Thomas Achleitner | EV Group: What is the step-by-step engineering process behind producing high-fidelity working stamps for nanoimprint replication?
00:07:56 - 00:09:34
Other snippets from this talk
Summary of the clip:
What is the step-by-step engineering process behind producing high-fidelity working stamps for nanoimprint replication?
Achieving high-fidelity sub-micron replication requires a highly controlled and repeatable stamp fabrication process. The Smart NIL workflow begins by spin-coating the step-and-repeat master with an interlayer, followed by the deposition of a specialized working stamp polymer. A flexible backplane is then attached, and the entire stack is UV-cured before being gently released to yield a durable, reusable working stamp.
Once the working stamp is fabricated, the target substrate is prepared using a primer and an imprint resist layer. The flexible working stamp is systematically brought into contact with the coated wafer, UV-cured to lock in the nanostructures, and subsequently released. This cycle can be repeated hundreds of times from a single working stamp, preserving the integrity of the original master.
The resulting prints demonstrate exceptional 1-to-1 pattern replication with high fidelity over large surface areas, completely independent of feature geometry or orientation. This single-shot replication method is highly effective for fabricating complex nanostructures, including the high-index slanted gratings commonly used in modern augmented reality waveguides.
In this short video, you can learn:
* The multi-layer polymer stacking and UV-curing sequence required to construct a durable working stamp.
* How flexible working stamps maintain high-fidelity pattern transfer across large-area substrates.
* Why this single-shot NIL replication process is ideal for complex, multi-directional features like AR waveguide gratings.
π **Clip Abstract** This technical walk-through details the physical process of fabricating working stamps and replicating nano-features using EVG's Smart NIL system. The method achieves highly precise, single-shot pattern transfers across large-area wafers, making it ideal for delicate AR optical architectures.
π Link in comments π
#SmartNIL, #NanoimprintLithography, #WorkingStamp, #SlantedGratings, #ARWaveguides, #DiffractiveOpticalElements
This is a highlight of the presentation:
More Highlights from the same talk.
02:41 - 04:47
A single AR master can cost hundreds of thousands of euros β how do you replicate it 21 times on 300mm without drift?
A single AR master can cost hundreds of thousands of euros β how do you replicate it 21 times on 300mm without drift?
Mastering starts from a single die-hard master, which the step-and-repeat system upscales to fully populate the master β a three-picture process flow on paper. Behind it sit more than six years of process development: a reliable polymer combination, a system that moves reliably, and demolding done precisely and carefully. That matters commercially, because one hard master can cost a few hundred thousand euros, particularly when it is a single, super-fancy die.
Scaling a single die to 300 millimetre or panel size is where this becomes unavoidable: there is currently no other way to master it, which is why the approach is so important for 300 millimetre and beyond. On the slide from Jason, 24 dies were mentioned; this work shows at least 21, and shuffling the layout could squeeze in one or two more.
FBM metrology across those 21 dies shows no big change from the first die to the last die, confirming a very stable polymer combination for the step-and-repeat mastering shop that is long-lasting for the master itself. Critically, it is compatible with downstream processing such as the antistick layer and other preservation strategies, and there is considerable flexibility in how the step-and-repeat hard master is designed.
In this short video, you can learn:
* More than six years of process development went into the polymer combination and precise, careful demolding required for reliable step-and-repeat mastering.
* One hard master can cost a few hundred thousand euros, so replicating it rather than remastering it is where the cost is saved.
* FBM metrology across 21 dies showed no big change from the first die to the last, and the stack stays compatible with antistick layers and preservation strategies.
π **Clip Abstract** Step-and-repeat mastering upscales a single die-hard master to 300 millimetre and panel formats, placing at least 21 dies per master with no big change from the first die to the last. That stability rests on six years of polymer and demolding development, and on compatibility with antistick layers and other downstream preservation steps.
About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven
#StepAndRepeatMastering, #AntistickLayer, #FBMMetrology, #PolymerDemolding, #ARDisplays, #ARWaveguides
09:03 - 11:30
Why does inkjet coating beat spin coating for AR gratings β and how thin can the residual layer get?
Why does inkjet coating beat spin coating for AR gratings β and how thin can the residual layer get?
Spin coating leaves a residual layer whose thickness tracks the grating height, because that is the nature of the process. Inkjet coating changes the outcome: it keeps the residual layer low and genuinely uniform, independent of the structure height. The stated goal is to further increase the efficiency of the AR effect. That uniformity, not throughput, is the reason the coating step matters for diffractive waveguide performance.
A comprehensive study was run with partner Techcent in Dresden, which fabricated a fancy master carrying an in-coupler grating, an extended grating and an out-coupler grating. The in-coupler carries staircase gratings. The extended grating has height modulation, progressing from 60 nanometres down to 160 nanometres. The out-coupler has a non-linear height progression from 50 to 200 nanometres. Duty cycle and pitch also change along the gratings.
