top of page

Shizuo Tokito

Yamagata University

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Shizuo Tokito | Yamagata University: How can printing porous carbon-silicone sponges revolutionize robotic tactile sensitivity?

00:03:20 - 00:05:12

Other snippets from this talk

Summary of the clip:

How can printing porous carbon-silicone sponges revolutionize robotic tactile sensitivity?

The integration of tactile feedback in robotics requires highly compliant, responsive materials that mimic human skin. In this segment, the fabrication of a high-sensitivity tactile sensor array is detailed. By formulating a high-viscosity composite ink using carbon nanoparticles and polydimethylsiloxane (PDMS), a specialized porous sponge-like structure is printed over sintered silver electrodes on a flexible plastic substrate.

The resulting architecture features a 400-micrometer thick sensing layer with average pore sizes of 200 micrometers. This porous geometry is critical because it permits massive physical deformation under minute loads. The physical displacement of the porous network dramatically alters the electrical percolation pathways of the carbon nanoparticles, yielding a substantial change in resistance.

This manufacturing approach enables high-throughput printed electronics on flexible films. By combining low-temperature sintering of silver with elastomeric screen-printable inks, developers can easily pattern sensor arrays over large, non-planar surfaces. This offers a robust, cost-effective pathway to giving robotic effectors human-like pressure feedback.

In this short video, you can learn:
* How to formulate and screen-print a high-viscosity carbon nanoparticle and PDMS composite ink.
* The mechanical role of a 200-micrometer porous structure in achieving high sensitivity and large deformation.
* The deposition steps involving printed silver ink on flexible plastic films followed by sintering.

📋 **Clip Abstract** This video outlines the formulation and printing of a porous PDMS-carbon nanoparticle composite sensor on flexible plastic. It details how the sponge-like microstructure optimizes resistance changes under physical pressure to achieve exceptional tactile sensitivity.

🔗 Link in comments 👇

#CarbonPDMSComposite, #ScreenPrintedSensors, #PorousElastomer, #TactileSensorArray, #FlexibleElectronics, #ElectronicSkin

This is a highlight of the presentation:

​

Future of Electronics RESHAPED USA 2026

10-11 June 2026

Computer History Museum, Mountain View, California, USA

Organised By:

TechBlick

​

More Highlights from the same talk.

02:19 - 03:47

How does printing cut steps, material and energy versus photolithography in flexible hybrid electronics?

How does printing cut steps, material and energy versus photolithography in flexible hybrid electronics?

Photolithography is a multi-step sequence: coating, exposure, development and etching. Printing inverts that logic by putting the materials only where they are needed. For suitable devices, the printed route requires fewer steps and less material, and it may also reduce energy consumption, which is why printing is presented as a more sustainable, environmentally friendly manufacturing approach.

Flexible hybrid electronics combine printed electronics with conventional silicon electronics. Printing is used to make the interconnects, sensors and antennas; silicon chips and other standard module components are then added. The whole set of data and components is placed on a flexible substrate, as shown in the example on the left and the cross-sectional drawing below.

By combining printed interconnects, sensors and antennas with silicon chips and standard modules, the result is thin and flexible electronics. Sustainability is the stated entry point: being sustainable is the main reason the group works on flexible and printed electronics at all, with printing framed as the lower-step, lower-material, potentially lower-energy alternative to photolithography.

In this short video, you can learn:
* Photolithography requires coating, exposure, development and etching, whereas printing puts materials only where they are needed.
* For suitable devices, printing requires fewer steps and less material, and it may also reduce energy consumption.
* Flexible hybrid electronics combine printed interconnects, sensors and antennas with silicon chips and standard modules on a flexible substrate.

📋 **Clip Abstract** Printing puts materials only where they are needed, so suitable devices need fewer steps and less material than the coating, exposure, development and etching sequence of photolithography, with possible energy savings. Flexible hybrid electronics then add silicon chips and standard modules to printed interconnects, sensors and antennas on a flexible substrate, producing thin and flexible systems.

About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#PrintOnlyDeposition, #PhotolithographySteps, #SiliconChipIntegration, #FlexibleSubstrateStack, #FlexibleHybridElectronics, #PrintedElectronics

08:31 - 10:26

Can low-temperature solder and stacked silver pastes make printed circuits reliable despite 29x copper resistivity?

