Lina Kadura | CEA: How do you build a four-metal-layer PCB entirely additively without stacking substrates?
12:27 - 13:35
Other snippets from this talk
Summary of the clip:
How do you build a four-metal-layer PCB entirely additively without stacking substrates?
The clip defines complexity as two four-metal-layer PCBs. Each uses four silver-based metal layers and four printed insulating layers, so eight printing layers must be well aligned. Because the stack is four layers, printing is double-sided, and through vias are needed to interconnect all layers. Double-sided assembly is also required, with microcontrollers going down to a 400 micrometer pitch. That combination—eight aligned print layers, many vias, and fine-pitch double-sided assembly—is the starting point.
The build sequence starts with a PET substrate, although the speaker notes it can be any substrate. First, the vias are drilled and metallized. Then printing begins on top: metal one, dielectric, metal two, encapsulation. The same sequence is repeated on the other side. Finally, assembly completes the board. This is how a four-metal-layer, double-sided PCB is obtained additively, with printed metal, dielectric, encapsulation and vias forming the interconnect.
So the additive route is not one printed layer: it is eight aligned printing layers, four silver-based metals and four dielectrics, on both sides of a PET substrate. Through vias, drilled and metallized, interconnect the stack. Double-sided assembly places microcontrollers at 400 micrometer pitch. The speaker frames this as already complex: a four-metal-layer PCB made by printing metal, dielectric and encapsulation in sequence.
In this short video, you can learn:
* A four-metal-layer PCB uses four silver-based metal layers and four printed insulating layers, giving eight printing layers that must be well aligned.
* The process drills and metallizes vias first, then prints metal one, dielectric, metal two and encapsulation, repeating the same sequence on the other side before assembly.
* Double-sided assembly places microcontrollers down to 400 micrometer pitch, and the build starts on PET, although the speaker says it can be any substrate.
📋 **Clip Abstract** The clip explains how a four-metal-layer PCB can be built additively by starting with a PET substrate, drilling and metallizing through vias, and printing metal, dielectric, and encapsulation layers on both sides. It highlights eight aligned printing layers, silver-based metals, double-sided assembly, and microcontrollers at 400 micrometer pitch.
About the speaker:
* Speaker: Lina Kadura
* Company: CEA
* Event: The Future of Electronics RESHAPED 2025
* Location: Estrel, Berlin
🗓️ Save the date for the next Future of Electronic RESHAPED conference and exhibition
USA | Mountain View | 9-10 June 2027 : https://www.techblick.com/electronicsreshapedusa
Europe | Berlin | 20-21 October 2027: https://www.techblick.com/electronicsreshaped
#SilverBasedMetalLayers, #PETSubstrate, #ThroughViaMetallization, #FourMetalLayerPCB, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
Advancing PCB Technology Through Additive Manufacturing: Process, Sustainability, and Reliability
More Highlights from the same talk.
04:37 - 06:04
How much GWP reduction does additive PCB manufacturing deliver versus conventional FR4 boards?
How much GWP reduction does additive PCB manufacturing deliver versus conventional FR4 boards?
There is no stacking involved: everything is printed on both sides of the substrate. The life-cycle results come from a partner in Ecotron, using the methodology shown on screen and the Ecoinvent database. Partner ITENE normalised all results against the conventional PCB, the blue reference, then modelled two scenarios on top of that baseline.
Generation one, the brown bars, changes only the process while end-of-life stays identical, meaning both boards are incinerated, and it already gains about 50% in GWP. Generation two pushes the project's limits: one partner recycles the PCB, separating the PET from the silver, and another partner purifies that silver, so everything is assumed recycled.
The extra gain in generation two comes from two factors, PET production and silver, both now recycled, taking total GWP reduction from 50% to 60%. The Ecotron assessment also assumed an industrial scale, because every underlying measurement is lab-scale data rather than production data.
In this short video, you can learn:
* Normalised against the conventional PCB with an incineration end-of-life, the first-generation process alone already delivers roughly 50% GWP reduction.
* Separating PET from silver and purifying the silver lifts the total GWP gain to between 50% and 60%.
* All measurements are lab-scale, so the Ecotron assessment assumed industrial scale to make the comparison.
📋 **Clip Abstract** A life-cycle assessment normalised against the conventional PCB shows that switching to a printed, double-sided, stack-free process cuts GWP by about 50% with end-of-life unchanged. Adding PET separation and silver purification pushes the reduction to 50-60%, though the figures rest on lab-scale data scaled to industrial production.
About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#AdditivePCB, #EcoinventLCA, #SilverPurification, #GWPReduction, #PrintedElectronics, #SustainableElectronics
10:26 - 12:09
What makes screen-printed PCB fabrication a European re-industrialization opportunity?
