top of page

Thomas Achleitner

EV Group

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Thomas Achleitner | EV Group: Why is shifting from spin coating to inkjet deposition the ultimate breakthrough for controlling residual layer thickness in nanoimprinting?

00:11:05 - 00:13:37

Other snippets from this talk

Summary of the clip:

Why is shifting from spin coating to inkjet deposition the ultimate breakthrough for controlling residual layer thickness in nanoimprinting?

A persistent challenge in nanoimprint lithography is managing the residual layer thickness (RLT) across varying feature densities, which directly impacts subsequent plasma etching steps. Through a strategic partnership with Notion Systems, EV Group has integrated precise inkjet coating into their nanoimprint systems. This replaces conventional spin coating with a drop-on-demand dispense system that dramatically improves material utilization and process flexibility.

Inkjet coating enables advanced capabilities such as grayscale printing and selective-area deposition, allowing localized control of the initial resist thickness from 20 nm to nearly 100 nm. By optimizing the droplet pattern based on local structure volume, manufacturers can achieve an exceptionally uniform residual layer across the entire wafer. This minimizes material waste and simplifies fab-level chemical management.

The practical manufacturing benefit of this joint technology is demonstrated by achieving a residual layer thickness of less than 20 nanometers on complex metalens structures. Minimizing this non-structured barrier layer significantly accelerates downstream reactive ion etching (RIE) processes, preventing pattern distortion and improving overall yield.

In this short video, you can learn:
* How integrating inkjet deposition into NIL tooling replaces traditional spin coating to improve cost-of-ownership and material waste.
* The mechanism behind achieving uniform residual layer thickness (RLT) by matching droplet volume to local feature density.
* How reducing the residual layer thickness to under 20 nm optimizes downstream dry etching steps for metalenses.

πŸ“‹ **Clip Abstract** This clip highlights the collaboration between EVG and Notion Systems to integrate inkjet deposition into nanoimprint lithography workflows. By replacing spin coating with drop-on-demand inkjetting, manufacturers can control residual layer thickness down to under 20 nm, optimizing the etching process for optical nanostructures.

πŸ”— Link in comments πŸ‘‡

#NanoimprintLithography, #InkjetDeposition, #ResidualLayerThickness, #MetalensManufacturing, #DiffractiveOpticalElements, #ARWaveguides

This is a highlight of the presentation:

​

AR, VR, and MR Vision Systems 2023: Innovations, Promising Start-Ups, Future Roadmap

​

​

TechBlick Platform | Online

Organised By:

TechBlick

​

More Highlights from the same talk.

02:41 - 04:47

A single AR master can cost hundreds of thousands of euros β€” how do you replicate it 21 times on 300mm without drift?

A single AR master can cost hundreds of thousands of euros β€” how do you replicate it 21 times on 300mm without drift?

Mastering starts from a single die-hard master, which the step-and-repeat system upscales to fully populate the master β€” a three-picture process flow on paper. Behind it sit more than six years of process development: a reliable polymer combination, a system that moves reliably, and demolding done precisely and carefully. That matters commercially, because one hard master can cost a few hundred thousand euros, particularly when it is a single, super-fancy die.

Scaling a single die to 300 millimetre or panel size is where this becomes unavoidable: there is currently no other way to master it, which is why the approach is so important for 300 millimetre and beyond. On the slide from Jason, 24 dies were mentioned; this work shows at least 21, and shuffling the layout could squeeze in one or two more.

FBM metrology across those 21 dies shows no big change from the first die to the last die, confirming a very stable polymer combination for the step-and-repeat mastering shop that is long-lasting for the master itself. Critically, it is compatible with downstream processing such as the antistick layer and other preservation strategies, and there is considerable flexibility in how the step-and-repeat hard master is designed.

In this short video, you can learn:
* More than six years of process development went into the polymer combination and precise, careful demolding required for reliable step-and-repeat mastering.
* One hard master can cost a few hundred thousand euros, so replicating it rather than remastering it is where the cost is saved.
* FBM metrology across 21 dies showed no big change from the first die to the last, and the stack stays compatible with antistick layers and preservation strategies.

πŸ“‹ **Clip Abstract** Step-and-repeat mastering upscales a single die-hard master to 300 millimetre and panel formats, placing at least 21 dies per master with no big change from the first die to the last. That stability rests on six years of polymer and demolding development, and on compatibility with antistick layers and other downstream preservation steps.

