Maryam Bari | PINA CREATION: Why does sputtering still dominate ITO, and what technical limits create room for printable nanoinks?
03:15 - 04:58
Other snippets from this talk
Summary of the clip:
Why does sputtering still dominate ITO, and what technical limits create room for printable nanoinks?
Sputtering and vacuum deposition dominate the current ITO market because they deliver high conductivity, good optical transparency, thin-film quality and thickness and an established industry. The speaker acknowledges these advantages before asking whether another route can replace or sit beside them. The limits appear when ITO must be deposited on sensitive layers, when equipment cost is compared with other layers, and when flexible formats face size limits.
The direct technical constraint is deposition onto sensitive materials: sputtering ITO over perovskite materials or an organic absorber can damage the layers underneath. A second constraint is economic and material-based: indium is rare and expensive, and sputtering is a lossy process rather than a concentrated coating technique. Those two issues create the opening for printable ITO nanoinks.
Equipment expense and flexible-format size limitations add to the case against relying only on sputtered ITO. The speaker also notes that although flexible ITO exists in the market, size remains a limitation. The opportunity for printable ITO nanoinks is clear, but the speaker closes by contrasting an easy name with making the nanoinks.
In this short video, you can learn:
* Sputtering delivers high conductivity, optical transparency and thin-film quality, but it can damage perovskite or organic absorber layers.
* Indium scarcity and expense, plus sputter loss, create a materials and cost case for printable ITO nanoinks.
* Flexible ITO exists, yet size limits and expensive equipment keep the sputtering route from covering every application.
📋 **Clip Abstract** The clip contrasts established vacuum-deposition and sputtering ITO with the limitations that open space for printable ITO nanoinks. It cites damage to perovskite and organic absorber layers, expensive equipment, flexible-size limits, indium scarcity and sputter loss as drivers, while noting that making the nanoinks is not as easy as naming them.
About the speaker:
* Speaker: Maryam Bari
* Company: PINA CREATION
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ITONanoinks, #PrintableITO, #VacuumSputtering, #IndiumScarcity, #PerovskiteSolar, #OrganicPhotovoltaics
This is a highlight of the presentation:
Development of Printable Indium Tin OxideI(TO) Nano Inks for Low-Temperature Transparent Conductive Films
21 and 22 OCT 2026
Estrel, Berlin
Organised By:
More Highlights from the same talk.
02:34 - 04:12
Nanoparticles alone aren't an ink — which formulation parameters actually set conductivity, work function and device performance?
Nanoparticles alone aren't an ink — which formulation parameters actually set conductivity, work function and device performance?
The ink is not just nanoparticles such as zinc oxide nano ink; it is a combination of elements that must be engineered and optimized. The nanoparticle contribution includes size, distribution, crystallinity, defect density, phase purity and, importantly, surface chemistry. These factors affect conductivity, work function, charge mobility and charge concentration, and therefore device performance.
The solvent is equally important. Its kind, rheology and viscosity determine whether a stable nano ink can be created and maintained over time. Nanoparticle engineering and solvent selection are therefore not separate: together they set the ink's stability and the electronic properties that feed into device performance.
Nanoparticle engineering focuses on particle size, oxygen vacancy, surface defect and crystal structure. These are listed as factors that affect electronic properties such as conductivity, work function, charge mobility and charge concentration. The resulting device performance depends on the application: solar cells, LED, OLED or other sensors, within a $100 billion market.
In this short video, you can learn:
* Zinc oxide nano ink is not just nanoparticles; it is a combination of engineered elements including solvent.
* Nanoparticle size, distribution, crystallinity, defect density, phase purity and surface chemistry all affect electronic properties such as conductivity, work function, charge mobility and charge concentration.
* Solvent kind, rheology and viscosity govern stable nano ink over time and, with nanoparticles, device performance.
📋 **Clip Abstract** This clip explains that nano ink must be engineered as a combination of nanoparticles and solvent, not treated as nanoparticles alone. It links nanoparticle size, oxygen vacancy, surface defect and crystal structure, plus solvent rheology and viscosity, to conductivity, work function, charge mobility, charge concentration and device performance in solar cells, LEDs, OLEDs and sensors.
About the speaker:
* Speaker: Maryam Bari
* Company: PINA Creation Inc.
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#ZincOxideNanoInk, #NanoparticleSurfaceChemistry, #SolventRheology, #DevicePerformance, #NanoInks, #SolarDisplaySensors
04:57 - 06:42
Can printable ITO nanoinks beat sputtering on material use, energy, manufacturing cost and CO2?
Can printable ITO nanoinks beat sputtering on material use, energy, manufacturing cost and CO2?
The target is an ITO ink that prints at 150 °C in ambient air—no vacuum and no controlled environment—while delivering both transparency and conductivity. The speaker says the name is easy, but making ITO nanoinks with low sheet resistance is not. The research team therefore compared whether printable ITO is worth pursuing across cost, properties and manufacturing.
