top of page

Kris Erickson

Hewlett Packard

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Kris Erickson | Hewlett Packard: Can automated pick-and-place reliably connect 24-pad QFNs inside 3D-printed sockets?

16:29 - 18:27

Other snippets from this talk

Summary of the clip:

Can automated pick-and-place reliably connect 24-pad QFNs inside 3D-printed sockets?

The process creates sockets—regions where powder is later removed—so components can be placed into the printed part rather than only on its surface. The speaker notes that socket mounting can improve mechanical integrity, illustrating an LED placed in a socket and a resistor on the other side. This moves post-placement beyond manual assembly toward conventional automated pick-and-place and solder-paste deposition used in PCB manufacturing.

Using automated solder-paste deposition and automated component placement, the work pushed limits on component size and pad-to-pad spacing. The reported result: 24-pad QFNs were working most of the time, with well over 50% achieving all 24 pads successfully connected. The speaker frames this as still improvable, while two-terminal devices—resistors and LEDs—were successfully connected all the time after process optimization.

The print approach also allows a range of capacitors that can be printed, extending the discussion from interconnect and placement to printed components. The component workflow combines printed sockets, solder paste, and pick-and-place, with surface mounting as an alternative to socket mounting. Mechanical integrity is the stated reason sockets can be beneficial, especially when placing parts such as LEDs and resistors into a printed structure.

In this short video, you can learn:
* Printed sockets are regions where powder is removed so components can be placed into the part, with socket mounting optionally improving mechanical integrity.
* Automated solder-paste deposition and pick-and-place achieved well over 50% success connecting all 24 pads on 24-pad QFNs, though this remains improvable.
* Two-terminal resistors and LEDs were successfully connected all the time after process optimization.

📋 **Clip Abstract** The clip explains how 3D-printed sockets allow components to be placed into printed parts, with socket mounting used for mechanical integrity and surface mounting also possible. It then reports automated solder-paste and pick-and-place results: 24-pad QFNs connected all pads well over 50% of the time, while two-terminal resistors and LEDs connected successfully all the time after optimization.

About the speaker:
* Speaker: Kris Erickson
* Company: Hewlett Packard
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#AutomatedPickAndPlace, #SolderPasteDeposition, #24PadQFN, #PrintedComponentSockets, #PrintedElectronics, #3DElectronics

This is a highlight of the presentation:

3D Printing of Electronics using Multi Jet Fusion

Printed, Hybrid, Structural & 3D Electronics 2021

​

11-12 May 2021

Online

Organised By:

TechBlick

​

More Highlights from the same talk.

06:36 - 08:25

Why do 3D-printed circuits need a new CAD toolchain instead of existing EDA and mechanical CAD?

Why do 3D-printed circuits need a new CAD toolchain instead of existing EDA and mechanical CAD?

Conventional EDA tools are designed for flat two-dimensional PCBs, while mechanical CAD tools such as SolidWorks handle shape and form without electronics. As printed parts grow more complex, designing multilayer boards and complex traces inside a three-dimensional part becomes cumbersome across that divide. The mismatch appears early when traces, components and mechanical geometry must be co-designed rather than handled in separate environments.

The effort uses Rhino with a plugin in an open-source CAD approach. Circuit data from EDA tools such as Cadence and Eagle is brought in; users click where each component should sit and then auto-route the traces. When the three-dimensional design changes, they can regenerate the configuration, aiming for a result optimal both for electronic performance and for printability.

The key difference is three-dimensional routing. Traces can be produced in all three dimensions rather than staying on a two-dimensional plane with vias going down. The design can route organically throughout the part. That changes the design problem from placing flat PCB traces to generating a printable, electrically functional three-dimensional interconnect within the mechanical form.

In this short video, you can learn:
* Existing EDA tools target flat 2D PCBs, and mechanical CAD tools such as SolidWorks lack electronics, so complex 3D parts expose a toolchain gap.
* The workflow imports circuits from Cadence or Eagle into a Rhino plugin, places components by clicking, and auto-routes traces.
* Changing the 3D design allows regeneration of the trace configuration for electronic performance and printability, with routing in all three dimensions rather than 2D plus vias.

📋 **Clip Abstract** Complex 3D-printed electronics expose a mismatch between 2D-oriented EDA tools and electronics-free mechanical CAD. A Rhino plugin effort imports Cadence or Eagle circuits, enables click placement and auto-routing, regenerates designs when the 3D geometry changes, and supports organic three-dimensional traces instead of 2D routing with vias.