About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven

#StepAndRepeatMastering, #AntistickLayer, #FBMMetrology, #PolymerDemolding, #ARDisplays, #ARWaveguides

09:03 - 11:30

Why does inkjet coating beat spin coating for AR gratings β€” and how thin can the residual layer get?

Why does inkjet coating beat spin coating for AR gratings β€” and how thin can the residual layer get?

Spin coating leaves a residual layer whose thickness tracks the grating height, because that is the nature of the process. Inkjet coating changes the outcome: it keeps the residual layer low and genuinely uniform, independent of the structure height. The stated goal is to further increase the efficiency of the AR effect. That uniformity, not throughput, is the reason the coating step matters for diffractive waveguide performance.

A comprehensive study was run with partner Techcent in Dresden, which fabricated a fancy master carrying an in-coupler grating, an extended grating and an out-coupler grating. The in-coupler carries staircase gratings. The extended grating has height modulation, progressing from 60 nanometres down to 160 nanometres. The out-coupler has a non-linear height progression from 50 to 200 nanometres. Duty cycle and pitch also change along the gratings.

Inkjet coating was used to achieve a really thin, homogeneous residual layer thickness below the structures. Results: on the out-coupler grating, the most sensitive case, a residual layer thickness in the range of 50 nanometres was achieved, very constant and very thin. The extended and out-coupler gratings gave 60 and 45 nanometres. Everything was processed with high refractive index materials, so the process is up and running and ready for demo in the competence centre.

In this short video, you can learn:
* Spin coating ties residual layer thickness to grating height, while inkjet coating decouples them.
* The Dresden master combined staircase in-coupler gratings, a height-modulated extended grating and a non-linear 50–200 nm out-coupler grating with changing duty cycle and pitch.
* Constant residual layers of 50 nm on the most sensitive out-coupler grating, and 60 and 45 nm on the extended and out-coupler gratings, were achieved using high refractive index materials.

πŸ“‹ **Clip Abstract** Inkjet coating replaces spin coating to keep a low, uniform residual layer under diffractive AR gratings regardless of structure height, raising efficiency. A Techcent Dresden master with staircase, height-modulated and non-linear gratings was imprinted in high refractive index material, delivering constant residual layers of about 50, 60 and 45 nanometres and a demo-ready process.

About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven

#NanoimprintLithography, #InkjetCoating, #HighIndexMaterials, #ResidualLayerThickness, #ARWaveguides, #Nanofabrication

06:37 - 08:48

Can you imprint both sides of a 12-inch wafer to Β±5 arc seconds without destroying the first layer?

Can you imprint both sides of a 12-inch wafer to Β±5 arc seconds without destroying the first layer?

Dual side imprinting is a hot topic because it enables different structures on the first side of the wafer and, after flipping the substrate, on the back side. The flow looks simple: take the first-side-imprinted wafer, coat a protective layer over side one, flip the wafer, process side two, then remove that protective layer. The result is two precisely aligned nanoimprinted layers.

Along that process flow sit several question marks. How compatible is the protective layer with the imprinting polymer? How do you remove the protective layer after imprinting without destroying the underlying polymer? And what about the angular alignment accuracy? These questions sit between the clean-looking flow and a working dual-side process, each one tied to material choices and tool behaviour rather than to the imprint step alone.

The answers come from process development in the lab. An off-the-shelf protective layer coating has already been demonstrated with high refractive index and low refractive index materials, and it is compatible with many resins. A two-chemistry clean removes that protective layer coating after second-side imprinting. Angular alignment accuracy reaches Β±5 arc seconds on 12-inch, which customer information says is more than enough to increase optical output.

In this short video, you can learn:
* Dual-side imprinting requires flipping the wafer between front-side and back-side structures, with a protective layer in between.
* The open questions are protective-layer compatibility with the imprint polymer and its removal without destroying the underlying polymer.
* Angular alignment reaches Β±5 arc seconds on 12-inch, which customer information says is enough to increase optical output.

πŸ“‹ **Clip Abstract** Dual-side nanoimprint lithography enables different structures on both sides of a wafer, using a protective coating and a wafer flip between the two imprints. Process development has shown an off-the-shelf protective layer compatible with high- and low-refractive-index materials and many resins, a two-chemistry clean for its removal, and Β±5 arc seconds angular alignment on 12-inch, which customer information says is more than enough to increase optical output.

About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven

#DualSideImprinting, #ProtectiveLayerCoating, #HighRefractiveIndex, #AngularAlignment, #NanoimprintLithography, #ARDisplays

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page