Yousef Farraj | SOLRA-PV: Why Do High-Efficiency Perovskites Often Fail Commercially Due to "Dead Area" Losses?
00:06:02 - 00:08:12
Other snippets from this talk
Summary of the clip:
Why Do High-Efficiency Perovskites Often Fail Commercially Due to "Dead Area" Losses?
Transitioning from single-cell lab PV devices to multi-cell modules requires interconnecting individual cells in series to elevate output voltage. Traditionally, screen printing requires physical shifts between layer depositions to create these series connections, which introduces a massive "dead area" where light is not harvested. This geometric constraint can drop the active area of a module down to just 50%, completely erasing any materials-level efficiency advantages over silicon.
To solve this scaling bottleneck, laser patterning is implemented using a P1, P2, and P3 scribing sequence. In the critical P2 step, laser parameters must be tuned to selectively ablate the upper layers—including the printed ITO, zirconia, and titania—without damaging the delicate fluorine-doped tin oxide (FTO) front electrode beneath.
By transitioning from physical print-shifting to high-precision laser etching, the geometric fill factor increases from 50% to 88%, matching conventional silicon standards. Optimizing this toolpath to incorporate the final P3 scribe is projected to push the active area beyond 95%, maximizing total power density.
In this short video, you can learn:
* Why traditional print-shifting drastically limits the active area of multi-cell PV modules.
* The mechanics of selective laser ablation (P1-P3) to preserve underlying transparent conductive electrodes.
* How optimizing geometric fill factors to 88%+ bridges the gap between perovskite and silicon performance.
📋 **Clip Abstract** The speaker explains how high-precision laser etching overcomes the massive "dead area" losses of standard printed cell interconnections. By replacing print-shifting with selective P1, P2, and P3 laser scribing, active module area can be elevated past 88%.
#LaserScribing, #GeometricFillFactor, #SelectiveLaserAblation, #PerovskiteSolarModules, #PrintedElectronics, #ThinFilmPhotovoltaics
This is a highlight of the presentation:
The Industrialization of Perovskite-Based Indoor Photovoltaics
More Highlights from the same talk.
00:02:35 - 00:03:55
Can We Design a Perovskite Solar Cell That Is 100% Recyclable Without Scraping the Electrodes?
Can We Design a Perovskite Solar Cell That Is 100% Recyclable Without Scraping the Electrodes?
Standard photovoltaic recycling is an energy-intensive, destructive process that usually recovers only bulk glass or silicon fractions. SOLRA-PV overcomes this bottleneck by utilizing a triple-mesoscopic oxide scaffold printed via screen printing. By sequentially printing titania (TiO2), zirconia (ZrO2), and indium tin oxide (ITO) layers on a transparent conductive oxide substrate, they create a highly porous matrix that can be infiltrated by a perovskite precursor in a single step.
Because the active perovskite material is deposited as the final phase via slot-die coating and remains chemically accessible within the mesoporous scaffold, it can be completely dissolved back out of the matrix using a simple solvent wash. This non-destructive process preserves the underlying screen-printed titanium and zirconium oxide ceramic layers entirely.
Experimental results demonstrate that once the spent perovskite is stripped, a fresh precursor can be re-infiltrated into the original mesoporous oxide stack. The recycled panel achieves the exact same conversion efficiency as the pristine device, unlocking a multi-cycle circular economy for indoor IoT harvesters.
In this short video, you can learn:
* How a mesoscopic TiO2/ZrO2/ITO scaffold enables non-destructive active layer stripping.
* The screen-printing and slot-die deposition sequences used to build the recyclable cell.
* Performance verification showing zero efficiency loss after multiple stripping and re-deposition cycles.
📋 **Clip Abstract** This clip highlights SOLRA-PV's unique mesoscopic design that allows the active perovskite material to be easily dissolved and re-deposited. This technique preserves the ceramic layers, offering a highly sustainable and simple recycling method for indoor PV panels.
#MesoscopicScaffold, #PerovskitePhotovoltaics, #ActiveLayerStripping, #ScreenPrintedElectronics, #IndoorEnergyHarvesting, #CircularElectronics
2:57 - 3:47
Can tuning the perovskite bandgap to 1.8 eV solve both indoor efficiency and degradation bottlenecks?
