Shizuo Tokito | Yamagata University: What sustainable materials and thin-chip packaging are needed before flexible hybrid electronics can scale?
13:16 - 15:38
Other snippets from this talk
Summary of the clip:
What sustainable materials and thin-chip packaging are needed before flexible hybrid electronics can scale?
The approach replaces conventional silver paste with silver-coated copper containing only 10% silver, lowering silver content while fabricating flexible hybrid electronic devices. Bio-based films serve as an alternative to conventional plastic films in a demonstrated pressure sensor array and a humidity sensor. The remaining questions are reproducibility, long-term durability and overall environmental impact, so the material case is not yet closed.
For packaging, the devices still use relatively thick and rigid module chips, and silicon pad pitch is much finer than printed interconnect pitch. Thin chip foil packages address this mismatch: their fanned-out interconnects connect thin chip packets to wider printed interconnects. The stated aim is improved flexibility and reliability of flexible hybrid electronic devices, the main goal of a new three-year ICON project with Fraunhofer EMFT and Fraunhofer IZFP in Germany.
The roadmap follows demonstrated flexible sensor systems. The next step is to use a thin chip package and better material. The joint project started this year and runs for three years, linking material substitution with packaging work. Both sit on that next-step agenda: bio-based films and lower-silver paste for materials, and thin chip foil packages with fanned-out interconnects for packaging.
In this short video, you can learn:
* Silver-coated copper with only 10% silver cuts silver content versus conventional silver paste in fabricated FHG devices.
* Bio-based films were demonstrated in a pressure sensor array and a humidity sensor as alternatives to conventional plastic films.
* Thin chip foil packages use fanned-out interconnects to bridge fine silicon pad pitch and wider printed interconnects, targeting flexibility and reliability.
π **Clip Abstract** The clip presents silver-coated copper paste with 10% silver and bio-based films for flexible hybrid electronic devices, including a pressure sensor array and humidity sensor. It then describes thin chip foil packages with fanned-out interconnects and a three-year ICON project with Fraunhofer EMFT and Fraunhofer IZFP to improve flexibility and reliability.
About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#SilverCoatedCopper, #BioBasedFilm, #ThinChipFoil, #FannedOutInterconnects, #FlexibleHybridElectronics, #PrintedElectronics
This is a highlight of the presentation:
Scalable and Sustainable Flexible Hybrid Electronics for Smart Sensor Systems
More Highlights from the same talk.
02:19 - 03:47
How does printing cut steps, material and energy versus photolithography in flexible hybrid electronics?
How does printing cut steps, material and energy versus photolithography in flexible hybrid electronics?
Photolithography is a multi-step sequence: coating, exposure, development and etching. Printing inverts that logic by putting the materials only where they are needed. For suitable devices, the printed route requires fewer steps and less material, and it may also reduce energy consumption, which is why printing is presented as a more sustainable, environmentally friendly manufacturing approach.
Flexible hybrid electronics combine printed electronics with conventional silicon electronics. Printing is used to make the interconnects, sensors and antennas; silicon chips and other standard module components are then added. The whole set of data and components is placed on a flexible substrate, as shown in the example on the left and the cross-sectional drawing below.
By combining printed interconnects, sensors and antennas with silicon chips and standard modules, the result is thin and flexible electronics. Sustainability is the stated entry point: being sustainable is the main reason the group works on flexible and printed electronics at all, with printing framed as the lower-step, lower-material, potentially lower-energy alternative to photolithography.
In this short video, you can learn:
* Photolithography requires coating, exposure, development and etching, whereas printing puts materials only where they are needed.
* For suitable devices, printing requires fewer steps and less material, and it may also reduce energy consumption.
* Flexible hybrid electronics combine printed interconnects, sensors and antennas with silicon chips and standard modules on a flexible substrate.
π **Clip Abstract** Printing puts materials only where they are needed, so suitable devices need fewer steps and less material than the coating, exposure, development and etching sequence of photolithography, with possible energy savings. Flexible hybrid electronics then add silicon chips and standard modules to printed interconnects, sensors and antennas on a flexible substrate, producing thin and flexible systems.
About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#PrintOnlyDeposition, #PhotolithographySteps, #SiliconChipIntegration, #FlexibleSubstrateStack, #FlexibleHybridElectronics, #PrintedElectronics
08:31 - 10:26
Can low-temperature solder and stacked silver pastes make printed circuits reliable despite 29x copper resistivity?
Can low-temperature solder and stacked silver pastes make printed circuits reliable despite 29x copper resistivity?
All layers are formed by screen printing with a curing step at 150 Β°C. A BLE module is attached to the printed circuit using low-temperature tin-bismuth solder that melts at about 140 Β°C. Reflow is then carried out at 170 Β°C for two minutes, only 30 Β°C above the solder's melting point, so the printed stack is never exposed to conventional reflow temperatures.
Three types of printed conductor were tested. Type A has good adhesion but is difficult to solder; Type B is very easy to solder but can peel off from the film. Stacking the A and B layers gave both good adhesion and good solderability in the test, turning a materials trade-off into a printable stack.