What makes screen-printed PCB fabrication a European re-industrialization opportunity?
Subtractive versus additive is the obvious fabrication split, but the real point here is geography: both fabrication and materials are massively dominated by Asia. Even European PCB manufacturers hit a bottleneck on FR4 and cover. That dependency is reframed as an opportunity, because the ink and substrate providers are still quite European, which is the materials base for re-industrializing PCB production on the continent.
Screen printing is the chosen route at CEA, picked for high throughput, low cost and large-surface manufacturing, and upscalable through sheet-to-sheet or roll-to-roll. Inks span silver, copper-based and carbon systems. The resolution achieved today is documented, with headroom to go lower. The caveat: resolution must be managed by layer stacking and reproducibility once you target increasingly complex PCBs.
Beyond cost, screen printing is described as versatile: it offers a design flexibility that conventional PCB does not, expressed at the level of individual layers. Combine that with a still-European ink and substrate base, and screen-printed PCB fabrication becomes a re-industrialization argument, not simply a substitution of one deposition method for another.
In this short video, you can learn:
* Both PCB fabrication and its materials are massively dominated by Asia, leaving even European manufacturers with an FR4 and cover bottleneck.
* Screen printing was selected for high throughput, low cost, large surface area and sheet-to-sheet or roll-to-roll upscalability.
* Resolution must be handled through layer stacking and reproducibility as PCB complexity rises.
📋 **Clip Abstract** Additive screen printing replaces the subtractive flow, but the strategic point is supply: FR4 and cover stock come from Asia while inks and substrates remain largely European. CEA's screen-printing route, using silver, copper or carbon and upscalable sheet-to-sheet or roll-to-roll, trades resolution headroom for throughput and layer-level design freedom.
About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#ScreenPrinting, #AdditivePCBFabrication, #FR4SupplyChain, #LayerStacking, #PrintedElectronics, #SustainableElectronics
08:23 - 10:08
Why can't conventional PCB CAD tools automatically design-check a printed multilayer board?
Why can't conventional PCB CAD tools automatically design-check a printed multilayer board?
The schematic does not depend on the fabrication step, so it stays identical between conventional and printed technologies. The layout does not: it depends entirely on the fabrication process, the design rules you set, your layer stack, the thicknesses, and the materials you use. That is where the two flows diverge, before any board is built.
In the conventional flow you draw copper traces most of the time and do not draw the insulator, because the substrate is FR4. In printed electronics you must also lay out the dielectric insulator, since you print it as well. Vias differ too: conventionally they are drilled through all the substrates that are then stacked.
In printed electronics only the vias in the core or substrates need drilling; all the others between layers are printed, simply an area where no dielectric is deposited, so they are free — included directly in the dielectric layer design. The gap: no CAD tool today offers automatic design rule checking for complex printed PCBs.
In this short video, you can learn:
* Schematic capture is identical across the two technologies; only the layout depends on fabrication, design rules, layer stack, thicknesses and materials.
* Conventional FR4 design draws copper only, whereas printed electronics must also lay out the dielectric insulator that has to be printed.
* Only core and substrate vias are drilled in printed boards; interlayer vias are printed dielectric-free areas, and no CAD tool yet automatically checks such complex designs.
📋 **Clip Abstract** Layout, not schematic, is where printed and conventional PCB design split: printed boards need the dielectric drawn and interlayer vias printed rather than drilled. Conventional CAD tools are established and efficient, but none yet offers automatic design rule checking for complex printed PCBs — a real limit on fabricating them.
About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#DesignRuleCheck, #PrintedDielectric, #ViaDrilling, #LayerStackDesign, #PrintedElectronics, #SustainableElectronics
Other talks by Lina Kadura
- From Subtractive to Additive: Transforming PCB Production for Sustainable Electronics · Sustainable Electronics RESHAPED 2026 Berlin
- Printed processes for PCBs manufacturing: towards sustainable electronics · Printed Electronics Innovation Day | Winter 2024
More highlights from Lina Kadura
- ▶ How much GWP reduction does additive PCB manufacturing deliver versus conventional FR4 boards? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ Why can't conventional PCB CAD tools automatically design-check a printed multilayer board? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ What makes screen-printed PCB fabrication a European re-industrialization opportunity? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ Can printed PCBs be assembled with standard SAC-305 reflow and IPC processes? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ Can we really slash PCB carbon footprint by 50% simply by switching from subtractive etching to additive screen printing? · Printed Electronics Innovation Day 2024
- ▶ How do you design and print an 8-layer additive stackup with 200-micron vias on a single flexible PET sheet? · Printed Electronics Innovation Day 2024
- ▶ What are the physical resolution and conductivity trade-offs when shifting from bulk copper to screen-printed silver inks? · Printed Electronics Innovation Day 2024


