top of page

Lina Kadura

CEA

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Lina Kadura | CEA: Can we really slash PCB carbon footprint by 50% simply by switching from subtractive etching to additive screen printing?

00:03:07.085 - 00:04:52.225

Other snippets from this talk

Summary of the clip:

Can we really slash PCB carbon footprint by 50% simply by switching from subtractive etching to additive screen printing?

Conventional printed circuit boards (PCBs) rely heavily on glass-reinforced epoxy (FR4) substrates and subtractive wet-chemical etching of copper. This established manufacturing paradigm is resource-intensive, generates substantial chemical waste, and suffers from low end-of-life recyclability.

Transitioning to additive printed electronics presents a massive environmental advantage. Life cycle assessments reveal that merely changing the manufacturing process from subtractive to additive—while maintaining the same FR4 substrate—reduces the global warming potential of the board by 50%.

Further environmental dividends are unlocked by swapping the rigid substrate itself for flexible or bio-based materials. This strategy establishes a pathway toward truly circular electronics, matching conventional performance while dramatically lowering the carbon and material footprint of electronic assemblies.

In this short video, you can learn:
* Why subtractive copper etching dominates conventional PCB waste metrics.
* How additive manufacturing steps reduce global warming potential by half.
* The impact of substrate selection on the life cycle assessment of printed circuits.
📋 **Clip Abstract** CEA researchers demonstrate that transitioning from conventional FR4 subtractive processes to additive printing yields a 50% reduction in global warming potential. This process paves the way for sustainable electronics with minimal structural waste.

#AdditiveScreenPrinting, #SubtractiveEtching, #FR4Substrates, #CopperEtching, #PrintedElectronics, #CircularElectronics

This is a highlight of the presentation:

​

Printed Electronics Innovation Day 2024

Display Innovation Day 2024

​

TechBlick | Online Platform

Organised By:

TechBlick

​

More Highlights from the same talk.

04:37 - 06:04

How much GWP reduction does additive PCB manufacturing deliver versus conventional FR4 boards?

How much GWP reduction does additive PCB manufacturing deliver versus conventional FR4 boards?

There is no stacking involved: everything is printed on both sides of the substrate. The life-cycle results come from a partner in Ecotron, using the methodology shown on screen and the Ecoinvent database. Partner ITENE normalised all results against the conventional PCB, the blue reference, then modelled two scenarios on top of that baseline.

Generation one, the brown bars, changes only the process while end-of-life stays identical, meaning both boards are incinerated, and it already gains about 50% in GWP. Generation two pushes the project's limits: one partner recycles the PCB, separating the PET from the silver, and another partner purifies that silver, so everything is assumed recycled.

The extra gain in generation two comes from two factors, PET production and silver, both now recycled, taking total GWP reduction from 50% to 60%. The Ecotron assessment also assumed an industrial scale, because every underlying measurement is lab-scale data rather than production data.

In this short video, you can learn:
* Normalised against the conventional PCB with an incineration end-of-life, the first-generation process alone already delivers roughly 50% GWP reduction.
* Separating PET from silver and purifying the silver lifts the total GWP gain to between 50% and 60%.
* All measurements are lab-scale, so the Ecotron assessment assumed industrial scale to make the comparison.

📋 **Clip Abstract** A life-cycle assessment normalised against the conventional PCB shows that switching to a printed, double-sided, stack-free process cuts GWP by about 50% with end-of-life unchanged. Adding PET separation and silver purification pushes the reduction to 50-60%, though the figures rest on lab-scale data scaled to industrial production.

About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#AdditivePCB, #EcoinventLCA, #SilverPurification, #GWPReduction, #PrintedElectronics, #SustainableElectronics

10:26 - 12:09

What makes screen-printed PCB fabrication a European re-industrialization opportunity?

What makes screen-printed PCB fabrication a European re-industrialization opportunity?

Subtractive versus additive is the obvious fabrication split, but the real point here is geography: both fabrication and materials are massively dominated by Asia. Even European PCB manufacturers hit a bottleneck on FR4 and cover. That dependency is reframed as an opportunity, because the ink and substrate providers are still quite European, which is the materials base for re-industrializing PCB production on the continent.

Screen printing is the chosen route at CEA, picked for high throughput, low cost and large-surface manufacturing, and upscalable through sheet-to-sheet or roll-to-roll. Inks span silver, copper-based and carbon systems. The resolution achieved today is documented, with headroom to go lower. The caveat: resolution must be managed by layer stacking and reproducibility once you target increasingly complex PCBs.

Beyond cost, screen printing is described as versatile: it offers a design flexibility that conventional PCB does not, expressed at the level of individual layers. Combine that with a still-European ink and substrate base, and screen-printed PCB fabrication becomes a re-industrialization argument, not simply a substitution of one deposition method for another.

In this short video, you can learn:
* Both PCB fabrication and its materials are massively dominated by Asia, leaving even European manufacturers with an FR4 and cover bottleneck.
* Screen printing was selected for high throughput, low cost, large surface area and sheet-to-sheet or roll-to-roll upscalability.
* Resolution must be handled through layer stacking and reproducibility as PCB complexity rises.

📋 **Clip Abstract** Additive screen printing replaces the subtractive flow, but the strategic point is supply: FR4 and cover stock come from Asia while inks and substrates remain largely European. CEA's screen-printing route, using silver, copper or carbon and upscalable sheet-to-sheet or roll-to-roll, trades resolution headroom for throughput and layer-level design freedom.

About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#ScreenPrinting, #AdditivePCBFabrication, #FR4SupplyChain, #LayerStacking, #PrintedElectronics, #SustainableElectronics

08:23 - 10:08

Why can't conventional PCB CAD tools automatically design-check a printed multilayer board?

Why can't conventional PCB CAD tools automatically design-check a printed multilayer board?

The schematic does not depend on the fabrication step, so it stays identical between conventional and printed technologies. The layout does not: it depends entirely on the fabrication process, the design rules you set, your layer stack, the thicknesses, and the materials you use. That is where the two flows diverge, before any board is built.

In the conventional flow you draw copper traces most of the time and do not draw the insulator, because the substrate is FR4. In printed electronics you must also lay out the dielectric insulator, since you print it as well. Vias differ too: conventionally they are drilled through all the substrates that are then stacked.

In printed electronics only the vias in the core or substrates need drilling; all the others between layers are printed, simply an area where no dielectric is deposited, so they are free — included directly in the dielectric layer design. The gap: no CAD tool today offers automatic design rule checking for complex printed PCBs.

In this short video, you can learn:
* Schematic capture is identical across the two technologies; only the layout depends on fabrication, design rules, layer stack, thicknesses and materials.
* Conventional FR4 design draws copper only, whereas printed electronics must also lay out the dielectric insulator that has to be printed.
* Only core and substrate vias are drilled in printed boards; interlayer vias are printed dielectric-free areas, and no CAD tool yet automatically checks such complex designs.

📋 **Clip Abstract** Layout, not schematic, is where printed and conventional PCB design split: printed boards need the dielectric drawn and interlayer vias printed rather than drilled. Conventional CAD tools are established and efficient, but none yet offers automatic design rule checking for complex printed PCBs — a real limit on fabricating them.

About the speaker:
* Speaker: Lina Kadura
* Company: CEA- Liten
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#DesignRuleCheck, #PrintedDielectric, #ViaDrilling, #LayerStackDesign, #PrintedElectronics, #SustainableElectronics


Other talks by Lina Kadura


More highlights from Lina Kadura

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page