top of page

Christoph Bosshard

Kimoto

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Christoph Bosshard | Kimoto: How do UV-deactivation and polyimide carriers survive dicing forces and high-temperature processing?

09:20 - 10:42

Other snippets from this talk

Summary of the clip:

How do UV-deactivation and polyimide carriers survive dicing forces and high-temperature processing?

For dicing, the protection film is applied with a strong adhesive force before mechanical processing. That adhesion keeps parts from lying around and becoming defects when dicing forces are applied. After processing, UV light deactivates the adhesive layer, so the part can be moved to the next process.

For very high-temperature processes, a different base film is used: polyimide with a specially formulated adhesive. Even after high-temperature influence, the adhesive will not start to degrade, so it can still be removed properly without residue after the temperature process. Typical applications include solar reflow manufacturing, battery applications, electric motors and thin metal foil processing.

These two cases show that the protection film can be tailored to specific application cases. One formulation prioritises strong adhesion for dicing, then UV deactivation for release. The other prioritises polyimide and an adhesive that survives high temperature and remains removable without residue.

In this short video, you can learn:
* Strong dicing adhesion prevents parts from lying around and causing defects under mechanical force.
* UV light deactivates the adhesive layer after processing so the part can move to the next process.
* A polyimide base film with a specially formulated adhesive resists high-temperature degradation and is removed without residue.

πŸ“‹ **Clip Abstract** The clip contrasts two carrier-film approaches: a strong-adhesion film for dicing that is released by UV deactivation, and a polyimide-based film for very high-temperature processes. It also lists solar reflow, battery, electric-motor and thin-metal-foil applications where the protection film is tailored to the process.

About the speaker:
* Speaker: Christoph Bosshard
* Company: Kimoto
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#UVDeactivation, #PolyimideCarrier, #DicingAdhesion, #ResidueFreeRemoval, #PrintedElectronics, #FlexibleElectronics

This is a highlight of the presentation:

Carrier and protection films for production processes

​

21 and 22 OCT 2026

Estrel, Berlin

Organised By:

TechBlick

​

More Highlights from the same talk.

05:32 - 07:50

When should a carrier film use acrylic, self-wetting silicone, or urethane adhesive?

When should a carrier film use acrylic, self-wetting silicone, or urethane adhesive?

The carrier film range comes in low-, medium-, and high-stick base versions so the material can be fine-tuned to the process. Acrylic is the entry-level adhesive for many processes, with good transmission, usually paired with an anti-static layer. It targets basic carrier applications and printing processes.

Silicone adhesive is self-wetting: laid on glass it protrudes and automatically settles, whereas acrylic typically needs roll-to-roll pressure lamination. This makes silicone popular for display applications and end-user installations where bubble-free installation is challenging. In non-clean-room conditions, thicker silicone can absorb particles and still guarantee proper adhesion to a display surface.

Urethane is the special case for vacuum bonding, sputtering, and vapor deposition. Silicone adhesive can show oil migration, and in vacuum it outgasses and contaminates the sputtering chamber. Urethane can provide the same structure with self-wetting behavior without that risk of contaminating the bonding or sputtering chamber.

In this short video, you can learn:
* Low-, medium-, and high-stick carrier versions let the adhesive be fine-tuned to the process.
* Silicone self-wets on glass, while acrylic usually requires roll-to-roll pressure lamination.
* Urethane avoids silicone oil migration and vacuum outgassing that can contaminate sputtering chambers.

πŸ“‹ **Clip Abstract** Carrier films use three stick levels and acrylic, silicone, or urethane adhesives to match printing, display, and vacuum processes. Acrylic suits basic carrier and printing steps, self-wetting silicone eases bubble-free display installation and particle tolerance, and urethane avoids silicone outgassing in vacuum bonding and sputtering.

About the speaker:
* Speaker: Christoph Bosshard
* Company: Kimoto
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#CarrierFilmAdhesives, #SelfWettingSilicone, #RollToRollLamination, #VacuumOutgassing, #PrintedElectronics, #DisplayManufacturing

12:59 - 13:54

Why does recycled polyester for high-optical carrier films still carry a 50% price premium?