That comparison used more than 30 industry and paper references on ITO, including sputtering. The results separate nanoink, shown in blue, from vacuum ITO or sputtering, shown in black. Across material usage, energy consumption, manufacturing cost and the environmental measure of CO2, the nanoink route is better than sputtering.
So the case for printable ITO is not only a property question; it is a manufacturing and environmental comparison. The segment presents the nanoink as better than sputtering on material usage, energy consumption, manufacturing cost and CO2. It does not give individual values in this segment, but it frames the low-temperature ambient print route as the route under evaluation.
In this short video, you can learn:
* The target is 150 °C ambient printing with no vacuum and no controlled environment.
* Low sheet resistance is the difficult part of making printable ITO nanoinks.
* Across more than 30 industry and paper references, nanoink was better than vacuum ITO or sputtering on material usage, energy consumption, manufacturing cost and CO2.
📋 **Clip Abstract** Printable ITO nanoinks are being evaluated against vacuum ITO and sputtering for low-temperature ITO with transparency and conductivity. The cited comparison, drawing on more than 30 industry and paper references, reports better material usage, energy consumption, manufacturing cost and CO2 for the nanoink route.
About the speaker:
* Speaker: Maryam Bari
* Company: PINA CREATION
* Event: Perovskite Connect 2026 | Berlin
* Location: Estrel, Berlin
Save the date: Perovskite Connect 2027 | 20 and 21 OCT 2027 | Berlin
Co-located with the Future of Electronics RESHAPED conference and exhibition
Learn more: https://www.techblick.com/perovskiteconnect
Intestered in exhibiting: learn more here: https://www.techblick.com/perovskiteconnect
#ITONanoinks, #PrintableITO, #LowTemperatureITO, #SheetResistance, #PerovskiteSolarCells, #TransparentConductiveFilms
09:00 - 10:28
Why did the first nickel oxide ink underperform, and what changed in version two?
Why did the first nickel oxide ink underperform, and what changed in version two?
Tin oxide nano ink work reached a 10% nanoparticle concentration. Nickel oxide is described as challenging. The first nickel oxide version drew unsatisfying customer feedback: device stacks performed badly, or an extra interlayer was needed to show performance. Investigation linked the problem to surface chemistry altering the work function, which was not comparable and appeared lower, explaining the poor device result.
The second nickel oxide version was launched very recently. It has higher conductivity, a better work function, and a longer shelf than the first. More importantly, it can be annealed at 100 Celsius. That followed investigation of surface chemistry and its impact on work function in version one.
ITO nano inks are under development to produce printable, transparent, conductive films and replace sputtering. The aim is to use them on both flexible and rigid substrates at low temperature. The stated goal is below 200 Celsius. Tin oxide already achieved a 10% nanoparticle concentration.
In this short video, you can learn:
* The first nickel oxide version failed to satisfy customers because surface chemistry shifted its work function lower, making device stacks underperform unless another interlayer was used.
* The second nickel oxide version reports higher conductivity, better work function, longer shelf, and 100 Celsius annealing.
* Tin oxide nanoparticle concentration reached 10%, while ITO nano inks are being developed for printable transparent conductive films that replace sputtering on flexible and rigid substrates at low temperature with a below-200-Celsius goal.
📋 **Clip Abstract** Metal oxide nano inks can change device performance, but the first nickel oxide version underperformed because surface chemistry lowered its work function and customers needed another interlayer. A second nickel oxide version now claims higher conductivity, better work function, longer shelf, and 100 Celsius annealing, while tin oxide reached 10% nanoparticle concentration and ITO inks target printable transparent conductive films below 200 Celsius.
About the speaker:
* Speaker: Maryam Bari
* Company: PINA Creation Inc.
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#NickelOxideInk, #TinOxideNanoparticles, #WorkFunctionControl, #LowTemperatureAnnealing, #PrintedElectronics, #AdditiveElectronics
About this talk
→ Development of Printable Indium Tin OxideI(TO) Nano Inks for Low-Temperature Transparent Conductive Films · Maryam Bari · Perovskite Connect 2026
Other talks by Maryam Bari
- How Metal Oxide Nano Inks Can Improve Device Performance and Simplify Manufacturing · TechBlick Innovations Festival July 2026
- Bridging the Lab-to-Fab Gap: HowTin Oxide Nano Inks Drive Perovskite Commercialization? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- Boosting Stability and Efficiency in Perovskite and Organic Solar Cells through Scalable Metal Oxide Nano Inks · The Future of Electronics RESHAPED 2025
More highlights from Maryam Bari
- ▶ Nanoparticles alone aren't an ink — which formulation parameters actually set conductivity, work function and device performance? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Why did the first nickel oxide ink underperform, and what changed in version two? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Why are traditional metal oxides failing the commercialization curve for flexible perovskite solar cells? · Perovskite Connect 2025
- ▶ How do you achieve a 2-nanometer crystalline grain size in low-temperature solution-processed thin films? · Perovskite Connect 2025
- ▶ How do you prevent water-based transport inks from destroying moisture-sensitive perovskite solar cells? · Perovskite Connect 2025


