top of page

Thibaut Soulestin

Henkel

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Thibaut Soulestin | Henkel: How do advancements in ink formulation enable higher printing speeds in flexographic and gravure printing processes for printed electronics?

00:13:01 - 00:13:33

Other snippets from this talk

Summary of the clip:

How do advancements in ink formulation enable higher printing speeds in flexographic and gravure printing processes for printed electronics?

The speaker shifts the focus from material composition to process optimization, specifically addressing how ink formulations are being developed to enable higher printing speeds. The goal is to improve the cost-effectiveness of printed electronics by increasing throughput. Flexographic and gravure printing are presented as methods capable of achieving significantly higher speeds compared to traditional screen printing.

Achieving high printing speeds requires inks with specific properties that allow for the deposition of thin layers while maintaining excellent electrical conductivity. The ink formulation must be optimized to ensure proper wetting, adhesion, and drying characteristics at these elevated speeds. This often involves careful selection of solvents, binders, and additives to control the ink's rheology and surface tension.

The speaker notes that printing at higher speeds necessitates the deposition of much thinner layers of ink. Therefore, the ink must be formulated to achieve the desired electrical conductivity even at reduced thicknesses. This requires a balance between the concentration of conductive particles, their dispersion within the ink matrix, and their ability to form a continuous conductive network after printing and drying.

In this short video, you can learn:

* The shift towards flexographic and gravure printing to increase printing speeds.
* The importance of ink formulation for achieving high-speed printing of thin layers.
* The need for excellent electrical conductivity even with reduced ink thickness.

đź“‹ **Clip Abstract:** This segment discusses the use of flexographic and gravure printing to improve the cost-effectiveness of printed electronics by increasing printing speeds. It highlights the importance of ink formulation for achieving high conductivity in thin layers.
🔗 Link in comments 👇

#InkFormulation, #FlexoGravurePrinting, #HighSpeedPrinting, #ThinFilmConductivity, #PrintedElectronics, #AdvancedManufacturing

This is a highlight of the presentation:

High Performance Inks for Cost Efficient Manufacturing of Printed Electronics

The Future of Electronics RESHAPED 2025

​

22-23 October 2025

Estrel Congress Centre, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

04:12 - 05:28

An ink is an enabler, not a product — so how does a large materials player choose among three development routes?

An ink is an enabler, not a product — so how does a large materials player choose among three development routes?

The preferred route is customer-specific development: a customer arrives with known requirements and volume, and the materials supplier works to that brief. But this route is not frequent, especially for an ink player, because the ink enables the innovation rather than standing alone as the product.

Stretchable ink illustrates the value-chain position. A stretchable ink enables stretchable electronics, which then enable the final application, so the ink supplier enters very early. That early position still requires delivering good product quality so customers can develop good printing devices.

The second route is market-driven: identify a market trend and develop a product for that market. The third route targets new technologies, such as silver-plated copper inks, where an in-house supplier is developing new flakes. These routes sit alongside the customer-specific preference and the early value-chain role of the ink.

In this short video, you can learn:
* Customer-specific ink development starts from known requirements and volume but is not the most frequent route because inks enable downstream innovation.
* Stretchable inks must be available early in the value chain and delivered at good quality so customers can build printing devices.
* Market-driven projects follow identified trends, while new-technology projects pursue materials such as silver-plated copper inks with new flakes from an in-house supplier.

đź“‹ **Clip Abstract** The clip contrasts three development routes for a large ink supplier: customer-specific work, market-driven projects and new-technology programs. It uses stretchable inks and silver-plated copper inks to show why an enabler material must enter early in the value chain while still meeting product-quality requirements.

About the speaker:
* Speaker: Thibaut Soulestin
* Company: Henkel
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
đź“… Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
đź“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
đź“… Save the date: 20 and 21 October 2027
📍 Berlin, Germany
đź“‹ Info: https://www.techblick.com/electronicsreshaped

#CustomerSpecificInk, #StretchableInk, #SilverPlatedCopperInks, #CopperFlakes, #PrintedElectronics, #AdditiveElectronics

09:09 - 10:50

Why is printed silver the answer to antenna interference — and what ink survives radar-absorbing defence hardware?

Why is printed silver the answer to antenna interference — and what ink survives radar-absorbing defence hardware?

