top of page

Gordon Elger

Technische Hochschule Ingolstadt

* All members of the platform can watch the entire presentation.

 

Please register to become a member.

Gordon Elger | Technische Hochschule Ingolstadt: Your copper formate ink isn't just decomposing, it's evaporating. Are you losing your precursor before it can form a conductive trace?

00:08:29 - 00:10:19

Other snippets from this talk

Summary of the clip:

Your copper formate ink isn't just decomposing, it's evaporating. Are you losing your precursor before it can form a conductive trace?

A deep dive into the thermal behavior of copper formate, a common precursor for particle-free inks, reveals complex and challenging chemistry. Thermogravimetric analysis (TGA) shows that while copper formate can form on copper oxide surfaces around 150°C, its primary decomposition into metallic copper doesn't occur until approximately 200°C. This defines a critical temperature window for processing.

A significant and often overlooked issue is that copper formate can sublimate, or evaporate, at the same temperature it decomposes. This creates a competing reaction pathway where the precursor material can be lost to the gas phase instead of converting into the desired metallic copper film. If the heating rate and temperature are not precisely controlled, this evaporation can lead to a significant reduction in the final copper yield and result in thin, non-conductive traces.

Furthermore, the decomposition reaction itself releases a large volume of gaseous byproducts, including carbon dioxide (CO2) and hydrogen (H2). This massive outgassing event must be managed very carefully through slow, controlled heating profiles. If the process is too rapid, the escaping gas will create a highly porous, uneven, and structurally unsound layer, completely compromising the electrical performance of the printed feature.

In this short video, you can learn:
* The specific temperature window for copper formate decomposition (~200°C).
* The competing processes of decomposition and evaporation that can lead to material loss.
* The significant outgassing of CO2 and H2, which poses a major process control challenge.

📋 **Clip Abstract** This segment provides a deep dive into the complex chemistry of copper formate, the precursor for many particle-free copper inks. It reveals the critical processing challenge of managing its simultaneous decomposition and evaporation, along with the significant outgassing that must be controlled for successful sintering.
🔗 Link in comments 👇

#CopperFormateInk, #ThermalDecomposition, #PrecursorSublimation, #OutgassingManagement, #PrintedElectronics, #AdditiveElectronics

This is a highlight of the presentation:

​

The Future of Electronics RESHAPED 2024

​

23-24 OCT 2024

Estrel Congress Centre, Berlin, Germany

Organised By:

TechBlick

​

More Highlights from the same talk.

05:34 - 07:03

How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers?

How does copper formate ink formulation compare to traditional inks, and what are the thermal limits of PHB versus PA4 biopolymers?

The ink is salt-based: copper formate is mixed with a complexing agent, then combined with a high-viscosity medium that allows application by dispensing or inkjetting. Copper loading caps at 20% in the salt-based formulation. Diluting further lowers the copper content, an advantage where thinner deposits are wanted, but the wrong route for applications requiring thicker layers. Formulation therefore sets the deposition window.

In current trials the salt-based copper ink is mostly dispensed, but an ink printer is also on hand and the material is being inkjet-printed too. Across both routes the decisive variable is simply copper percentage: it fixes how much copper the deposit carries and therefore which applications the ink can serve.

Two plant-derived biopolymers are under evaluation: PHB and nylon P4. Their thermal stabilities differ markedly and that sets the process ceiling. P4 is the more robust, with superior stability in the 200 to 240 degree range. PHB tops out at about 170 degrees, which is the maximum temperature it can be processed at when paired with the copper ink.

In this short video, you can learn:
* The salt-based copper formate ink reaches a maximum of 20% copper, so further dilution trades copper content for thinner deposits.
* Current trials rely mainly on dispensing, with inkjetting demonstrated on an ink printer.
* P4 biopolymer tolerates 200 to 240 degrees while PHB is limited to about 170 degrees.

📋 **Clip Abstract** A salt-based copper formate ink, mixed with a complexing agent and a high-viscosity medium, is dispensed or inkjet-printed onto plant-derived PHB and nylon P4 biopolymers at a maximum 20% copper loading. Because PHB processes only to about 170 degrees while P4 withstands 200 to 240 degrees, the polymer choice sets the thermal ceiling for the additive metallization.

About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#CopperFormateInk, #SaltBasedInk, #PHBvsP4, #DispenseAndInkjet, #AdditiveElectronics, #CircularElectronics

12:05 - 13:47

What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling?

What resistivity does copper ink reach on PHB after 140 °C sintering, and how is the polymer separated for recycling?

