top of page

Mark Poliks

Binghamton University

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Mark Poliks | Binghamton University: How does the choice of silver ink and carbon resistor materials affect the overall performance and reliability of the sweat sensor in real-world conditions?

00:09:19 - 00:09:29

Other snippets from this talk

Summary of the clip:

How does the choice of silver ink and carbon resistor materials affect the overall performance and reliability of the sweat sensor in real-world conditions?

The speaker describes the materials used in the sweat sensor, noting that silver ink is used to print the conductor traces. The sensor attaches to the device through these traces. A series of carbon resistors are printed on top, bridging the circuits.

The speaker explains that carbon is sensitive to moisture, and as sweat flows in, the carbon resistors react. This reaction is used to measure the sweat volume and electrolyte concentrations. The speaker references previous discussions about the use of carbon in similar applications.

The presentation includes a slide showing the electrode design and the materials used. The speaker emphasizes the importance of selectivity and sensitivity in the printed device, demonstrating that the system can accurately measure sodium and potassium concentrations. The next step involves testing the device in real-world conditions with individuals engaged in physical activity.

In this short video, you can learn:

* Silver ink is used for printing conductor traces in the sensor.
* Carbon resistors are used to measure sweat volume due to their sensitivity to moisture.
* The sensor demonstrates good selectivity and sensitivity in measuring electrolyte concentrations.

๐Ÿ“‹ **Clip Abstract** This segment focuses on the materials and design of the sweat sensor electrodes, highlighting the use of silver ink for conductivity and carbon resistors for moisture sensitivity. It also mentions the successful testing of the sensor's selectivity and sensitivity.
๐Ÿ”— Link in comments ๐Ÿ‘‡

#SilverInk, #CarbonResistors, #MoistureSensing, #ElectrolyteSensing, #Biosensors, #WearableSensors

This is a highlight of the presentation:

​

The Future of Electronics RESHAPED USA | Boston 2025

​

​

UMass Boston

Organised By:

TechBlick

​

More Highlights from the same talk.

01:28 - 02:25

Why do tethered snake robots and borescopes fail to inspect sealed industrial surfaces without creating cable knots?

Why do tethered snake robots and borescopes fail to inspect sealed industrial surfaces without creating cable knots?

Equipment that is not easily taken apart on a regular basis hides internal surfaces where issues may start to develop. The traditional tools are tethered snake robots and borescopes: long tubes with a camera on one end and a monitor on the other. Both are difficult to insert and offer limited steering and guidance.

Longer cables amplify the failure mode: an actual example shows a borescope creating a knot of cables and other wiring inside such a device after too many passes. The clip calls this a serious problem and a clear limitation on how inspection can be done.

The stated inspiration is soft robotics: an artificial creepy crawler that could enter constrained spaces. The target is inspection of surfaces that are otherwise hard to access without disassembly. The contrast is with tethered, tube-based tools whose insertion, steering and cable management are all called out as weak points.

In this short video, you can learn:
* Tethered snake robots and borescopes are difficult to insert and provide little steering and guidance.
* Longer borescope cables can create a knot of cables and wiring inside the equipment.
* Soft robotics inspired the idea of an artificial creepy crawler that could enter confined spaces.

๐Ÿ“‹ **Clip Abstract** The clip frames internal inspection as a problem for equipment that is not regularly disassembled: tethered snake robots and borescopes are hard to insert, hard to steer and prone to cable knots. It presents soft robotics, specifically an artificial creepy crawler, as the inspiration for entering these constrained spaces.

About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
๐Ÿ“… Save the date: 9 and 10 June 2027
๐Ÿ“ Mountain View, California (Silicon Valley)
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
๐Ÿ“… Save the date: 20 and 21 October 2027
๐Ÿ“ Berlin, Germany
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshaped

#BorescopeInspection, #TetheredSnakeRobots, #CableKnotting, #CreepyCrawlerRobot, #SoftRobotics, #IndustrialInspection

10:28 - 12:52

What printed layer stack makes a soft e-skin pressure node that plateaus cleanly at 200 psi?

What printed layer stack makes a soft e-skin pressure node that plateaus cleanly at 200 psi?

The team screened Covestro, Lubrizol and subs/materials for low stress relaxation, low hysteresis and low-to-medium modulus, then modeled before building and testing systems. Inks also had to be compatible with the particular application and work with the stiffening scheme.