Connectivity growth is driven by the internet giants, and the West Coast R&D centre sits next to them. For those customers the workhorse is highly conductive silver ink, particularly for phase array antennas: low earth orbit links between ground stations and internet satellites. That is where specific inks were developed.

As more antennas radiate at different frequencies, interference grows, so frequency selective surfaces act as filters. Printed electronics suits this because the filter can be printed on the housing itself, in flexible shapes over large surfaces, and cheaply — only a very small quantity of silver is deposited.

Radar-absorbing materials, largely a defence market, need a different chemistry: carbon inks with very high thermal stability. The answer is polyimide-based ink, polyimide being the most thermostable class of polymer. This work is mostly driven from the US, but the transfer to other regions is visible, especially from North America to Europe.

In this short video, you can learn:
* Highly conductive silver inks are tailored for phase array antennas serving low earth orbit ground-to-satellite internet links.
* Frequency selective surfaces are printed directly on housings because printing large, flexible shapes consumes only a very small quantity of silver.
* Radar-absorbing defence hardware relies on carbon inks built on polyimide, the most thermostable polymer, and that product line is now transferring from North America to Europe.

đź“‹ **Clip Abstract** Printed silver delivers highly conductive phase array antennas for low earth orbit links and printed frequency selective filters that suppress interference between antennas radiating at different frequencies. Defence radar-absorbing hardware instead needs carbon inks on a polyimide base for very high thermal stability, a product largely driven from the US and now transferring to Europe.

About the speaker:
* Speaker: Thibaut Soulestin
* Company: Henkel
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
đź“… Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
đź“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
đź“… Save the date: 20 and 21 October 2027
📍 Berlin, Germany
đź“‹ Info: https://www.techblick.com/electronicsreshaped

#SilverInk, #FrequencySelectiveSurface, #PhaseArrayAntenna, #PolyimideInk, #PrintedElectronics, #AdditiveElectronics

07:10 - 09:13

What inks do humanoid robot fingertips need, and why is all of that R&D being done in Shanghai?

What inks do humanoid robot fingertips need, and why is all of that R&D being done in Shanghai?

Humanoid hands impose very specific sensing requirements at the fingertips, where printed electronics can bring several solutions: capacitive touch sensors, force-sensitive resistors, more traditional force sensors, plus strain, bending and elongation sensors. All of these can be combined together in one hand to bring the best possible robotic hands, which means several different inks must coexist in the same build.

In all three applications shown, specific carbon inks are used, and that is where materials development expertise comes into play. Force-sensitive resistor ink requirements are extremely different from the strain ink and from the bending ink, so the formulation you put up and the processing know-how you need to bring differ from one to the next to make each a success.

That development is not happening in Europe, which is why it happens in China, with a local R&D team close to the customer. All electronics and robotics developments are run from the R&D center in Shanghai, and the resulting ink developments transfer to other regions, where the applications differ but the learnings still benefit everyone, including sensitive industrial robots.

In this short video, you can learn:
* Fingertip sensing for humanoid hands can combine capacitive touch, force-sensitive resistors, traditional force sensors and strain, bending and elongation sensors in one printed stack.
* Force-sensitive resistor, strain and bending inks each demand a different formulation and different processing know-how, all built on specific carbon ink chemistries.
* Because this development sits in Shanghai close to the customer rather than in Europe, ink learnings transfer quickly to other regions and other robot types such as highly sensitive industrial robots.

đź“‹ **Clip Abstract** Printed sensors for humanoid fingertips combine capacitive touch, force-sensitive resistors, strain, bending and elongation sensing, each requiring a distinctly formulated carbon ink and its own processing know-how. That development is concentrated in Shanghai close to the customer, with the resulting inks transferred to other regions for industrial robots and other applications.

About the speaker:
* Speaker: Thibaut Soulestin
* Company: Henkel
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
đź“… Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
đź“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
đź“… Save the date: 20 and 21 October 2027
📍 Berlin, Germany
đź“‹ Info: https://www.techblick.com/electronicsreshaped

#FSRInk, #CarbonInkFormulation, #FingertipSensors, #StrainSensingInk, #PrintedElectronics, #HumanoidRobotics


About this talk

→ High Performance Inks for Cost Efficient Manufacturing of Printed Electronics · Thibaut Soulestin · The Future of Electronics RESHAPED 2025


Other talks by Thibaut Soulestin


More highlights from Thibaut Soulestin

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page