top of page

Simon Rihm

Notion Systems

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Simon Rihm | Notion Systems: What makes piezo inkjet fast and precise enough for functional electronics?

10:14 - 11:59

Other snippets from this talk

Summary of the clip:

What makes piezo inkjet fast and precise enough for functional electronics?

Inkjet is a non-contact digital printing method. It can create fine structures of 30 microns or more, though going below that is difficult and depends on substrate and ink. Droplets are ejected by a piezo element in the printhead chamber, with an adjusted electric pulseโ€”the waveform or fire pulseโ€”deflecting a membrane.

That pulse deflection generates an acoustic wave inside the chamber, pushing the droplet out. The key advantage is speed: up to 100,000 droplets per second per nozzle, and highly parallel operation with typically more than 10,000 nozzles per print unit. It is touchless, so there is no contact between printhead and substrate.

Because inkjet is fully digital and maskless, it enables wet-on-wet processing without masks or screens, and it gives control and a decision at every point: where to print and when to print. The achievable resolution is constrained by substrate and ink, with 30 microns presented as the practical fine-structure target.

In this short video, you can learn:
* Inkjet is non-contact and digital, allowing maskless, screenless deposition.
* Piezo waveform deflection creates an acoustic wave that ejects droplets at up to 100,000 droplets per second per nozzle.
* Practical fine structures start at about 30 microns, with substrate and ink limiting further resolution.

๐Ÿ“‹ **Clip Abstract** Piezo inkjet uses an electric waveform to deflect a membrane, generating an acoustic wave that ejects droplets. It offers non-contact, fully digital patterning with up to 100,000 droplets per second per nozzle, over 10,000 nozzles per print unit, and fine structures of 30 microns or more.

About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
๐Ÿ“… Save the date: 9 and 10 June 2027
๐Ÿ“ Mountain View, California (Silicon Valley)
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
๐Ÿ“… Save the date: 20 and 21 October 2027
๐Ÿ“ Berlin, Germany
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshaped

#PiezoInkjet, #FirePulse, #WetOnWet, #FunctionalInkjet, #PrintedElectronics, #AdditiveManufacturing

This is a highlight of the presentation:

Enabling Sustainable Electronics Manufacturing through Additive Functional Inkjet Printing

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

02:33 - 04:33

Printing the functional layer directly eliminates how many of the six standard subtractive process steps?

Printing the functional layer directly eliminates how many of the six standard subtractive process steps?

The conventional subtractive route starts with a substrate and applies the functional layer across the entire surface. It then adds resist, exposes the resist, develops it, etches the functional layer, and finally strips the resist. In this example, creating just one needed functional layer consumes six production steps, driving a fairly high investment in time and resources.

Introducing additive manufacturing changes that sequence for two applications. In the top process, the goal is to print or create the etch resist layer directly. Printing that etch resist directly avoids two process steps. In the bottom process, the goal is to print the functional layer itself, which skips five prior steps and leaves only one production step.

The comparison is simple: direct printing of the functional layer reduces the six-step subtractive example to a single production step. Direct printing of the etch resist removes two steps instead. This illustrates how additive methods reduce production steps and, by extension, the time and resource investment required to create needed functional layers.

In this short video, you can learn:
* A conventional subtractive flow for one functional layer uses six steps: functional layer, resist apply, expose, develop, etch, strip.
* Printing the etch resist directly avoids two of those process steps.
* Printing the functional layer itself skips five prior steps, leaving only one production step.

๐Ÿ“‹ **Clip Abstract** The clip contrasts a six-step subtractive process for creating one functional layer with additive alternatives. Printing the etch resist directly removes two steps, while printing the functional layer itself skips five prior steps and reduces production to a single step.

About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#EtchResistPrinting, #FunctionalLayerPrinting, #SubtractiveEtch, #ProcessStepReduction, #PrintedElectronics, #AdditiveElectronics

03:40 - 05:23

How many process steps can additive inkjet eliminate from one functional layer?

