Sebastian Gepp | Bopla Gehäuse Systeme GmbH: Where must a transparent temperature sensor sit to measure the heater, not beside it, without black spots or wasted energy?
11:05 - 12:34
Other snippets from this talk
Summary of the clip:
Where must a transparent temperature sensor sit to measure the heater, not beside it, without black spots or wasted energy?
In mining, one of the oldest transparent heaters had no temperature sensor in its first revision; the second added one because climate change and gold-mining operations run continuously. A printed PTC element served as a temperature fuse, with a control unit. The remaining issue was a black spot in the field of view, which prevented laser penetration through the window.
For an Airbus window, the temperature sensor must be as close to the heater as possible—thermodynamics dictates it—but not on the heater. The tricky part is measuring the heater itself rather than the area next to it. This proximity constraint is the same in each case.
In heater displays, the small NTC sits under the black bezel, where there is usually no heater. Enlarging the heater to cover that region wastes energy—exactly what customers come to avoid. They need a heating solution that saves energy, so sensor placement and heater extent must be reconciled.
In this short video, you can learn:
* A printed PTC element can act as a temperature fuse in a transparent heater, with a control unit.
* The sensor must be near the heater but not on it, because measuring the heater itself is thermodynamically tricky.
* Putting the NTC under a black bezel forces a larger heater and wastes energy.
📋 **Clip Abstract** Transparent heater designs for mining and an Airbus window show why temperature sensors must sit close to—but not on—the heater. Printed PTC fuses, black-bezel NTC placement, and the energy penalty of enlarging the heater frame the placement trade-off.
About the speaker:
* Speaker: Sebastian Gepp
* Company: Bopla Gehäuse Systeme GmbH
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#TransparentTemperatureSensors, #PrintedPTCTemperatureFuse, #BlackBezelNTC, #TransparentHeaterWindow, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
Transparent Temperature Sensors
More Highlights from the same talk.
05:12 - 06:18
How did consolidating a capacitive slider, display PCB and sealings into one hybrid film cut planned system cost by 12%?
How did consolidating a capacitive slider, display PCB and sealings into one hybrid film cut planned system cost by 12%?
The customer's starting box comprised an enclosure, customer PCBs, sealings, and a display mounted on a separate PCB, plus a requested small capacitive film for the slider. In the original build these were discrete items, so the architecture carried multiple boards and components rather than a single interface substrate.
Rather than accept that discrete build, the team combined the parts into one film. The hybrid film integrates the requested slider with the display PCB and sealing elements, cutting the number of PCBs and components. Capacitive keys are routed on the tail so the customer can access them directly through a bus system.
The consolidated approach saved about 12% of the customer's initial cost planning. That reduction was attributed to fewer PCBs and fewer components used in the build. The project thus turned a requested small capacitive slider film into a more integrated HMI assembly while preserving direct bus access to the capacitive keys.
In this short video, you can learn:
* A customer box originally used separate enclosure, PCBs, sealings, a display PCB, and a small capacitive slider film.
* Combining those parts into one hybrid film reduced PCB and component count while keeping capacitive keys directly accessible via a bus system on the tail.
* The integrated film cut about 12% from the customer's initial cost planning.
📋 **Clip Abstract** A customer HMI build with separate enclosure, PCBs, sealings, display PCB, and a requested capacitive slider film was consolidated into one hybrid film. The integration reduced PCB and component count, retained direct bus access to the capacitive keys on the tail, and saved about 12% versus the initial cost planning.
About the speaker:
* Speaker: Sebastian Gepp
* Company: Kundisch GmbH & Co. KG
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#CapacitiveSliderFilm, #HybridFilmIntegration, #DisplayPCBIntegration, #BusSystemTail, #PrintedElectronics, #HMI
10:16 - 11:40
What does a batteryless ePaper tag with 35 soldered components and an ERP-linked reader enable?
What does a batteryless ePaper tag with 35 soldered components and an ERP-linked reader enable?
The demonstrator is a very slim batteryless ePaper tag, currently PCB-based, with a flexible version under development. The complete system includes reader hardware and a software interface that hooks up to an ERP system. Based on an XML standard, images can be programmed depending on the ERP system.