Can low-temperature solder and stacked silver pastes make printed circuits reliable despite 29x copper resistivity?

All layers are formed by screen printing with a curing step at 150 °C. A BLE module is attached to the printed circuit using low-temperature tin-bismuth solder that melts at about 140 °C. Reflow is then carried out at 170 °C for two minutes, only 30 °C above the solder's melting point, so the printed stack is never exposed to conventional reflow temperatures.

Three types of printed conductor were tested. Type A has good adhesion but is difficult to solder; Type B is very easy to solder but can peel off from the film. Stacking the A and B layers gave both good adhesion and good solderability in the test, turning a materials trade-off into a printable stack.

Two SpO2 device versions include the same small optical sensor, BLE module, other chips and battery. The first version did not work correctly. A printed circuit has about 29 times the resistivity of copper foil. The width and length of the interconnect were changed and the power supply layout improved, after which the second version worked well.

In this short video, you can learn:
* Stacking an adhesion-focused printed conductor under an easily solderable one delivered both properties in the same pad.
* Tin-bismuth solder melting near 140 °C permitted a 170 °C, two-minute reflow onto screen-printed layers cured at 150 °C.
* Compensating a printed resistivity roughly 29 times that of copper foil through interconnect geometry and power-supply layout turned a non-working SpO2 prototype into a working one.

📋 **Clip Abstract** Screen-printed circuits were assembled with tin-bismuth solder reflowed at 170 °C, and a stacked two-conductor pad resolved the adhesion-versus-solderability conflict. Correcting interconnect width and length plus power-supply layout for a printed resistivity 29 times that of copper foil made the second SpO2 prototype work.

About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#TinBismuthReflow, #StackedConductorPads, #ScreenPrintedInterconnects, #SpO2SensorModule, #FlexibleHybridElectronics, #PrintedElectronics

05:49 - 08:18

Why does PEN beat PET for solderable printed circuits, and how do two silver pastes trade adhesion for conductivity?

Why does PEN beat PET for solderable printed circuits, and how do two silver pastes trade adhesion for conductivity?

Both films were heated to 150 °C and compared. PEN showed very little shrinkage, less than 0.01%, while PET shrank much more, by about 0.4%. That dimensional stability is why PEN is used primarily — the film dimension must remain stable during processing, especially for solder bonding. PET is still usable with a support plate, or after heat treatment at over 150 °C.

Screen printing is a simple, well-known, established process. Two silver pastes from Fujipara Chemical, a Japanese material company, are used: Type A with larger silver particles and a polyurethane binder gives relatively low conductivity but strong adhesion to the substrate; Type B with silver nanoparticles gives high electrical conductivity. Type A is printed first, Type B on top, and the upper line is made slightly narrower to reduce paste beading — achieving good adhesion, high conductivity and cleaner line edges.

Four main process steps build the multi-layer circuit. First, the lower conductor is printed using the two silver pastes. Next, the insulating layer is printed twice. Then the upper conductor is printed again with the two silver pastes. Finally, the protective layer is printed. All four steps stay inside screen printing, the same simple, well-known and established process.

In this short video, you can learn:
* PEN shrank less than 0.01% at 150 °C against about 0.4% for PET, keeping film dimensions stable for solder bonding.
* Printing adhesive Type A first and conductive nanoparticle Type B on top delivers strong substrate adhesion together with high conductivity.
* Making the upper conductor line slightly narrower reduces paste beading and produces cleaner line edges.

📋 **Clip Abstract** PEN's sub-0.01% shrinkage at 150 °C, versus roughly 0.4% for PET, is why it is preferred where film dimensions must survive solder bonding. Two Fujipara Chemical silver pastes — adhesive Type A printed first, conductive nanoparticle Type B on top — are then combined in a four-step screen-printed multilayer stack with a twice-printed insulator and a protective layer.

About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#PENSubstrate, #SilverNanopaste, #ScreenPrintedConductors, #PasteBeadingControl, #FlexibleHybridElectronics, #PrintedElectronics


Other talks by Shizuo Tokito


More highlights from Shizuo Tokito

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page