Gordon Elger | Technische Hochschule Ingolstadt: You've achieved near-bulk conductivity with your printed copper ink, but is it useless within days?
00:15:42 - 00:16:54
Other snippets from this talk
Summary of the clip:
You've achieved near-bulk conductivity with your printed copper ink, but is it useless within days?
The primary goal of developing a conductive ink is achieving high electrical performance, and this particle-free copper system successfully delivers on that front. Through careful optimization of the ink formulation and the sintering process, it is possible to produce printed traces with an electrical conductivity as high as 50% that of bulk copper. This represents an excellent result for a low-temperature, additively manufactured conductor, making it attractive for many applications.
However, this high performance is coupled with a critical reliability flaw: poor environmental stability. The resulting film is pure, slightly porous copper with a high surface area, making it extremely susceptible to oxidation. When exposed to ambient air, the trace's resistivity begins to increase, and this degradation is dramatically accelerated under standard 85°C / 85% relative humidity testing conditions, where the conductivity quickly plummets.
The root cause of this failure is the very purity of the copper film. Unlike many particle-based inks that leave behind a residual organic binder that can offer some protection, this process yields unprotected metal. Therefore, a secondary encapsulation step is not an optional improvement but an absolute necessity for any practical application. This can be achieved by applying a traditional solder resist or by developing advanced inks that incorporate polymers for in-situ encapsulation during the curing process.
In this short video, you can learn:
* How to achieve high electrical conductivity (50% of bulk copper) with particle-free inks.
* The critical reliability issue: rapid oxidation and conductivity loss in ambient and humid environments.
* Why encapsulation is a mandatory step for creating environmentally stable printed copper traces.
📋 **Clip Abstract** This clip highlights the double-edged sword of using particle-free inks to create pure copper traces. While they can achieve excellent initial electrical conductivity, they are highly susceptible to oxidation, leading to rapid performance degradation unless properly encapsulated.
🔗 Link in comments 👇
#ParticleFreeCopperInk, #PrintedConductors, #OxidationStability, #EncapsulationTechnology, #PrintedElectronics, #AdditiveElectronics
This is a highlight of the presentation:
More Highlights from the same talk.
05:34 - 07:03
How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers?
How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers?
The ink is salt-based: copper formate is mixed with a complexing agent, then combined with a high-viscosity medium that allows application by dispensing or inkjetting. Copper loading caps at 20% in the salt-based formulation. Diluting further lowers the copper content, an advantage where thinner deposits are wanted, but the wrong route for applications requiring thicker layers. Formulation therefore sets the deposition window.
In current trials the salt-based copper ink is mostly dispensed, but an ink printer is also on hand and the material is being inkjet-printed too. Across both routes the decisive variable is simply copper percentage: it fixes how much copper the deposit carries and therefore which applications the ink can serve.
Two plant-derived biopolymers are under evaluation: PHB and nylon P4. Their thermal stabilities differ markedly and that sets the process ceiling. P4 is the more robust, with superior stability in the 200 to 240 degree range. PHB tops out at about 170 degrees, which is the maximum temperature it can be processed at when paired with the copper ink.
In this short video, you can learn:
* The salt-based copper formate ink reaches a maximum of 20% copper, so further dilution trades copper content for thinner deposits.
* Current trials rely mainly on dispensing, with inkjetting demonstrated on an ink printer.
* P4 biopolymer tolerates 200 to 240 degrees while PHB is limited to about 170 degrees.
📋 **Clip Abstract** A salt-based copper formate ink, mixed with a complexing agent and a high-viscosity medium, is dispensed or inkjet-printed onto plant-derived PHB and nylon P4 biopolymers at a maximum 20% copper loading. Because PHB processes only to about 170 degrees while P4 withstands 200 to 240 degrees, the polymer choice sets the thermal ceiling for the additive metallization.
About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#CopperFormateInk, #SaltBasedInk, #PHBvsP4, #DispenseAndInkjet, #AdditiveElectronics, #CircularElectronics
12:05 - 13:47
What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling?
What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling?
PHB sets the thermal ceiling: sintering runs at 140 °C for 30 minutes because the polymer must stay below 170 °C. PA4 allows 200 °C. The expected copper-sintering trend appears—higher temperature improves conductivity—but the 140 °C result is still characterised as “not bad” at 50, 10 minus six microohm centimetre, roughly 40 times bulk copper.