Two SpO2 device versions include the same small optical sensor, BLE module, other chips and battery. The first version did not work correctly. A printed circuit has about 29 times the resistivity of copper foil. The width and length of the interconnect were changed and the power supply layout improved, after which the second version worked well.
In this short video, you can learn:
* Stacking an adhesion-focused printed conductor under an easily solderable one delivered both properties in the same pad.
* Tin-bismuth solder melting near 140 Β°C permitted a 170 Β°C, two-minute reflow onto screen-printed layers cured at 150 Β°C.
* Compensating a printed resistivity roughly 29 times that of copper foil through interconnect geometry and power-supply layout turned a non-working SpO2 prototype into a working one.
π **Clip Abstract** Screen-printed circuits were assembled with tin-bismuth solder reflowed at 170 Β°C, and a stacked two-conductor pad resolved the adhesion-versus-solderability conflict. Correcting interconnect width and length plus power-supply layout for a printed resistivity 29 times that of copper foil made the second SpO2 prototype work.
About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#TinBismuthReflow, #StackedConductorPads, #ScreenPrintedInterconnects, #SpO2SensorModule, #FlexibleHybridElectronics, #PrintedElectronics
05:49 - 08:18
Why does PEN beat PET for solderable printed circuits, and how do two silver pastes trade adhesion for conductivity?
Why does PEN beat PET for solderable printed circuits, and how do two silver pastes trade adhesion for conductivity?
Both films were heated to 150 Β°C and compared. PEN showed very little shrinkage, less than 0.01%, while PET shrank much more, by about 0.4%. That dimensional stability is why PEN is used primarily β the film dimension must remain stable during processing, especially for solder bonding. PET is still usable with a support plate, or after heat treatment at over 150 Β°C.
Screen printing is a simple, well-known, established process. Two silver pastes from Fujipara Chemical, a Japanese material company, are used: Type A with larger silver particles and a polyurethane binder gives relatively low conductivity but strong adhesion to the substrate; Type B with silver nanoparticles gives high electrical conductivity. Type A is printed first, Type B on top, and the upper line is made slightly narrower to reduce paste beading β achieving good adhesion, high conductivity and cleaner line edges.
Four main process steps build the multi-layer circuit. First, the lower conductor is printed using the two silver pastes. Next, the insulating layer is printed twice. Then the upper conductor is printed again with the two silver pastes. Finally, the protective layer is printed. All four steps stay inside screen printing, the same simple, well-known and established process.
In this short video, you can learn:
* PEN shrank less than 0.01% at 150 Β°C against about 0.4% for PET, keeping film dimensions stable for solder bonding.
* Printing adhesive Type A first and conductive nanoparticle Type B on top delivers strong substrate adhesion together with high conductivity.
* Making the upper conductor line slightly narrower reduces paste beading and produces cleaner line edges.
π **Clip Abstract** PEN's sub-0.01% shrinkage at 150 Β°C, versus roughly 0.4% for PET, is why it is preferred where film dimensions must survive solder bonding. Two Fujipara Chemical silver pastes β adhesive Type A printed first, conductive nanoparticle Type B on top β are then combined in a four-step screen-printed multilayer stack with a twice-printed insulator and a protective layer.
About the speaker:
* Speaker: Shizuo Tokito
* Company: Yamagata University
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
π
Save the date: 20 and 21 October 2027
π Berlin, Germany
π Info: https://www.techblick.com/sustainableelectronicsreshaped
#PENSubstrate, #SilverNanopaste, #ScreenPrintedConductors, #PasteBeadingControl, #FlexibleHybridElectronics, #PrintedElectronics
About this talk
β Scalable and Sustainable Flexible Hybrid Electronics for Smart Sensor Systems Β· Shizuo Tokito Β· Sustainable Electronics RESHAPED 2026 Berlin
Other talks by Shizuo Tokito
- Flexible Printed Sensors for Robotic Hands: Toward Human-Like Tactile Sensing Β· Wearables RESHAPED USA 2026
- Flexible Printed Carbon-based Sensors and Their Applications Β· The Future of Electronics RESHAPED | Berlin 2023
More highlights from Shizuo Tokito
- βΆ How can printing porous carbon-silicone sponges revolutionize robotic tactile sensitivity? Β· Future of Electronics RESHAPED USA 2026
- βΆ Can a robot distinguish material softness using spatial-temporal resistance patterns? Β· Future of Electronics RESHAPED USA 2026
- βΆ Are thermal noise and PFAS regulations the ultimate hurdles for printed robotic skin? Β· Future of Electronics RESHAPED USA 2026
- βΆ Can deep eutectic solvents revolutionize the fabrication of low-cost, highly porous piezoresistive sensors? Β· The Future of Electronics RESHAPED 2023 Berlin
- βΆ How can an artificial finger distinguish material softness using flexible sensor arrays? Β· The Future of Electronics RESHAPED 2023 Berlin
- βΆ Can combining cellulose nanofibers with carbon black yield ultra-fast printed humidity sensors? Β· The Future of Electronics RESHAPED 2023 Berlin