Customers use the tags for routing job tickets: their paperwork moves onto ePaper, and after a job is done they create a new ePaper tag. A finished marketing example combines NFC reading technology and ePaper in one film. It simulates opening a box with a key, or uses a suitable RFID card placed on the setup, with the ePaper showing the actual status.
The 3D image shows the antenna and all needed components integrated into the setup. It has 35 components soldered directly on the film. The marketing implementation was done in German and English to target more customers at the moment. This illustrates a hybrid approach: film-integrated antenna and soldered components, NFC reading and an ePaper status display.
In this short video, you can learn:
* The tag is batteryless and currently PCB-based, with a flexible version in development.
* The reader and software interface connect to an ERP system, and XML standard programming sets images from ERP data.
* A marketing film combines NFC reading and ePaper, using a key simulation or RFID card to show actual status, with 35 components soldered directly on the film.
📋 **Clip Abstract** This clip presents a slim batteryless ePaper tag system, currently PCB-based with a flexible version in development, plus reader hardware and an ERP-linked software interface using XML standard programming. It shows job-ticket routing and a marketing film that combines NFC reading with ePaper, including a 3D setup with antenna and 35 components soldered directly on film.
About the speaker:
* Speaker: Sebastian Gepp
* Company: Kundisch GmbH & Co. KG
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#BatterylessEPaper, #NFCePaperFilm, #ERPLinkedTags, #FilmSolderedComponents, #PrintedHybridElectronics, #SmartLabels
07:28 - 08:40
Why did a 360-degree emergency signal light replace right-angle rigid PCBs with a flexible LED film?
Why did a 360-degree emergency signal light replace right-angle rigid PCBs with a flexible LED film?
Flexible LED films are integrated into membrane keyboards to deliver the homogeneous illumination customers expect as a quality baseline. The films are also supplied as standalone products: a serial RGB LED film runs at the back with programming on it, while just illumination films are also available.
In a customer project with Schranner, emergency signal lights previously used rigid PCBs to mount all LEDs and achieve 360-degree illumination. Those PCBs were mounted at an angle of 90 degrees, so the illumination was not really 360 degrees. Film technology replaced that arrangement in the new design.
With the film approach, the project saved direct producing cost or material cost and achieved true 360-degree illumination. Another product named is custom USB keyboards: users plug them in and they work, like familiar computer USB keyboards. The examples cover membrane-keyboard illumination, standalone LED films, emergency signal lights and custom input devices.
In this short video, you can learn:
* Flexible LED films deliver homogeneous illumination for membrane keyboards and can also be used as standalone RGB or illumination films.
* Schranner's emergency signal lights moved from rigid PCBs mounted at 90 degrees to film technology, achieving true 360-degree illumination.
* The film approach saved direct producing cost or material cost compared with the previous right-angle rigid-PCB assembly.
📋 **Clip Abstract** Flexible LED films are used for homogeneous membrane-keyboard illumination and as standalone serial RGB or illumination films. In Schranner emergency signal lights, film technology replaced right-angle rigid PCBs, saving direct producing or material cost and delivering true 360-degree illumination.
About the speaker:
* Speaker: Sebastian Gepp
* Company: Kundisch GmbH & Co. KG
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online
Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/
#FlexibleLEDFilm, #MembraneKeyboardIllumination, #RGBLEDFilm, #True360Illumination, #PrintedElectronics, #HybridElectronics
About this talk
→ Transparent Temperature Sensors · Sebastian Gepp · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Sebastian Gepp
- Applications using Printed and Hybrid Electronics in the HMI Industry · Printed, Hybrid, Structural, & 3D Electronics 2021
More highlights from Sebastian Gepp
- ▶ How did consolidating a capacitive slider, display PCB and sealings into one hybrid film cut planned system cost by 12%? · Printed, Hybrid, Structural & 3D Electronics 2021
- ▶ Why did a 360-degree emergency signal light replace right-angle rigid PCBs with a flexible LED film? · Printed, Hybrid, Structural & 3D Electronics 2021
- ▶ What does a batteryless ePaper tag with 35 soldered components and an ERP-linked reader enable? · Printed, Hybrid, Structural & 3D Electronics 2021