Recycling starts with manufacturing waste. The board waste is placed into the carrier solution, which dissolves the polymer. Copper separates and falls down, leaving polymer and copper as distinct fractions. The copper can then be removed from the polymer, enabling full recycling. The carrier-solution route is intended to recreate films, returning to the same material that was drop-cast or sprayed.
The stated vision is materials that can be fully recycled after additive board manufacturing. Polymer is dissolved in carrier solution, copper falls out and is separated, and films are recreated from the solution. The endpoint is the same material originally drop-cast or sprayed, now with copper extracted. That closes the described loop from manufacturing waste back to reusable polymer solution and recovered copper.
In this short video, you can learn:
* PHB is sintered at 140 °C for 30 minutes to remain below its 170 °C limit, while PA4 permits 200 °C.
* At 140 °C the copper ink reaches 50, 10 minus six microohm centimetre, about 40 times bulk copper.
* Manufacturing waste is dissolved in carrier solution so copper separates from polymer and films can be recreated.
📋 **Clip Abstract** Copper ink is sintered on PHB at 140 °C for 30 minutes, staying below 170 °C, and on PA4 at 200 °C; higher temperature improves conductivity. The 140 °C board reaches 50, 10 minus six microohm centimetre, roughly 40 times bulk copper, while carrier-solution recycling separates copper from dissolved polymer and recreates the original film material.
About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#CopperSintering, #PHBSubstrate, #CarrierSolutionRecycling, #PolymerCopperSeparation, #SustainableElectronics, #AdditiveElectronics
08:31 - 10:20
At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit?
At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit?
Copper formate salt is complexed with an agent such as H2P. Decomposition of the complexed metal salt occurs around 140°C, even below, and is Arrhenius driven: at 130°C the reaction is possible but needs more time. As temperature drives decomposition, copper nanoparticles build up and grow, the complex agent evaporates, and pure copper remains.
The foil is made from a liquid solution using a dispenser. The blue copper-formate ink is printed, then heated so copper forms. This additive route links the salt-based ink chemistry directly to foil formation. The clip frames the process as printing the ink and thermally converting it into copper.
PHB sets the thermal window. The DTCA and TGA curves show PHB gets liquid at 170°C and degrades at 290°C, so processing must stay below 170°C, or at 150°C to 140°C. That constraint makes the ~140°C copper-formate decomposition relevant: low enough for PHB, but time-dependent at 130°C.
In this short video, you can learn:
* Complexed copper formate decomposes at about 140°C, even below, and at 130°C requires longer time because the process is Arrhenius driven.
* Copper nanoparticles build up and grow during decomposition, the complex agent evaporates, and pure copper remains.
* PHB liquefies at 170°C and degrades at 290°C, so the process window is below 170°C, down to 150–140°C.
📋 **Clip Abstract** The clip explains how a copper-formate salt complexed with an agent such as H2P decomposes around 140°C, or at 130°C with longer time, yielding copper nanoparticles and then pure copper as the complex agent evaporates. It then ties that chemistry to dispenser-printed foil formation on PHB, whose DTCA/TGA curves show liquefaction at 170°C and degradation at 290°C, forcing processing below 170°C and preferably at 150–140°C.
About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin
Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped
#CopperFormateComplex, #ArrheniusDecomposition, #PHBThermalWindow, #DispenserPrintedFoil, #AdditiveElectronics, #SustainableElectronics
Other talks by Gordon Elger
- Additive manufacturing of Circular Flexible Electronics: Cu Particle-free Inks on Recyclable Biopolymers · Sustainable Electronics RESHAPED 2026 Berlin
- Particle Free Copper Inks · The Future of Electronics RESHAPED 2024 Berlin
More highlights from Gordon Elger
- ▶ How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ Why does low-temperature sintered copper oxidise more than bulk copper, and how must printed traces be protected? · Sustainable Electronics RESHAPED 2026 | Berlin
- ▶ How do you sinter metal from a salt-based ink without ending up with useless, oversized particles? · The Future of Electronics RESHAPED 2024
- ▶ Your copper formate ink isn't just decomposing, it's evaporating. Are you losing your precursor before it can form a conductive trace? · The Future of Electronics RESHAPED 2024