PHB sets the thermal ceiling: sintering runs at 140 °C for 30 minutes because the polymer must stay below 170 °C. PA4 allows 200 °C. The expected copper-sintering trend appears—higher temperature improves conductivity—but the 140 °C result is still characterised as “not bad” at 50, 10 minus six microohm centimetre, roughly 40 times bulk copper.

Recycling starts with manufacturing waste. The board waste is placed into the carrier solution, which dissolves the polymer. Copper separates and falls down, leaving polymer and copper as distinct fractions. The copper can then be removed from the polymer, enabling full recycling. The carrier-solution route is intended to recreate films, returning to the same material that was drop-cast or sprayed.

The stated vision is materials that can be fully recycled after additive board manufacturing. Polymer is dissolved in carrier solution, copper falls out and is separated, and films are recreated from the solution. The endpoint is the same material originally drop-cast or sprayed, now with copper extracted. That closes the described loop from manufacturing waste back to reusable polymer solution and recovered copper.

In this short video, you can learn:
* PHB is sintered at 140 °C for 30 minutes to remain below its 170 °C limit, while PA4 permits 200 °C.
* At 140 °C the copper ink reaches 50, 10 minus six microohm centimetre, about 40 times bulk copper.
* Manufacturing waste is dissolved in carrier solution so copper separates from polymer and films can be recreated.

📋 **Clip Abstract** Copper ink is sintered on PHB at 140 °C for 30 minutes, staying below 170 °C, and on PA4 at 200 °C; higher temperature improves conductivity. The 140 °C board reaches 50, 10 minus six microohm centimetre, roughly 40 times bulk copper, while carrier-solution recycling separates copper from dissolved polymer and recreates the original film material.

About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#CopperSintering, #PHBSubstrate, #CarrierSolutionRecycling, #PolymerCopperSeparation, #SustainableElectronics, #AdditiveElectronics

08:31 - 10:20

At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit?

At what temperature does complexed copper formate decompose to copper without exceeding PHB's 170°C processing limit?

Copper formate salt is complexed with an agent such as H2P. Decomposition of the complexed metal salt occurs around 140°C, even below, and is Arrhenius driven: at 130°C the reaction is possible but needs more time. As temperature drives decomposition, copper nanoparticles build up and grow, the complex agent evaporates, and pure copper remains.

The foil is made from a liquid solution using a dispenser. The blue copper-formate ink is printed, then heated so copper forms. This additive route links the salt-based ink chemistry directly to foil formation. The clip frames the process as printing the ink and thermally converting it into copper.

PHB sets the thermal window. The DTCA and TGA curves show PHB gets liquid at 170°C and degrades at 290°C, so processing must stay below 170°C, or at 150°C to 140°C. That constraint makes the ~140°C copper-formate decomposition relevant: low enough for PHB, but time-dependent at 130°C.

In this short video, you can learn:
* Complexed copper formate decomposes at about 140°C, even below, and at 130°C requires longer time because the process is Arrhenius driven.
* Copper nanoparticles build up and grow during decomposition, the complex agent evaporates, and pure copper remains.
* PHB liquefies at 170°C and degrades at 290°C, so the process window is below 170°C, down to 150–140°C.

📋 **Clip Abstract** The clip explains how a copper-formate salt complexed with an agent such as H2P decomposes around 140°C, or at 130°C with longer time, yielding copper nanoparticles and then pure copper as the complex agent evaporates. It then ties that chemistry to dispenser-printed foil formation on PHB, whose DTCA/TGA curves show liquefaction at 170°C and degradation at 290°C, forcing processing below 170°C and preferably at 150–140°C.

About the speaker:
* Speaker: Gordon Elger
* Company: Technische Hochschule Ingolstadt
* Event: Sustainable Electronics RESHAPED 2026 | Berlin
* Location: Estrel, Berlin

Sustainable Electronics RESHAPED | Berlin
📅 Save the date: 20 and 21 October 2027
📍 Berlin, Germany
📋 Info: https://www.techblick.com/sustainableelectronicsreshaped

#CopperFormateComplex, #ArrheniusDecomposition, #PHBThermalWindow, #DispenserPrintedFoil, #AdditiveElectronics, #SustainableElectronics

More Snippets
CONTACT US

KGH Concepts GmbH

Mergenthalerallee 73-75, 65760, Eschborn

+49 17661704139

admin@techblick.com

TechBlick is owned and operated by KGH Concepts GmbH

Registration number HRB 121362

VAT number: DE 337022439

  • LinkedIn
  • YouTube

Sign up for our newsletter to receive updates on our latest speakers and events AND to receive analyst-written summaries of the key talks and happenings in our events.

Thanks for submitting!

© 2026 by KGH Concepts GmbH

bottom of page