About the speaker:
* Speaker: Kris Erickson
* Company: Hewlett Packard
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#RhinoCADPlugin, #EDAToolchain, #AutoRouteTraces, #3DInterconnectRouting, #PrintedElectronics, #3DPrintedElectronics

20:29 - 22:42

Do printed conductive traces compromise Nylon 12 mechanical strength or sheet resistance?

Do printed conductive traces compromise Nylon 12 mechanical strength or sheet resistance?

Nylon 12 is the base material for many Multi Jet Fusion processes, with a modulus of 1,500 megapascal and ultimate tensile strength above 45 MPa. By placing conductive traces into this rigid engineering polymer, the overall printed parts retain similar mechanical properties. The trace itself can show differences, so the team optimizes the balance between conductivity and mechanical performance.

Where mechanical properties cannot be compromised, the approach targets good conductivity; where a slight mechanical hit is acceptable, it enables very good connectivity. Other current MJF materials are mostly amenable to the process, including options aimed at more flexibility or ductility rather than rigid polymers. Those flexible and ductile formulations remain more under development.

Connectivity results are close to 2D printed electronics: standard-process traces show single-digit milliohm per square sheet resistance. That supports use in many standard devices that do not drive high amperage or high power. When high amperage or high power is needed, a shared challenge arises in both 2D and 3D printed electronics.

In this short video, you can learn:
* Nylon 12 provides 1,500 MPa modulus and over 45 MPa UTS, and MJF parts with embedded traces retain similar overall mechanical properties.
* Trace-level mechanical differences are managed by optimizing conductivity or connectivity depending on the acceptable mechanical trade-off.
* Standard-process traces achieve single-digit milliohm per square sheet resistance, comparable to 2D printed electronics, for devices not driving high amperage or high power.

📋 **Clip Abstract** Multi Jet Fusion can embed conductive traces in Nylon 12 while maintaining overall mechanical properties similar to the base engineering polymer. Standard traces show single-digit milliohm per square sheet resistance, comparable to 2D printed electronics, though high-amperage or high-power use remains a shared challenge.

About the speaker:
* Speaker: Kris Erickson
* Company: Hewlett Packard
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#MultiJetFusion, #Nylon12Traces, #SheetResistance, #ConductiveTraces, #PrintedElectronics, #AdditiveElectronics

13:10 - 15:26

How wide a resistance range can you print by blending conductive and resistive agents in one layer?

How wide a resistance range can you print by blending conductive and resistive agents in one layer?

The printed resistor approach pairs a good conductive material with a less conductive, more resistive material that can be doped in. Design files print down as a composite rather than a single color, using both agents in different ratios within the same region. That ratio tunes high connectivity, low connectivity and the states between, with resistors shown in XY and Z orientations and at higher and lower conductivity.

The demonstration spans an entire nine orders of magnitude in bulk resistance, although tuning and tight resistor tolerances are described as earlier-stage work. With that range, geometry can extend performance further: a serpentine versus a smaller feature could theoretically go beyond it. That breadth supports the claim that the approach can meet any conventionally requested resistor.

The nine-order range also permits typical requested resistor values to be less than a square millimeter or a cubic millimeter in volume. Tight tolerances are still in progress, so the resistor work is presented as range-capable rather than fully dialed in. The next passive examined is the printed capacitor.

In this short video, you can learn:
* Blending conductive and resistive agents in different ratios within one region tunes connectivity from high to low.
* The printed resistor approach demonstrated a bulk-resistance span of nine orders of magnitude.
* Geometry, such as serpentine versus smaller features, could extend that resistance range further.

📋 **Clip Abstract** A printed resistor approach blends a good conductive material with a more resistive material that can be doped in, using different ratios inside the same printed region to tune connectivity in XY and Z. It demonstrates a nine-order-of-magnitude bulk-resistance span, with geometry offering further range and tight tolerances still in progress.

About the speaker:
* Speaker: Kris Erickson
* Company: Hewlett Packard
* Event: Printed, Hybrid, Structural & 3D Electronics 2021
* Location: Online

Join TechBlick - the home of printed electronics, additive electronics, flexible hybrid electronics and 3D electronics
https://www.techblick.com/

#PrintedResistor, #ConductiveResistiveBlending, #BulkResistanceRange, #NineOrdersMagnitude, #PrintedElectronics, #AdditiveElectronics


About this talk

→ 3D Printing of Electronics using Multi Jet Fusion · Kris Erickson · Printed, Hybrid, Structural, & 3D Electronics 2021


Other talks by Kris Erickson


More highlights from Kris Erickson

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page