inactive materials needed for the battery, and avoiding them as much as possible helps energy density. The gain comes from using more of the electrode volume for storage rather than inactive components.

In this short video, you can learn:
* Conventional thin electrodes use only about 50% to 60% of their volume for storage.
* Thicker films can raise storage utilization to nearly 90%.
* Cyclone electrode designs aim to lift LFP energy density relative to NMC by reducing inactive current collectors and separators.

πŸ“‹ **Clip Abstract** Conventional battery electrodes are thin, with only about 50% to 60% of volume used for storage. Converting designs into cyclone electrodes and preparing thicker films can optimize storage to nearly 90%, reducing inactive current collectors and separators and helping lift LFP energy density relative to NMC.

About the speaker:
* Speaker: Mario Kohl
* Company: Fraunhofer IFAM
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#CycloneElectrodes, #ThickerElectrodeFilms, #LFPEnergyDensity, #InactiveMaterialReduction, #BatteryElectrodes, #ScreenPrinting

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page