Why does recycled polyester for high-optical carrier films still carry a 50% price premium?

Asked whether the sacrificial liner can be recycled, the answer starts with the base film: recycled polyester is already being introduced. But price dominates every conversation. Sources for these films exist and are being qualified, yet the material sits in a market where cost, not circularity, sets the agenda.

The hard part is optical quality. Finding recycled polyesters that reach the high optical standard is described as a genuine challenge, and even with sources now secured the price still runs 50% higher. For grades where every defect counts, the recycled route remains difficult.

For a carrier film that is sacrificial and never used long term, the picture eases: some recycled polyesters can be obtained at a lower mark-up. Even there it stays a challenge, and the outcome depends on the specific case rather than on any general rule.

In this short video, you can learn:
* Recycled base film is already being introduced, but price rather than recyclability drives the discussion.
* Sourcing recycled polyester that meets high optical quality is the core difficulty, and it still costs 50% more.
* Sacrificial carrier films not used long term can access recycled polyesters at a lower mark-up, though availability stays case-dependent.

πŸ“‹ **Clip Abstract** Sustainability questions about sacrificial liners resolve first into the base film: recycled polyester is being introduced, but optical-grade supply is hard to source and costs 50% more. For short-lived carrier films the premium narrows, yet the answer still depends on the specific application.

About the speaker:
* Speaker: Christoph Bosshard
* Company: Kimoto
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#RecycledPolyester, #SacrificialLiner, #CarrierFilm, #OpticalGradeFilm, #PrintedElectronics, #FlexibleElectronics

08:04 - 09:23

What flatness and thickness tolerances keep MicroLED mass-transfer parts from being lost?

What flatness and thickness tolerances keep MicroLED mass-transfer parts from being lost?

For MicroLED mass transfer, the carrier film is polyester with a double-sided silicone adhesive. One side is applied to a transparent glass layer, and the transparent film places the microLEDs on the second silicone layer. During placement, the thicker silicone layer absorbs. This construction is presented as a specific material for aligning and keeping very small parts in place.

The critical requirement is flatness. It must sit in very, very tight tolerances so no parts are lost during the process. The goal is that whatever number of parts is placed down, the same number remains at the end. Thickness and thickness tolerance across the whole surface are the critical points.

The process places microLEDs onto the second silicone layer, and flatness and thickness tolerance across the whole surface are framed as critical. The goal is preserving the same number of parts placed down through the end of the process. The next specific application is introduced after this MicroLED mass-transfer example.

In this short video, you can learn:
* The carrier film uses polyester plus a double-sided silicone adhesive, with one side applied to a transparent glass layer.
* The thicker silicone layer absorbs during placement of microLEDs on the second silicone layer.
* Flatness and thickness tolerance across the whole surface are critical to avoid losing parts in the process.

πŸ“‹ **Clip Abstract** A polyester carrier film with double-sided silicone adhesive is described for MicroLED mass transfer, with one side on a transparent glass layer and microLEDs placed on the second silicone layer. Flatness and thickness tolerance across the whole surface are critical so the same number of parts placed down remains at the end.

About the speaker:
* Speaker: Christoph Bosshard
* Company: Kimoto
* Event: Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

USA: The Future of Electronics RESHAPED | USA
πŸ“… Save the date: 9 and 10 June 2027
πŸ“ Mountain View, California (Silicon Valley)
πŸ“‹ Info: https://www.techblick.com/electronicsreshapedusa

Europe
The Future of Electronics RESHAPED | Berlin
πŸ“… Save the date: 20 and 21 October 2027
πŸ“ Berlin, Germany
πŸ“‹ Info: https://www.techblick.com/electronicsreshaped

#PolyesterCarrierFilm, #DoubleSidedSilicone, #MicroLEDMassTransfer, #ThicknessTolerance, #FlexibleElectronics, #DisplayManufacturing


About this talk

β†’ Carrier and protection films for production processes Β· Christoph Bosshard Β· The Future of Electronics RESHAPED 2026 Berlin


Other talks by Christoph Bosshard


More highlights from Christoph Bosshard

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page