Each sensory nodule used a printed silver bottom electrode, a stiffer material on top, a via filled with compressible carbon, and a top electrodeโ€”a sandwich resting in nodes. This lets the soft robot drag or turn into a crevice and build a three-dimensional contact/pressure map. The team started simple and is advancing to a more complicated array.

Compression testing evaluated combinations, reversibility and repeated pressures at varying frequencies. The all-printed semi-soft system behaved relatively well, with nice curves showing resistance changes under pressure changes. These carbon sensors max out near 200 psi and show a very clean plateau; minimum-force sensing comes next.

In this short video, you can learn:
* Material screening prioritized low stress relaxation, low hysteresis and low-to-medium modulus across Covestro, Lubrizol and subs/materials.
* The pressure node is a printed silver bottom electrode, stiff material, compressible carbon via fill and top electrode sandwich.
* Compression tests showed resistance changes with pressure, reversibility, and a clean plateau at about 200 psi for carbon sensors.

๐Ÿ“‹ **Clip Abstract** A soft robotic e-skin pressure node is built as a printed sandwich: silver bottom electrode, stiff material, compressible carbon via fill and top electrode. Screening Covestro, Lubrizol and subs/materials for low stress relaxation, low hysteresis and low-to-medium modulus, plus compression tests, yielded clean resistance-versus-pressure curves and a plateau near 200 psi.

About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
๐Ÿ“… Save the date: 9 and 10 June 2027
๐Ÿ“ Mountain View, California (Silicon Valley)
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
๐Ÿ“… Save the date: 20 and 21 October 2027
๐Ÿ“ Berlin, Germany
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshaped

#PrintedSilverElectrode, #CompressibleCarbonVia, #PressurePlateau200PSI, #ESkinPressureNode, #SoftRobotics, #PrintedSensors

05:58 - 07:53

How does one printed liquid-metal ink deliver directional strain sensing and linear temperature sensing from 25 to 100ยฐC?

How does one printed liquid-metal ink deliver directional strain sensing and linear temperature sensing from 25 to 100ยฐC?

The work uses soft substrates such as TPU and polymer-coated, encapsulated liquid-metal materials, including Liquidwire and Blue Halo versions linked to Chris Taberโ€™s material. These print well with simple dispense tools, form uniform transmission lines, and can be pre-strained, cured and activated. They are easy to connect to, which matters for repeated sensor builds.

Mechanical tests show distinct responses to horizontal versus vertical movement, so directional strain is inferred from changing mechanical properties as the E Ink-type material is stretched or sheared, not only from camera images. Biaxial testing also worked well. The sensor characterization covered temperatures from 25 to 100 degrees C, and all results looked quite promising.

A surprising secondary advantage is that the same printed liquid-metal sensor behaves very linearly over the temperature ranges of interest, so it can also serve as a temperature sensor. The same structure used to monitor directional strain can therefore provide a linear temperature response from 25 to 100 degrees C.

In this short video, you can learn:
* Polymer-coated encapsulated liquid-metal inks print uniformly with simple dispense tools and can be pre-strained, cured and activated.
* Directional strain is distinguished by different horizontal and vertical mechanical responses, with biaxial testing also successful.
* The same sensor shows linear temperature behavior from 25 to 100 degrees C, adding temperature sensing as a secondary advantage.

๐Ÿ“‹ **Clip Abstract** Soft TPU substrates and encapsulated liquid-metal inks are printed into uniform, connectable transmission lines that are pre-strained, cured and activated for sensing. Mechanical testing distinguishes horizontal and vertical strain, biaxial testing works well, and the same device behaves linearly as a temperature sensor from 25 to 100 degrees C.

About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
๐Ÿ“… Save the date: 9 and 10 June 2027
๐Ÿ“ Mountain View, California (Silicon Valley)
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
๐Ÿ“… Save the date: 20 and 21 October 2027
๐Ÿ“ Berlin, Germany
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshaped

#LiquidMetalInk, #DirectionalStrainSensing, #LinearTemperatureSensing, #BiaxialTesting, #SoftRobotics, #PrintedElectronics


Other talks by Mark Poliks


More highlights from Mark Poliks

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page