Andrew Strudwick | GEIC: Why can’t graphene conductive inks match silver inks, and where do they still win?
14:33 - 15:40
Other snippets from this talk
Summary of the clip:
Why can’t graphene conductive inks match silver inks, and where do they still win?
The answer given is physics: graphene conductive inks have not been seen as comparable to silver inks. Conductivity is limited by how much conductance the platelets can deliver, and by binders and other components in the ink. For ultimate conductivity, you will struggle to beat the metals.
The win is not metal-level conductivity. In the inBrain example, the material is carbon based, which the speaker links to better compatibility in bio applications. There, the relevant criterion is application compatibility rather than matching silver's conductivity.
For flexible systems, the clip turns to graphene, but cuts off at 'graphene then'. The contrast remains: silver is the conductivity benchmark, while graphene's case is argued through bio compatibility and flexible-system relevance, not through comparable conductive-ink performance.
In this short video, you can learn:
* Graphene conductive inks have not been seen as comparable to silver inks.
* Platelet conductivity limits and binder presence cap ink performance, while metals remain hard to beat on ultimate conductivity.
* Carbon-based inBrain materials are cited for better bio compatibility, and graphene is raised for flexible systems.
📋 **Clip Abstract** The clip explains why graphene conductive inks still trail silver: platelet conductivity limits and binders cap performance, while metals remain the ultimate conductivity benchmark. It then identifies application-led wins, citing carbon-based inBrain compatibility for bio uses and graphene's relevance for flexible systems.
About the speaker:
* Speaker: Andrew Strudwick
* Company: GEIC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#GrapheneConductiveInks, #SilverInkBenchmark, #PlateletConductivity, #CarbonBasedInks, #PrintedElectronics, #FlexibleElectronics
This is a highlight of the presentation:
Graphene at Twenty: From Scientific Discovery to Commercial Reality
More Highlights from the same talk.
05:55 - 08:14
How can screen printing and small-scale pre-tests de-risk a new formulation before full roll-to-roll production?
How can screen printing and small-scale pre-tests de-risk a new formulation before full roll-to-roll production?
The workhorse system is a Microtech screen printer, used for rapid prototyping. Hundreds of test devices can be printed within half a day, then statistical data generated on those devices. Application areas include biosensors, heating elements and mechanical sensors; some details are withheld for client confidentiality, with case studies later.
Substrate work spans fabrics, polymers and bits for carbon-fibre composites, with many different substrate types. Alongside the screen printer is roll-to-roll capability using a Coatma base coater. That system offers many print methods, allowing pre-tests on smaller scale.
The aim is to de-risk activity for partners before they take a process, new formulation or new substrate to a full production house. Pre-tests provide parameters that have worked at smaller scale before full roll-to-roll. This reduces cost risk from taking down a production site and starting from scratch. In-house measurement capability and expertise exist.
In this short video, you can learn:
* A Microtech screen printer supports rapid prototyping, printing hundreds of test devices in half a day for statistical data.
* Roll-to-roll work uses a Coatma base coater with many print methods, enabling smaller-scale parameter pre-tests.
* Substrate range includes fabrics, polymers and bits for carbon-fibre composites, with in-house measurement capability and expertise.
📋 **Clip Abstract** Screen printing and roll-to-roll pre-tests de-risk new formulations, processes and substrates before full production, reducing cost risk. The setup covers fabrics, polymers, carbon-fibre composite inserts, biosensors, heating elements and mechanical sensors.
About the speaker:
* Speaker: Andrew Strudwick
* Company: University of Manchester
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#MicrotechScreenPrinter, #CoatmaBaseCoater, #CarbonFibreCompositeSubstrates, #RollToRollPreTests, #PrintedElectronics, #2DMaterials
01:55 - 03:36
Why did sticky-tape exfoliation of micron-scale flakes create graphene hype before scalable supply?
Why did sticky-tape exfoliation of micron-scale flakes create graphene hype before scalable supply?
Isolation was deliberately simple: a sellotape-like tape peeled graphite layers apart until a monolayer remained. The Nobel Prize recognised the quantum Hall effect measured on those flakes through good microfab, but the appeal was the method itself. That simplicity captured the scientific community’s attention and set up the hype cycle that followed.
Once people measured the physical properties, superlative values appeared for mechanical strength, electrical, thermal and chemical performance, plus area performance. The catch: most results came from micron-scale single flakes isolated by the sellotape method, not a scalable supply route. Hype ran ahead of manufacturability.
One year after the original graphene paper, a paper showed graphite was not alone: other layered 3D materials could be exfoliated into 2D by the same method, creating a material portfolio. Boron nitride is a dielectric insulator that conducts thermally; other 2D materials such as MoS2 are semiconductors.