Can tuning the perovskite bandgap to 1.8 eV solve both indoor efficiency and degradation bottlenecks?
Unlike traditional outdoor silicon photovoltaics optimized for the AM1.5G solar spectrum, indoor light energy harvesting requires custom bandgap engineering. By adjusting the composition of hybrid organic-inorganic lead halide perovskites, the absorption edge can be systematically shifted to wider bandgaps of 1.7 to 1.8 eV. This perfect spectral match with common artificial light sources, such as LEDs and fluorescent tubes, drastically minimizes thermalization losses and maximizes power conversion efficiency under low-lux environments.
Operating indoors also radically alters the device degradation pathways. The absence of high-energy ultraviolet (UV) photons from artificial indoor bulbs eliminates one of the primary drivers of photocatalytic perovskite degradation typically observed in outdoor deployment. This allows material scientists to pivot their optimization efforts entirely toward moisture and oxygen barriers, rather than complex UV-stabilizing additives.
To address the remaining thermodynamic instabilities of the perovskite crystal lattice, researchers utilize the Goldschmidt tolerance factor as a structural guide. By precisely substituting cations within the crystal framework, the structural stability of the perovskite phase is secured. Combined with robust edge-seal polymer encapsulants, these tuned wide-bandgap cells can maintain reliable long-term operations without the threat of phase transition or rapid moisture-induced decomposition.
In this short video, you can learn:
* How wide-bandgap engineering (1.7–1.8 eV) optimizes spectral response for indoor artificial lighting.
* Why indoor environments bypass the severe UV-degradation challenges plaguing outdoor perovskite modules.
* The use of the Goldschmidt tolerance factor to chemically stabilize the perovskite crystal structure against thermal stress.
📋 **Clip Abstract** This clip explores how tailoring hybrid organic-inorganic perovskite chemistry to a wider bandgap matches the emission spectrum of indoor light sources for optimal efficiency. It also explains how the absence of indoor UV light simplifies device stabilization, shifting the engineering focus toward humidity encapsulation and crystal-lattice optimization.
#IndoorPhotovoltaics, #BandgapEngineering, #GoldschmidtToleranceFactor, #PerovskiteSolarCells, #EnergyHarvesting, #FlexibleElectronics
00:11:53 - 00:13:00
Why Does Carbon Ink Underperform as an ITO Replacement in Printed Perovskite Photovoltaics?
Why Does Carbon Ink Underperform as an ITO Replacement in Printed Perovskite Photovoltaics?
While carbon inks are widely explored as low-cost, highly conductive alternatives for printable solar cells, simply reducing sheet resistance does not guarantee superior PV performance. Substituting screen-printed indium tin oxide (ITO) with carbon often leads to a drop in overall power generation. This degradation stems from complex interfacial physics, where band alignment and work-function mismatch between carbon and the adjacent transport layers hurt charge extraction efficiency.
Currently, SOLRA-PV's screen-printed ITO inks undergo conventional thermal sintering at 590°C to achieve a sheet resistance of 200 ohms per square. However, this high thermal budget limits the choice of flexible substrates and increases manufacturing cycle times.
To bypass these thermal limits, the team is evaluating photonic flash sintering using specialized intense pulsed light tools. This approach successfully drops the sheet resistance of the printed ITO down to 10 ohms per square in milliseconds, paving the way for ultra-low resistance transparent electrodes on heat-sensitive materials.
In this short video, you can learn:
* Why carbon ink fails as a direct drop-in replacement for ITO despite its excellent sheet resistance.
* The current thermal sintering parameters required to process screen-printed ITO electrodes.
* How photonic flash sintering lowers ITO sheet resistance to 10 ohms per square without degrading substrates.
📋 **Clip Abstract** In this Q&A segment, the speaker addresses the thermal and electrical performance characteristics of screen-printed ITO. He explains why carbon replacements degrade efficiency and how flash sintering can bypass high-temperature processing limits.
#PhotonicSintering, #PerovskitePhotovoltaics, #TransparentElectrodes, #CarbonInks, #PrintedElectronics, #FlexibleElectronics