Mark Poliks | Binghamton University: How does one printed liquid-metal ink deliver directional strain sensing and linear temperature sensing from 25 to 100°C?
05:58 - 07:53
Other snippets from this talk
Summary of the clip:
How does one printed liquid-metal ink deliver directional strain sensing and linear temperature sensing from 25 to 100°C?
The work uses soft substrates such as TPU and polymer-coated, encapsulated liquid-metal materials, including Liquidwire and Blue Halo versions linked to Chris Taber’s material. These print well with simple dispense tools, form uniform transmission lines, and can be pre-strained, cured and activated. They are easy to connect to, which matters for repeated sensor builds.
Mechanical tests show distinct responses to horizontal versus vertical movement, so directional strain is inferred from changing mechanical properties as the E Ink-type material is stretched or sheared, not only from camera images. Biaxial testing also worked well. The sensor characterization covered temperatures from 25 to 100 degrees C, and all results looked quite promising.
A surprising secondary advantage is that the same printed liquid-metal sensor behaves very linearly over the temperature ranges of interest, so it can also serve as a temperature sensor. The same structure used to monitor directional strain can therefore provide a linear temperature response from 25 to 100 degrees C.
In this short video, you can learn:
* Polymer-coated encapsulated liquid-metal inks print uniformly with simple dispense tools and can be pre-strained, cured and activated.
* Directional strain is distinguished by different horizontal and vertical mechanical responses, with biaxial testing also successful.
* The same sensor shows linear temperature behavior from 25 to 100 degrees C, adding temperature sensing as a secondary advantage.
📋 **Clip Abstract** Soft TPU substrates and encapsulated liquid-metal inks are printed into uniform, connectable transmission lines that are pre-strained, cured and activated for sensing. Mechanical testing distinguishes horizontal and vertical strain, biaxial testing works well, and the same device behaves linearly as a temperature sensor from 25 to 100 degrees C.
About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#LiquidMetalInk, #DirectionalStrainSensing, #LinearTemperatureSensing, #BiaxialTesting, #SoftRobotics, #PrintedElectronics
This is a highlight of the presentation:
Printed Multimodal Sensing e-Skin for Soft Robotics for use in Navigation and Inspection of Complex Industrial Systems
More Highlights from the same talk.
01:28 - 02:25
Why do tethered snake robots and borescopes fail to inspect sealed industrial surfaces without creating cable knots?
Why do tethered snake robots and borescopes fail to inspect sealed industrial surfaces without creating cable knots?
Equipment that is not easily taken apart on a regular basis hides internal surfaces where issues may start to develop. The traditional tools are tethered snake robots and borescopes: long tubes with a camera on one end and a monitor on the other. Both are difficult to insert and offer limited steering and guidance.
Longer cables amplify the failure mode: an actual example shows a borescope creating a knot of cables and other wiring inside such a device after too many passes. The clip calls this a serious problem and a clear limitation on how inspection can be done.
The stated inspiration is soft robotics: an artificial creepy crawler that could enter constrained spaces. The target is inspection of surfaces that are otherwise hard to access without disassembly. The contrast is with tethered, tube-based tools whose insertion, steering and cable management are all called out as weak points.
In this short video, you can learn:
* Tethered snake robots and borescopes are difficult to insert and provide little steering and guidance.
* Longer borescope cables can create a knot of cables and wiring inside the equipment.
* Soft robotics inspired the idea of an artificial creepy crawler that could enter confined spaces.
📋 **Clip Abstract** The clip frames internal inspection as a problem for equipment that is not regularly disassembled: tethered snake robots and borescopes are hard to insert, hard to steer and prone to cable knots. It presents soft robotics, specifically an artificial creepy crawler, as the inspiration for entering these constrained spaces.
About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#BorescopeInspection, #TetheredSnakeRobots, #CableKnotting, #CreepyCrawlerRobot, #SoftRobotics, #IndustrialInspection
15:19 - 17:24
Can an impedance skin detect voids and delamination hidden beneath a composite surface as the robot crawls?
Can an impedance skin detect voids and delamination hidden beneath a composite surface as the robot crawls?
The approach is dielectric: a homogeneous composite should have a uniform dielectric constant set by reinforcement and volume. Delamination or voids change that dielectric constant. The project builds on Felipe’s work in Ana’s lab at Berkeley using particle-filled materials, then Sunrise Material’s magnetically oriented particles to sense frequency-dependent resistance, i.e. impedance.
Tests span different impedance regimes. The team has not worked with cracked composites; instead, holes were made in substrates. By comparing difference zones in impedance numbers, they distinguish large numbers of holes, no holes, or a moderate number—both for dura stone material and a polished carbon-fiber type material, which both appear very feasible.