In this short video, you can learn:
* The original isolation used a sellotape-like tape to peel graphite down to monolayer flakes, and the Nobel Prize was for quantum Hall measurements made on those flakes.
* Superlative mechanical, electrical, thermal and chemical values were measured on micron-scale single flakes, which was not scalable.
* A year after the first graphene paper, other layered 3D materials—boron nitride and MoS2 among them—were exfoliated into 2D, expanding the portfolio.
📋 **Clip Abstract** The clip traces graphene’s sticky-tape isolation to monolayer flakes and the quantum Hall microfab that won the Nobel Prize, explaining how simplicity drove hype. It contrasts superlative properties measured on micron-scale flakes with the absence of scalable supply, then notes the one-year-later expansion to boron nitride and MoS2.
About the speaker:
* Speaker: Andrew Strudwick
* Company: GEIC
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
USA: The Future of Electronics RESHAPED | USA
📅 Save the date: 9 and 10 June 2027
📍 Mountain View, California (Silicon Valley)
📋 Info: https://www.techblick.com/electronicsreshapedusa
Europe
The Future of Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/electronicsreshaped
#StickyTapeExfoliation, #MicronScaleFlakes, #QuantumHallEffect, #BoronNitrideDielectric, #2DMaterials, #GrapheneCommercialisation
15:30 - 16:57
Who owns the IP when a company develops a graphene product with the center?
Who owns the IP when a company develops a graphene product with the center?
The center exists to stimulate commercialization, so it gives IP to the end user—the company. A royalty fee is included; it can be negotiated and is project dependent. The center does not hold onto the IP, letting it go into the company. The company is free to take it forward.
The royalty is charged on the graphene-containing element within that product. For example, if a heating element sits within a phone, the royalty would not be on the phone; it would be on the heating element. The same applies to a thermal dissipation element.
Asked whether the model is license, hold, or assign, the answer is that it's theirs. The company receives the IP, and the center charges a royalty. The clip closes by asking how a startup company from India could approach the center for research work.
In this short video, you can learn:
* The center assigns resulting IP to the end user, the company, with a royalty fee that is negotiable and project dependent.
* Royalties attach to the graphene-containing element, such as a phone's heating or thermal dissipation element, not the entire phone.
* The IP model is described as the company's—'it's theirs'—so licenses or retention by the center are not the mechanism.
📋 **Clip Abstract** The clip addresses IP ownership when a company develops a graphene product with the center. The center gives IP to the end-user company, charges a negotiable royalty on the graphene-containing element, and does not hold the IP, leaving the company free to take it forward.
About the speaker:
* Speaker: Andrew Strudwick
* Company: University of Manchester
* Event: nnovation Festival: Additive, Printed, Sustainable Electronics, MicroLEDs and AR/VR Displays, Perovskites | July 2026
* Location: Online Platform
Annual access to our onsite event(s), all online events and a library featuring over 1800 presentations (recordings + PDF) across all our onsite and onsite events and technology areas. Join us and over 2000 members from around the world now.
Explore and join now --> https://www.techblick.com/
#GrapheneIP, #RoyaltyModel, #ThermalDissipationElement, #HeatingElement, #2DMaterials, #GrapheneElectronics
About this talk
→ Graphene at Twenty: From Scientific Discovery to Commercial Reality · Andrew Strudwick · The Future of Electronics RESHAPED 2026 Berlin
Other talks by Andrew Strudwick
- Graphene and 2D materials printed electronics · TechBlick Innovations Festival July 2026
- 2D materials in printed electronics · Electronics RESHAPED USA 2026
- Graphene and 2D Material Inks: Conductive, Optical and Beyond · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
More highlights from Andrew Strudwick
- ▶ How can screen printing and small-scale pre-tests de-risk a new formulation before full roll-to-roll production? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Who owns the IP when a company develops a graphene product with the center? · Innovation Festival: Additive, Printed, Sustainable Electronics
- ▶ Can we de-risk the transition of novel 2D formulations to high-throughput roll-to-roll manufacturing without risking production line downtime? · Future of Electronics RESHAPED USA 2026
- ▶ How do you transition delicate benchtop 2D-material characterization into inline quality control for high-speed manufacturing? · Future of Electronics RESHAPED USA 2026
- ▶ Why does graphene outperform other carbon-based additives in flexible printed electronics and composite materials? · Future of Electronics RESHAPED USA 2026
- ▶ How can you accelerate advanced materials R&D from a 3-year cycle to just 3 months? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- ▶ Can a traditional technique like screen printing be the key to prototyping next-gen graphene sensors? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025
- ▶ What does it take to move printed graphene devices from the lab bench to pilot-scale production? · Additive, Printed, Hybrid and Sustainable Electronics Innovations Day 2025