How many process steps can additive inkjet eliminate from one functional layer?

In the subtractive baseline, producing one functional layer takes six steps: apply the functional layer, apply resist, expose resist, develop resist, etch the layer, and strip the resist. The substrate is the starting point. That sequence is described as a lot of steps and motivates comparing it with additive manufacturing.

Moving from subtractive to additive can remove the subtractive process; in the example, the route goes to step four. Going further, the functional layer itself can be printed directly as the sixth step. Additive manufacturing produces that layer in one single producing step instead.

The stated advantage is reduced process steps. Because of that reduction, faster turnaround is also cited as a consequence. The concrete comparison in the clip is one single functional layer, where direct additive printing replaces the multi-step subtractive sequence.

In this short video, you can learn:
* The subtractive example uses six producing steps to create one functional layer.
* Additive manufacturing can print the functional layer directly in one single producing step.
* Reduced process steps are cited as an advantage that also enables faster turnaround.

๐Ÿ“‹ **Clip Abstract** A subtractive flow for one functional layer is broken down into six producing steps, from functional-layer application through resist processing and etch to resist strip. Direct additive printing is contrasted as a one-step route to the functional layer, with reduced process steps linked to faster turnaround.

About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
๐Ÿ“… Save the date: 9 and 10 June 2027
๐Ÿ“ Mountain View, California (Silicon Valley)
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
๐Ÿ“… Save the date: 20 and 21 October 2027
๐Ÿ“ Berlin, Germany
๐Ÿ“‹ Info: https://www.techblick.com/electronicsreshaped

#SubtractiveProcess, #AdditiveManufacturing, #FunctionalLayer, #ReducedProcessSteps, #PrintedElectronics, #InkjetPrinting

05:20 - 07:00

Can inkjet match subtractive-method throughput, and at what droplet rate per nozzle?

Can inkjet match subtractive-method throughput, and at what droplet rate per nozzle?

At the core of these systems is inkjet: ejecting super-small droplets of fluid from a jetting nozzle, measured in picoliters. The claimed speed is up to 100,000 droplets per second per nozzle, which reframes productivity not as a single-nozzle limit but as a rate multiplied across the head.

The second lever is parallelism: printing is not done with a single nozzle but with around 10,000 per print unit. That combination โ€” 100,000 droplets per second per nozzle across roughly 10,000 nozzles โ€” is the throughput argument for matching subtractive production methods.

Two further properties separate it from subtractive flows. Inkjet is touchless: the printing unit and the substrate never come into contact during the whole printing process. And it is digital, so at any time you decide when, where and whether a drop is generated. That is the material-efficiency and reconfiguration case.

In this short video, you can learn:
* Inkjet ejects picoliter droplets, with up to 100,000 droplets per second generated per single nozzle.
* Throughput scales through parallelism: around 10,000 nozzles are used per print unit rather than a single jet.
* Because the process is touchless and digital, drop placement is decided at any time, in any position, or not at all.

๐Ÿ“‹ **Clip Abstract** Inkjet productivity rests on three properties: picoliter droplets fired at up to 100,000 per second per nozzle, around 10,000 nozzles per print unit for parallelism, and a touchless, digital process. Digital control means the drop is generated โ€” or withheld โ€” at any time and position, which is the basis for comparing additive output against subtractive production.

About the speaker:
* Speaker: Simon Rihm
* Company: Notion Systems
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform

Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/

#InkjetPrinting, #PicoliterDroplets, #PrintheadNozzles, #TouchlessDeposition, #AdditiveElectronics, #PrintedElectronics


About this talk

โ†’ Enabling Sustainable Electronics Manufacturing through Additive Functional Inkjet Printing ยท Simon Rihm ยท The Future of Electronics RESHAPED 2026 Berlin


Other talks by Simon Rihm


More highlights from Simon Rihm

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page