The skin is worn on the bottom side. As the robot crawls, it can sense the integrity of composites below the surface and assess whether potential cracks would require additional—the excerpt ends at that word. No further field result is stated in the clip.
In this short video, you can learn:
* Delamination and voids alter a composite’s dielectric constant, giving a simple dielectric-change target for a crawling robot without X-ray or complicated sensors.
* Magnetically oriented particle-filled materials let the skin sense changes in the frequency dependence of resistance, i.e. impedance.
* Hole tests on dura stone and polished carbon-fiber type materials showed distinguishable impedance difference zones for no, moderate and large numbers of holes.
📋 **Clip Abstract** An impedance skin for a crawling robot uses dielectric changes in composites to detect voids and delamination without X-ray or complicated sensors. It builds on particle-filled and magnetically oriented materials, and hole tests on dura stone and polished carbon-fiber type substrates show distinguishable impedance zones for no, moderate and large numbers of holes.
About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#ImpedanceSkin, #MagneticallyOrientedParticles, #ImpedanceDifferenceZones, #DuraStoneSubstrate, #SoftRobotics, #CompositeInspection
10:28 - 12:52
What printed layer stack makes a soft e-skin pressure node that plateaus cleanly at 200 psi?
What printed layer stack makes a soft e-skin pressure node that plateaus cleanly at 200 psi?
The team screened Covestro, Lubrizol and subs/materials for low stress relaxation, low hysteresis and low-to-medium modulus, then modeled before building and testing systems. Inks also had to be compatible with the particular application and work with the stiffening scheme.
Each sensory nodule used a printed silver bottom electrode, a stiffer material on top, a via filled with compressible carbon, and a top electrode—a sandwich resting in nodes. This lets the soft robot drag or turn into a crevice and build a three-dimensional contact/pressure map. The team started simple and is advancing to a more complicated array.
Compression testing evaluated combinations, reversibility and repeated pressures at varying frequencies. The all-printed semi-soft system behaved relatively well, with nice curves showing resistance changes under pressure changes. These carbon sensors max out near 200 psi and show a very clean plateau; minimum-force sensing comes next.
In this short video, you can learn:
* Material screening prioritized low stress relaxation, low hysteresis and low-to-medium modulus across Covestro, Lubrizol and subs/materials.
* The pressure node is a printed silver bottom electrode, stiff material, compressible carbon via fill and top electrode sandwich.
* Compression tests showed resistance changes with pressure, reversibility, and a clean plateau at about 200 psi for carbon sensors.
📋 **Clip Abstract** A soft robotic e-skin pressure node is built as a printed sandwich: silver bottom electrode, stiff material, compressible carbon via fill and top electrode. Screening Covestro, Lubrizol and subs/materials for low stress relaxation, low hysteresis and low-to-medium modulus, plus compression tests, yielded clean resistance-versus-pressure curves and a plateau near 200 psi.
About the speaker:
* Speaker: Mark Poliks
* Company: Binghamton University
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#PrintedSilverElectrode, #CompressibleCarbonVia, #PressurePlateau200PSI, #ESkinPressureNode, #SoftRobotics, #PrintedSensors
About this talk
→ Printed Multimodal Sensing e-Skin for Soft Robotics for use in Navigation and Inspection of Complex Industrial Systems · Mark Poliks · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Mark Poliks
- Smart, Reusable Catheter System for Longitudinal Urinary Monitoring at the Point of Care · Electronics RESHAPED USA 2026
- Fabrication of Multi-Sensor Vital Sign Patches for Ambulatory Care · Innovations Festival: Printed, Flexible, Hybrid, 3D, Wearable, & Textile Electronics 2023
More highlights from Mark Poliks
- ▶ How do you package hair-thin wires and resistive sensors inside a 5mm reusable catheter tip? · Future of Electronics RESHAPED USA 2026
- ▶ Can chemical sterilization actually improve the electrical performance of a wire-based pH sensor? · Future of Electronics RESHAPED USA 2026
- ▶ How do you design a flexible, wrap-around pH sensor for cylindrical medical devices? · Future of Electronics RESHAPED USA 2026
- ▶ How does the all-printed electrode design impact the sensitivity and long-term stability of the sodium and potassium measurements? · The Future of Electronics RESHAPED USA | Boston 2025
- ▶ What are the key material properties and design considerations for the wick structure to ensure efficient sweat absorption and transport to the sensors? · The Future of Electronics RESHAPED USA | Boston 2025
- ▶ How does the choice of silver ink and carbon resistor materials affect the overall performance and reliability of the sweat sensor in real-world conditions? · The Future of Electronics RESHAPED USA | Boston 2025