Inkjet coating was used to achieve a really thin, homogeneous residual layer thickness below the structures. Results: on the out-coupler grating, the most sensitive case, a residual layer thickness in the range of 50 nanometres was achieved, very constant and very thin. The extended and out-coupler gratings gave 60 and 45 nanometres. Everything was processed with high refractive index materials, so the process is up and running and ready for demo in the competence centre.
In this short video, you can learn:
* Spin coating ties residual layer thickness to grating height, while inkjet coating decouples them.
* The Dresden master combined staircase in-coupler gratings, a height-modulated extended grating and a non-linear 50β200 nm out-coupler grating with changing duty cycle and pitch.
* Constant residual layers of 50 nm on the most sensitive out-coupler grating, and 60 and 45 nm on the extended and out-coupler gratings, were achieved using high refractive index materials.
π **Clip Abstract** Inkjet coating replaces spin coating to keep a low, uniform residual layer under diffractive AR gratings regardless of structure height, raising efficiency. A Techcent Dresden master with staircase, height-modulated and non-linear gratings was imprinted in high refractive index material, delivering constant residual layers of about 50, 60 and 45 nanometres and a demo-ready process.
About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven
#NanoimprintLithography, #InkjetCoating, #HighIndexMaterials, #ResidualLayerThickness, #ARWaveguides, #Nanofabrication
06:37 - 08:48
Can you imprint both sides of a 12-inch wafer to Β±5 arc seconds without destroying the first layer?
Can you imprint both sides of a 12-inch wafer to Β±5 arc seconds without destroying the first layer?
Dual side imprinting is a hot topic because it enables different structures on the first side of the wafer and, after flipping the substrate, on the back side. The flow looks simple: take the first-side-imprinted wafer, coat a protective layer over side one, flip the wafer, process side two, then remove that protective layer. The result is two precisely aligned nanoimprinted layers.
Along that process flow sit several question marks. How compatible is the protective layer with the imprinting polymer? How do you remove the protective layer after imprinting without destroying the underlying polymer? And what about the angular alignment accuracy? These questions sit between the clean-looking flow and a working dual-side process, each one tied to material choices and tool behaviour rather than to the imprint step alone.
The answers come from process development in the lab. An off-the-shelf protective layer coating has already been demonstrated with high refractive index and low refractive index materials, and it is compatible with many resins. A two-chemistry clean removes that protective layer coating after second-side imprinting. Angular alignment accuracy reaches Β±5 arc seconds on 12-inch, which customer information says is more than enough to increase optical output.
In this short video, you can learn:
* Dual-side imprinting requires flipping the wafer between front-side and back-side structures, with a protective layer in between.
* The open questions are protective-layer compatibility with the imprint polymer and its removal without destroying the underlying polymer.
* Angular alignment reaches Β±5 arc seconds on 12-inch, which customer information says is enough to increase optical output.
π **Clip Abstract** Dual-side nanoimprint lithography enables different structures on both sides of a wafer, using a protective coating and a wafer flip between the two imprints. Process development has shown an off-the-shelf protective layer compatible with high- and low-refractive-index materials and many resins, a two-chemistry clean for its removal, and Β±5 arc seconds angular alignment on 12-inch, which customer information says is more than enough to increase optical output.
About the speaker:
* Speaker: Thomas Achleitner
* Company: EV Group (EVG)
* Event: Eindhoven 2026
* Location: High Tech Campus, Eindhoven
#DualSideImprinting, #ProtectiveLayerCoating, #HighRefractiveIndex, #AngularAlignment, #NanoimprintLithography, #ARDisplays
Other talks by Thomas Achleitner
- Nano Imprinting Lithography From Single DIE to Wafer-Level HVM Β· AR, VR, and MR Vision Systems: Innovations, Promising Start-Ups, Future Roadmap
More highlights from Thomas Achleitner
- βΆ A single AR master can cost hundreds of thousands of euros β how do you replicate it 21 times on 300mm without drift? Β· MicroLED Connect 2026
- βΆ Can you imprint both sides of a 12-inch wafer to Β±5 arc seconds without destroying the first layer? Β· MicroLED Connect 2026
- βΆ Why does inkjet coating beat spin coating for AR gratings β and how thin can the residual layer get? Β· MicroLED Connect 2026
- βΆ How do you align micro-lens arrays to a 50Β΅m-thick microLED wafer at Β±500nm and still package it? Β· MicroLED Connect 2026
- βΆ How can we overcome the costly and time-consuming mastering bottleneck in nanoimprint lithography for AR waveguides and metalenses? Β· AR, VR, and MR Vision Systems 2023: Innovations, Promising Start-Ups, Future Roadmap
- βΆ Why is shifting from spin coating to inkjet deposition the ultimate breakthrough for controlling residual layer thickness in nanoimprinting? Β· AR, VR, and MR Vision Systems 2023: Innovations, Promising Start-Ups, Future Roadmap

